| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <m1tywprvl4.fsf@fess.ebiederm.org> Date: Fri, 20 Nov 2009 08:48:23 -0800 From: ebiederm@...ssion.com (Eric W. Biederman) To: Jens Rosenboom <me@...r.de> Cc: Dhananjay Phadke <dhananjay.phadke@...gic.com>, "netdev\@vger.kernel.org" <netdev@...r.kernel.org>, Amit Salecha <amit.salecha@...gic.com> Subject: Re: [BUG] netxen: Stops working between 2.6.30 and 2.6.31-rc1 Jens Rosenboom <me@...r.de> writes: > On Thu, Nov 19, 2009 at 05:19:05PM -0800, Eric W. Biederman wrote: >> Jens Rosenboom <me@...r.de> writes: >> >> > On Thu, Nov 19, 2009 at 10:07:21AM -0800, Dhananjay Phadke wrote: >> >> > My netxen 10G card stops working somewhere between 2.6.30 and 2.6.31-rc1. >> >> > With the >> >> > newer kernel I can see packets been received on the switch it is >> >> > connected to, but >> >> > the kernel doesn't report any sent packets in the interface counters and >> >> > nothing >> >> > is being received either. >> >> > >> >> > I've tried to bisect this, but only seems the end up with kernels that do >> >> > not boot >> >> > at all because some SCSI stuff goes bad. >> >> >> >> Any particular reason for using -rc1 kernel and not 2.6.31 stable kernel? >> > >> > Sorry, I forgot to mention that all later kernels that I tested >> > including 2.6.31 and the current net-2.6 also fail, so the badness >> > comes in somewhere in between 2.6.30 and 2.6.31-rc1. >> > >> > I also noticed that the newer kernel allocate four interrupts for the >> > card instead of only one, but none of them seem to get triggered, the >> > /proc/interrupts counters all stay at zero. >> >> Hmm. Have you tried disabling msi's? aka putting nomsi on the kernel >> command line. > > I hadn't before but tried it now, but no difference. The kernel still seems to > allocate four interrupts: Weird. MSI's definitely weren't disabled. Looking a little farther at your quoted setup MSI work on your board. This is definitely something specific to the driver. Except for a few initialization races that are an issue for bonding I am running 2.6.31 just fine. > kernel: [ 2.980300] bus: 'pci': add driver netxen_nic > kernel: [ 2.980329] bus: 'pci': driver_probe_device: matched device 0000:22:00.0 with driver netxen_nic > kernel: [ 2.980333] bus: 'pci': really_probe: probing driver netxen_nic with device 0000:22:00.0 > kernel: [ 2.980446] netxen_nic 0000:22:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > kernel: [ 2.980459] netxen_nic 0000:22:00.0: setting latency timer to 64 > kernel: [ 2.981505] netxen_nic 0000:22:00.0: 128MB memory map > kernel: [ 2.981611] netxen_nic 0000:22:00.0: firmware: using built-in firmware nxromimg.bin > kernel: [ 4.144018] netxen_nic 0000:22:00.0: loading firmware from nxromimg.bin > kernel: [ 10.108208] NetXen XGb XFP Board S/N IF72MK0200 Chip rev 0x25 > kernel: [ 10.108211] netxen_nic 0000:22:00.0: firmware version 3.4.336 > kernel: [ 10.108262] alloc irq_desc for 37 on node 0 > kernel: [ 10.108265] alloc kstat_irqs on node 0 > kernel: [ 10.108273] netxen_nic 0000:22:00.0: irq 37 for MSI/MSI-X > kernel: [ 10.108275] alloc irq_desc for 38 on node 0 > kernel: [ 10.108277] alloc kstat_irqs on node 0 > kernel: [ 10.108281] netxen_nic 0000:22:00.0: irq 38 for MSI/MSI-X > kernel: [ 10.108284] alloc irq_desc for 39 on node 0 > kernel: [ 10.108286] alloc kstat_irqs on node 0 > kernel: [ 10.108289] netxen_nic 0000:22:00.0: irq 39 for MSI/MSI-X > kernel: [ 10.108291] alloc irq_desc for 40 on node 0 > kernel: [ 10.108293] alloc kstat_irqs on node 0 > kernel: [ 10.108296] netxen_nic 0000:22:00.0: irq 40 for MSI/MSI-X > kernel: [ 10.108311] netxen_nic 0000:22:00.0: using msi-x interrupts > kernel: [ 10.108371] device: 'eth2': device_add > kernel: [ 10.108442] PM: Adding info for No Bus:eth2 > kernel: [ 10.109197] netxen_nic 0000:22:00.0: eth2: XGbE port initialized > kernel: [ 10.109219] driver: '0000:22:00.0': driver_bound: bound to device 'netxen_nic' > kernel: [ 10.109226] bus: 'pci': really_probe: bound device 0000:22:00.0 to driver netxen_nic > > # grep eth2 /proc/interrupts > 37: 0 0 0 0 PCI-MSI-edge eth2[0] > 38: 0 0 0 0 PCI-MSI-edge eth2[1] > 39: 0 0 0 0 PCI-MSI-edge eth2[2] > 40: 0 0 0 0 PCI-MSI-edge eth2[3] > # ethtool eth2 > Settings for eth2: > Supported ports: [ FIBRE ] > Supported link modes: > Supports auto-negotiation: No > Advertised link modes: 10000baseT/Full > Advertised auto-negotiation: No > Speed: 10000Mb/s > Duplex: Full > Port: FIBRE > PHYAD: 0 > Transceiver: external > Auto-negotiation: off > Supports Wake-on: d > Wake-on: d > Link detected: yes > # ethtool -i eth2 > driver: netxen_nic > version: 4.0.30 > firmware-version: 3.4.336 > bus-info: 0000:22:00.0 > # uname -rvmpi > 2.6.31.6 #5 SMP Wed Nov 18 09:15:48 CET 2009 x86_64 Dual-Core AMD Opteron(tm) Processor 2212 AuthenticAMD GNU/Linux On my working setup I have: driver: netxen_nic version: 4.0.30 firmware-version: 4.0.305 bus-info: 0000:06:00.0 4.0.305 looks like the latest publicly available version on qlogic's website. If that will work on your card I recommend you pull it down and update your firmware. My card is: NetXen Dual XGb SFP+ LP Board S/N SF86BK0008 Chip rev 0x41 Which is a bit different at the physical hardware level. Eric -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists