| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Wed, 22 Jul 2009 13:47:56 -0400
From: "John W. Linville" <linville@...driver.com>
To: davem@...emloft.net
Cc: linux-wireless@...r.kernel.org, netdev@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: pull request: wireless-2.6 2009-07-22
Dave,
Here is a collection of fixes intended for 2.6.31. I think they mostly
speak for themselves and are uncontroversial.
Please let me know if there are problems!
Thanks,
John
---
Individual patches are available here:
http://www.kernel.org/pub/linux/kernel/people/linville/wireless-2.6/
---
The following changes since commit 1b0d92244ff2434a98272f6d2525da32fc230f19:
Wolfgang Grandegger (1):
can: switch carrier on if device was stopped while in bus-off state
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git master
Alan Jenkins (3):
rfkill: fix rfkill_set_states() to set the hw state
rfkill: remove too-strict __must_check
acer-wmi: fix rfkill conversion
Andy Whitcroft (1):
rt2x00: Fix chipset detection for rt2500usb
Bob Copeland (1):
ath5k: temporarily disable crypto for AP mode
Christian Lamparter (1):
cfg80211: double free in __cfg80211_scan_done
Dan Carpenter (1):
p54spi: fix potential null deref in p54spi.c
Javier Cardona (1):
mac80211: use correct address for mesh Path Error
Johannes Berg (4):
mac80211: disable mesh
rfkill: allow toggling soft state in sysfs again
mac80211_hwsim: fix unregistration
mac80211_hwsim: fix use after free
Larry Finger (1):
rtl8187: Fix for kernel oops when unloading with LEDs enabled
Luis R. Rodriguez (2):
ath9k: Tune ANI function processing on AP mode during ANI reset
ath: add support for special 0x8000 regulatory domain
Marek Vasut (1):
libertas: Fix problem with broken V4 firmware on CF8381
Niko Jokinen (1):
nl80211: Memory leak fixed
Pavel Roskin (1):
mac80211: fix injection in monitor mode
Reinette Chatre (2):
iwlwifi: only show active power level via sysfs
iwlwifi: only update byte count table during aggregation
Zhu Yi (1):
iwmc3200wifi: fix NULL pointer dereference in iwm_if_free
drivers/net/wireless/ath/ath5k/base.c | 3 ++
drivers/net/wireless/ath/ath9k/ani.c | 12 ++++++++++
drivers/net/wireless/ath/regd.c | 17 ++++++++++++++
drivers/net/wireless/iwlwifi/iwl-agn.c | 4 +--
drivers/net/wireless/iwlwifi/iwl-tx.c | 3 +-
drivers/net/wireless/iwlwifi/iwl3945-base.c | 4 +--
drivers/net/wireless/iwmc3200wifi/netdev.c | 2 +-
drivers/net/wireless/libertas/cmd.c | 8 ++++++-
drivers/net/wireless/libertas/defs.h | 2 +
drivers/net/wireless/mac80211_hwsim.c | 6 ++--
drivers/net/wireless/p54/p54spi.c | 2 +-
drivers/net/wireless/rt2x00/rt2500usb.c | 4 ++-
drivers/net/wireless/rtl818x/rtl8187_leds.c | 3 +-
drivers/platform/x86/acer-wmi.c | 2 +-
include/linux/rfkill.h | 2 +-
net/mac80211/Kconfig | 1 +
net/mac80211/mesh_pathtbl.c | 11 +++++++--
net/mac80211/tx.c | 2 +-
net/rfkill/core.c | 31 ++++++++++++++++++++-------
net/wireless/nl80211.c | 5 ++-
net/wireless/scan.c | 3 +-
21 files changed, 94 insertions(+), 33 deletions(-)
diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c
index ea04515..029c1bc 100644
--- a/drivers/net/wireless/ath/ath5k/base.c
+++ b/drivers/net/wireless/ath/ath5k/base.c
@@ -2970,6 +2970,9 @@ ath5k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
if (modparam_nohwcrypt)
return -EOPNOTSUPP;
+ if (sc->opmode == NL80211_IFTYPE_AP)
+ return -EOPNOTSUPP;
+
switch (key->alg) {
case ALG_WEP:
case ALG_TKIP:
diff --git a/drivers/net/wireless/ath/ath9k/ani.c b/drivers/net/wireless/ath/ath9k/ani.c
index 1aeafb5..aad259b 100644
--- a/drivers/net/wireless/ath/ath9k/ani.c
+++ b/drivers/net/wireless/ath/ath9k/ani.c
@@ -478,6 +478,18 @@ void ath9k_ani_reset(struct ath_hw *ah)
"Reset ANI state opmode %u\n", ah->opmode);
ah->stats.ast_ani_reset++;
+ if (ah->opmode == NL80211_IFTYPE_AP) {
+ /*
+ * ath9k_hw_ani_control() will only process items set on
+ * ah->ani_function
+ */
+ if (IS_CHAN_2GHZ(chan))
+ ah->ani_function = (ATH9K_ANI_SPUR_IMMUNITY_LEVEL |
+ ATH9K_ANI_FIRSTEP_LEVEL);
+ else
+ ah->ani_function = 0;
+ }
+
ath9k_hw_ani_control(ah, ATH9K_ANI_NOISE_IMMUNITY_LEVEL, 0);
ath9k_hw_ani_control(ah, ATH9K_ANI_SPUR_IMMUNITY_LEVEL, 0);
ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL, 0);
diff --git a/drivers/net/wireless/ath/regd.c b/drivers/net/wireless/ath/regd.c
index eef370b..bf3d25b 100644
--- a/drivers/net/wireless/ath/regd.c
+++ b/drivers/net/wireless/ath/regd.c
@@ -474,6 +474,21 @@ ath_regd_init_wiphy(struct ath_regulatory *reg,
return 0;
}
+/*
+ * Some users have reported their EEPROM programmed with
+ * 0x8000 set, this is not a supported regulatory domain
+ * but since we have more than one user with it we need
+ * a solution for them. We default to 0x64, which is the
+ * default Atheros world regulatory domain.
+ */
+static void ath_regd_sanitize(struct ath_regulatory *reg)
+{
+ if (reg->current_rd != COUNTRY_ERD_FLAG)
+ return;
+ printk(KERN_DEBUG "ath: EEPROM regdomain sanitized\n");
+ reg->current_rd = 0x64;
+}
+
int
ath_regd_init(struct ath_regulatory *reg,
struct wiphy *wiphy,
@@ -486,6 +501,8 @@ ath_regd_init(struct ath_regulatory *reg,
if (!reg)
return -EINVAL;
+ ath_regd_sanitize(reg);
+
printk(KERN_DEBUG "ath: EEPROM regdomain: 0x%0x\n", reg->current_rd);
if (!ath_regd_is_eeprom_valid(reg)) {
diff --git a/drivers/net/wireless/iwlwifi/iwl-agn.c b/drivers/net/wireless/iwlwifi/iwl-agn.c
index 6d1519e..355f50e 100644
--- a/drivers/net/wireless/iwlwifi/iwl-agn.c
+++ b/drivers/net/wireless/iwlwifi/iwl-agn.c
@@ -2675,12 +2675,10 @@ static ssize_t show_power_level(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = dev_get_drvdata(d);
- int mode = priv->power_data.user_power_setting;
int level = priv->power_data.power_mode;
char *p = buf;
- p += sprintf(p, "INDEX:%d\t", level);
- p += sprintf(p, "USER:%d\n", mode);
+ p += sprintf(p, "%d\n", level);
return p - buf + 1;
}
diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c
index 85ae7a6..9bbeec9 100644
--- a/drivers/net/wireless/iwlwifi/iwl-tx.c
+++ b/drivers/net/wireless/iwlwifi/iwl-tx.c
@@ -872,7 +872,8 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb)
iwl_print_hex_dump(priv, IWL_DL_TX, (u8 *)tx_cmd->hdr, hdr_len);
/* Set up entry for this TFD in Tx byte-count array */
