Message-ID: <14385191E87B904DBD836449AA30269D580A76@MORGANITE.micrel.com>
Date:	Tue, 19 Jan 2010 12:03:20 -0800
From:	"Ha, Tristram" <Tristram.Ha@...rel.Com>
To:	"David Miller" <davem@...emloft.net>
Cc:	<netdev@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
	<shemminger@...tta.com>
Subject: RE: [PATCH 2.6.33 1/3] net: Micrel KSZ8841/2 PCI Ethernet driver

David Miller wrote:
> From: "Ha, Tristram" <Tristram.Ha@...rel.Com>
> Date: Fri, 15 Jan 2010 18:57:59 -0800
> 
>> The KSZ8842 has a switch with lots of hardware configurations.  The =
>> driver uses the proc system to allow users to configure the switch.
>> If = this is not desired the whole thing can be removed by not
calling the =
>> init_proc() function.
> 
> I think there needs to be a serious discussion about how this driver
uses bridge layer internals
> by doing things like: 
> 
> +/* Needed for STP support. */
> +#ifdef CONFIG_KSZ8842_STP
> +#include <../net/bridge/br_private.h>
> +#endif
> 
> and uses procfs to configure the ports.
> 
> Stephen please look this over and make suggestions for better ways to
support and configure
> these kinds of devices. 
> 
> Thanks.

I like to explain a little bit about this Spanning Tree Protocol
support.

Micrel KSZ8842's 3-port switch and Micrel's other 5-port switches have
port controls to enable/disable tx and rx and stop MAC address learning.
They are supposed to help run STP more efficiently, but somebody needs
to control those ports.

>From my observation of how the brctl application controls the network
devices when running STP, I know the kernel bridge puts all the devices
under it in promiscuous mode and declares the state of each bridge port
associated with the device blocked or forwarding depending on the BPDU
frames received.  When the port is blocked, the device is still active
and passes all frames to the host.  The bridge only looks at BPDU frames
and drops all other frames.  It is better to just shut off the port.

>From the time when the KSZ8842 driver was developed for the Linux 2.4
kernel I looked for a kernel API to tell the bridge port's state so the
device driver can shut off the port if necessary.  I could not find one
and so I came up with this hack to look at the bridge port's structure
directly.  It looks dangerous but is quite safe.  The driver only looks
at the bridge port state variable and finds out the MAC address
associated with the bridge device.  It can get the state definitions
from the if_bridge header.  The private bridge structure may change in
the future and break the code, but as kernel network interfaces are
changing all the time, the driver just needs to be modified for the new
version.  To avoid this situation, the kernel may need to export two
functions to tell the bridge port state and bridge device address and
put the prototypes in the if_bridge header.

Now for the driver implementation for STP support.  I programmed the
switch's static MAC table to always pass the following frames to the
host: BPDU frames with specific multicast address, broadcast frames,
unicast frames with the device bridge's MAC address, and multicast
frames with ICMPv6 multicast address.  All other frames are not passed
to the host and are handled by the switch, forwarding each frame with
its standard forwarding logic.  The port can be shut off if it is
blocked and those frames will not pass through that port.  The host gets
BPDU frames so that the bridge can determine each port's state.  The
other broadcast, unicast, and multicast frames passed to the host are
necessary if some other network devices want to communicate with the
host.  As the forwarding is done by hardware rather than software,
overall performance does increase.

I did verify the driver disables or enables the port appropriately when
the bridge port state changes, but as I do not have the experience of
running a full-scale Spanning Tree, I do not know if this hardware
implementation behaves the same as the software one provided by the
kernel and brctl.  I also did not try using VLAN.
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Powered by blists - more mailing lists