- priv->cfg->ops->lib->txq_update_byte_cnt_tbl(priv, txq,
+ if (info->flags & IEEE80211_TX_CTL_AMPDU)
+ priv->cfg->ops->lib->txq_update_byte_cnt_tbl(priv, txq,
le16_to_cpu(tx_cmd->len));
pci_dma_sync_single_for_device(priv->pci_dev, txcmd_phys,
diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c
index cb9bd4c..956798f 100644
--- a/drivers/net/wireless/iwlwifi/iwl3945-base.c
+++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c
@@ -3643,12 +3643,10 @@ static ssize_t show_power_level(struct device *d,
struct device_attribute *attr, char *buf)
{
struct iwl_priv *priv = dev_get_drvdata(d);
- int mode = priv->power_data.user_power_setting;
int level = priv->power_data.power_mode;
char *p = buf;
- p += sprintf(p, "INDEX:%d\t", level);
- p += sprintf(p, "USER:%d\n", mode);
+ p += sprintf(p, "%d\n", level);
return p - buf + 1;
}
diff --git a/drivers/net/wireless/iwmc3200wifi/netdev.c b/drivers/net/wireless/iwmc3200wifi/netdev.c
index aaa20c6..aea5ccf 100644
--- a/drivers/net/wireless/iwmc3200wifi/netdev.c
+++ b/drivers/net/wireless/iwmc3200wifi/netdev.c
@@ -151,8 +151,8 @@ void iwm_if_free(struct iwm_priv *iwm)
return;
free_netdev(iwm_to_ndev(iwm));
- iwm_wdev_free(iwm);
iwm_priv_deinit(iwm);
+ iwm_wdev_free(iwm);
}
int iwm_if_add(struct iwm_priv *iwm)
diff --git a/drivers/net/wireless/libertas/cmd.c b/drivers/net/wireless/libertas/cmd.c
index 01db705..6850981 100644
--- a/drivers/net/wireless/libertas/cmd.c
+++ b/drivers/net/wireless/libertas/cmd.c
@@ -135,8 +135,14 @@ int lbs_update_hw_spec(struct lbs_private *priv)
/* Clamp region code to 8-bit since FW spec indicates that it should
* only ever be 8-bit, even though the field size is 16-bit. Some firmware
* returns non-zero high 8 bits here.
+ *
+ * Firmware version 4.0.102 used in CF8381 has region code shifted. We
+ * need to check for this problem and handle it properly.
*/
- priv->regioncode = le16_to_cpu(cmd.regioncode) & 0xFF;
+ if (MRVL_FW_MAJOR_REV(priv->fwrelease) == MRVL_FW_V4)
+ priv->regioncode = (le16_to_cpu(cmd.regioncode) >> 8) & 0xFF;
+ else
+ priv->regioncode = le16_to_cpu(cmd.regioncode) & 0xFF;
for (i = 0; i < MRVDRV_MAX_REGION_CODE; i++) {
/* use the region code to search for the index */
diff --git a/drivers/net/wireless/libertas/defs.h b/drivers/net/wireless/libertas/defs.h
index 48da157..72f3479 100644
--- a/drivers/net/wireless/libertas/defs.h
+++ b/drivers/net/wireless/libertas/defs.h
@@ -234,6 +234,8 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in
/** Mesh enable bit in FW capability */
#define MESH_CAPINFO_ENABLE_MASK (1<<16)
+/** FW definition from Marvell v4 */
+#define MRVL_FW_V4 (0x04)
/** FW definition from Marvell v5 */
#define MRVL_FW_V5 (0x05)
/** FW definition from Marvell v10 */
diff --git a/drivers/net/wireless/mac80211_hwsim.c b/drivers/net/wireless/mac80211_hwsim.c
index a111bda..7916ca3 100644
--- a/drivers/net/wireless/mac80211_hwsim.c
+++ b/drivers/net/wireless/mac80211_hwsim.c
@@ -709,7 +709,7 @@ static const struct ieee80211_ops mac80211_hwsim_ops =
static void mac80211_hwsim_free(void)
{
struct list_head tmplist, *i, *tmp;
- struct mac80211_hwsim_data *data;
+ struct mac80211_hwsim_data *data, *tmpdata;
INIT_LIST_HEAD(&tmplist);
@@ -718,7 +718,7 @@ static void mac80211_hwsim_free(void)
list_move(i, &tmplist);
spin_unlock_bh(&hwsim_radio_lock);
- list_for_each_entry(data, &tmplist, list) {
+ list_for_each_entry_safe(data, tmpdata, &tmplist, list) {
debugfs_remove(data->debugfs_group);
debugfs_remove(data->debugfs_ps);
debugfs_remove(data->debugfs);
@@ -1167,8 +1167,8 @@ static void __exit exit_mac80211_hwsim(void)
{
printk(KERN_DEBUG "mac80211_hwsim: unregister radios\n");
- unregister_netdev(hwsim_mon);
mac80211_hwsim_free();
+ unregister_netdev(hwsim_mon);
}
diff --git a/drivers/net/wireless/p54/p54spi.c b/drivers/net/wireless/p54/p54spi.c
index 83116ba..72c7dbd 100644
--- a/drivers/net/wireless/p54/p54spi.c
+++ b/drivers/net/wireless/p54/p54spi.c
@@ -635,7 +635,7 @@ static int __devinit p54spi_probe(struct spi_device *spi)
hw = p54_init_common(sizeof(*priv));
if (!hw) {
- dev_err(&priv->spi->dev, "could not alloc ieee80211_hw");
+ dev_err(&spi->dev, "could not alloc ieee80211_hw");
return -ENOMEM;
}
diff --git a/drivers/net/wireless/rt2x00/rt2500usb.c b/drivers/net/wireless/rt2x00/rt2500usb.c
index 66daf68..ce75426 100644
--- a/drivers/net/wireless/rt2x00/rt2500usb.c
+++ b/drivers/net/wireless/rt2x00/rt2500usb.c
@@ -1550,7 +1550,9 @@ static int rt2500usb_init_eeprom(struct rt2x00_dev *rt2x00dev)
rt2500usb_register_read(rt2x00dev, MAC_CSR0, ®);
rt2x00_set_chip(rt2x00dev, RT2570, value, reg);
- if (!rt2x00_check_rev(&rt2x00dev->chip, 0x000ffff0, 0)) {
+ if (!rt2x00_check_rev(&rt2x00dev->chip, 0x000ffff0, 0) ||
+ rt2x00_check_rev(&rt2x00dev->chip, 0x0000000f, 0)) {
+
ERROR(rt2x00dev, "Invalid RT chipset detected.\n");
return -ENODEV;
}
diff --git a/drivers/net/wireless/rtl818x/rtl8187_leds.c b/drivers/net/wireless/rtl818x/rtl8187_leds.c
index b442535..cf9f899 100644
--- a/drivers/net/wireless/rtl818x/rtl8187_leds.c
+++ b/drivers/net/wireless/rtl818x/rtl8187_leds.c
@@ -208,11 +208,12 @@ void rtl8187_leds_exit(struct ieee80211_hw *dev)
{
struct rtl8187_priv *priv = dev->priv;
- rtl8187_unregister_led(&priv->led_tx);
/* turn the LED off before exiting */
queue_delayed_work(dev->workqueue, &priv->led_off, 0);
cancel_delayed_work_sync(&priv->led_off);
+ cancel_delayed_work_sync(&priv->led_on);
rtl8187_unregister_led(&priv->led_rx);
+ rtl8187_unregister_led(&priv->led_tx);
}
#endif /* def CONFIG_RTL8187_LED */
diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c
index be2fd6f..fb45f5e 100644
--- a/drivers/platform/x86/acer-wmi.c
+++ b/drivers/platform/x86/acer-wmi.c
@@ -973,7 +973,7 @@ static int acer_rfkill_set(void *data, bool blocked)
{
acpi_status status;
u32 cap = (unsigned long)data;
- status = set_u32(!!blocked, cap);
+ status = set_u32(!blocked, cap);
if (ACPI_FAILURE(status))
return -ENODEV;
return 0;
diff --git a/include/linux/rfkill.h b/include/linux/rfkill.h
index 2ce2983..278777f 100644
--- a/include/linux/rfkill.h
+++ b/include/linux/rfkill.h
@@ -224,7 +224,7 @@ void rfkill_destroy(struct rfkill *rfkill);
* should be blocked) so that drivers need not keep track of the soft
* block state -- which they might not be able to.
*/
-bool __must_check rfkill_set_hw_state(struct rfkill *rfkill, bool blocked);
+bool rfkill_set_hw_state(struct rfkill *rfkill, bool blocked);
/**
* rfkill_set_sw_state - Set the internal rfkill software block state
diff --git a/net/mac80211/Kconfig b/net/mac80211/Kconfig
index ba2643a..7836ee9 100644
--- a/net/mac80211/Kconfig
+++ b/net/mac80211/Kconfig
@@ -83,6 +83,7 @@ endmenu
config MAC80211_MESH
bool "Enable mac80211 mesh networking (pre-802.11s) support"
depends on MAC80211 && EXPERIMENTAL
+ depends on BROKEN
---help---
This options enables support of Draft 802.11s mesh networking.
The implementation is based on Draft 1.08 of the Mesh Networking
diff --git a/net/mac80211/mesh_pathtbl.c b/net/mac80211/mesh_pathtbl.c
index 3c72557..479597e 100644
--- a/net/mac80211/mesh_pathtbl.c
+++ b/net/mac80211/mesh_pathtbl.c
@@ -175,6 +175,8 @@ int mesh_path_add(u8 *dst, struct ieee80211_sub_if_data *sdata)
int err = 0;
u32 hash_idx;
+ might_sleep();
+
if (memcmp(dst, sdata->dev->dev_addr, ETH_ALEN) == 0)
/* never add ourselves as neighbours */
return -ENOTSUPP;
@@ -265,6 +267,7 @@ int mpp_path_add(u8 *dst, u8 *mpp, struct ieee80211_sub_if_data *sdata)
int err = 0;
u32 hash_idx;
+ might_sleep();
if (memcmp(dst, sdata->dev->dev_addr, ETH_ALEN) == 0)
/* never add ourselves as neighbours */
@@ -491,8 +494,10 @@ void mesh_path_tx_pending(struct mesh_path *mpath)
* @skb: frame to discard
* @sdata: network subif the frame was to be sent through
*
- * If the frame was beign forwarded from another MP, a PERR frame will be sent
- * to the precursor.
+ * If the frame was being forwarded from another MP, a PERR frame will be sent
+ * to the precursor. The precursor's address (i.e. the previous hop) was saved
+ * in addr1 of the frame-to-be-forwarded, and would only be overwritten once
+ * the destination is successfully resolved.
*
* Locking: the function must me called within a rcu_read_lock region
*/
@@ -507,7 +512,7 @@ void mesh_path_discard_frame(struct sk_buff *skb,
u8 *ra, *da;
da = hdr->addr3;
- ra = hdr->addr2;
+ ra = hdr->addr1;
mpath = mesh_path_lookup(da, sdata);
if (mpath)
dsn = ++mpath->dsn;
diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c
index d238a89..3a8922c 100644
--- a/net/mac80211/tx.c
+++ b/net/mac80211/tx.c
@@ -1455,7 +1455,7 @@ int ieee80211_master_start_xmit(struct sk_buff *skb, struct net_device *dev)
monitor_iface = UNKNOWN_ADDRESS;
len_rthdr = ieee80211_get_radiotap_len(skb->data);
- hdr = (struct ieee80211_hdr *)skb->data + len_rthdr;
+ hdr = (struct ieee80211_hdr *)(skb->data + len_rthdr);
hdrlen = ieee80211_hdrlen(hdr->frame_control);
/* check the header is complete in the frame */
diff --git a/net/rfkill/core.c b/net/rfkill/core.c
index 79693fe..2fc4a17 100644
--- a/net/rfkill/core.c
+++ b/net/rfkill/core.c
@@ -549,6 +549,10 @@ void rfkill_set_states(struct rfkill *rfkill, bool sw, bool hw)
swprev = !!(rfkill->state & RFKILL_BLOCK_SW);
hwprev = !!(rfkill->state & RFKILL_BLOCK_HW);
__rfkill_set_sw_state(rfkill, sw);
+ if (hw)
+ rfkill->state |= RFKILL_BLOCK_HW;
+ else
+ rfkill->state &= ~RFKILL_BLOCK_HW;
spin_unlock_irqrestore(&rfkill->lock, flags);
@@ -648,15 +652,26 @@ static ssize_t rfkill_state_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
- /*
- * The intention was that userspace can only take control over
- * a given device when/if rfkill-input doesn't control it due
- * to user_claim. Since user_claim is currently unsupported,
- * we never support changing the state from userspace -- this
- * can be implemented again later.
- */
+ struct rfkill *rfkill = to_rfkill(dev);
+ unsigned long state;
+ int err;
+
+ if (!capable(CAP_NET_ADMIN))
+ return -EPERM;
+
+ err = strict_strtoul(buf, 0, &state);
+ if (err)
+ return err;
+
+ if (state != RFKILL_USER_STATE_SOFT_BLOCKED &&
+ state != RFKILL_USER_STATE_UNBLOCKED)
+ return -EINVAL;
+
+ mutex_lock(&rfkill_global_mutex);
+ rfkill_set_block(rfkill, state == RFKILL_USER_STATE_SOFT_BLOCKED);
+ mutex_unlock(&rfkill_global_mutex);
- return -EPERM;
+ return err ?: count;
}
static ssize_t rfkill_claim_show(struct device *dev,
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 43bdb13..634496b 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -997,7 +997,7 @@ static int nl80211_get_key(struct sk_buff *skb, struct genl_info *info)
if (IS_ERR(hdr)) {
err = PTR_ERR(hdr);
- goto out;
+ goto free_msg;
}
cookie.msg = msg;
@@ -1011,7 +1011,7 @@ static int nl80211_get_key(struct sk_buff *skb, struct genl_info *info)
&cookie, get_key_callback);
if (err)
- goto out;
+ goto free_msg;
if (cookie.error)
goto nla_put_failure;
@@ -1022,6 +1022,7 @@ static int nl80211_get_key(struct sk_buff *skb, struct genl_info *info)
nla_put_failure:
err = -ENOBUFS;
+ free_msg:
nlmsg_free(msg);
out:
cfg80211_put_dev(drv);
diff --git a/net/wireless/scan.c b/net/wireless/scan.c
index f8e71b3..9271118 100644
--- a/net/wireless/scan.c
+++ b/net/wireless/scan.c
@@ -35,8 +35,6 @@ void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted)
else
nl80211_send_scan_done(wiphy_to_dev(request->wiphy), dev);
- wiphy_to_dev(request->wiphy)->scan_req = NULL;
-
#ifdef CONFIG_WIRELESS_EXT
if (!aborted) {
memset(&wrqu, 0, sizeof(wrqu));
@@ -48,6 +46,7 @@ void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted)
dev_put(dev);
out:
+ wiphy_to_dev(request->wiphy)->scan_req = NULL;
kfree(request);
}
EXPORT_SYMBOL(cfg80211_scan_done);
--
John W. Linville Someday the world will need a hero, and you
linville@...driver.com might be all we have. Be ready.
¡Viva Honduras Libre!
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists