Message-ID: <2d2cb4b6-627a-4e42-bc59-7845bbb6b680@SG2EHSMHS004.ehs.local>
Date:	Mon, 15 Mar 2010 07:40:05 -0600
From:	John Linn <John.Linn@...inx.com>
To:	<michal.simek@...alogix.com>
CC:	<netdev@...r.kernel.org>, <linuxppc-dev@...abs.org>,
	<grant.likely@...retlab.ca>, <jwboyer@...ux.vnet.ibm.com>,
	<john.williams@...alogix.com>, "John Tyner" <jtyner@...ucr.edu>
Subject: RE: [PATCH] [V2] Add non-Virtex5 support for LL TEMAC driver

> -----Original Message-----
> From: Michal Simek [mailto:michal.simek@...alogix.com]
> Sent: Monday, March 15, 2010 2:40 AM
> To: John Linn
> Cc: netdev@...r.kernel.org; linuxppc-dev@...abs.org;
grant.likely@...retlab.ca;
> jwboyer@...ux.vnet.ibm.com; john.williams@...alogix.com; John Tyner
> Subject: Re: [PATCH] [V2] Add non-Virtex5 support for LL TEMAC driver
> 
> John Linn wrote:
> > This patch adds support for using the LL TEMAC Ethernet driver on
> > non-Virtex 5 platforms by adding support for accessing the Soft DMA
> > registers as if they were memory mapped instead of solely through
the
> > DCR's (available on the Virtex 5).
> >
> > The patch also updates the driver so that it runs on the MicroBlaze.
> > The changes were tested on the PowerPC 440, PowerPC 405, and the
> > MicroBlaze platforms.
> 
> Which git-tree have you tested on? (Of course microblaze)

It was tested on the Xilinx tree for MicroBlaze which is based on the
mainline and the Petalogix tree as DMA was needed. I tried to build
against the mainline head but got errors with the DMA routines. I guess
it's possible that it was a configuration issue there as I didn't dig
real deep.

I tested the PowerPC against the head of mainline.

Thanks,
John

> 
> Michal
> 
> >
> > Signed-off-by: John Tyner <jtyner@...ucr.edu>
> > Signed-off-by: John Linn <john.linn@...inx.com>
> > ---
> >
> > V2 - Incorporated comments from Grant and added more logic to allow
the driver
> > to work on MicroBlaze.
> >
> >  drivers/net/Kconfig         |    1 -
> >  drivers/net/ll_temac.h      |   17 +++++-
> >  drivers/net/ll_temac_main.c |  124
++++++++++++++++++++++++++++++++++---------
> >  3 files changed, 113 insertions(+), 29 deletions(-)
> >
> > diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
> > index 9b6efe1..5402105 100644
> > --- a/drivers/net/Kconfig
> > +++ b/drivers/net/Kconfig
> > @@ -2443,7 +2443,6 @@ config MV643XX_ETH
> >  config XILINX_LL_TEMAC
> >  	tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC)
driver"
> >  	select PHYLIB
> > -	depends on PPC_DCR_NATIVE
> >  	help
> >  	  This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
> >  	  core used in Xilinx Spartan and Virtex FPGAs
> > diff --git a/drivers/net/ll_temac.h b/drivers/net/ll_temac.h
> > index 1af66a1..915aa34 100644
> > --- a/drivers/net/ll_temac.h
> > +++ b/drivers/net/ll_temac.h
> > @@ -5,8 +5,11 @@
> >  #include <linux/netdevice.h>
> >  #include <linux/of.h>
> >  #include <linux/spinlock.h>
> > +
> > +#ifdef CONFIG_PPC_DCR
> >  #include <asm/dcr.h>
> >  #include <asm/dcr-regs.h>
> > +#endif
> >
> >  /* packet size info */
> >  #define XTE_HDR_SIZE			14      /* size of
Ethernet header */
> > @@ -290,8 +293,12 @@ This option defaults to enabled (set) */
> >
> >  #define TX_CONTROL_CALC_CSUM_MASK   1
> >
> > +/* Align the IP data in the packet on word boundaries as MicroBlaze
> > + * needs it.
> > + */
> > +
> >  #define XTE_ALIGN       32
> > -#define BUFFER_ALIGN(adr) ((XTE_ALIGN - ((u32) adr)) % XTE_ALIGN)
> > +#define BUFFER_ALIGN(adr) ((34 - ((u32) adr)) % XTE_ALIGN)
> >
> >  #define MULTICAST_CAM_TABLE_NUM 4
> >
> > @@ -335,9 +342,15 @@ struct temac_local {
> >  	struct mii_bus *mii_bus;	/* MII bus reference */
> >  	int mdio_irqs[PHY_MAX_ADDR];	/* IRQs table for MDIO bus */
> >
> > -	/* IO registers and IRQs */
> > +	/* IO registers, dma functions and IRQs */
> >  	void __iomem *regs;
> > +	void __iomem *sdma_regs;
> > +#ifdef CONFIG_PPC_DCR
> >  	dcr_host_t sdma_dcrs;
> > +#endif
> > +	u32 (*dma_in)(struct temac_local *, int);
> > +	void (*dma_out)(struct temac_local *, int, u32);
> > +
> >  	int tx_irq;
> >  	int rx_irq;
> >  	int emac_num;
> > diff --git a/drivers/net/ll_temac_main.c
b/drivers/net/ll_temac_main.c
> > index a18e348..9aedf9b 100644
> > --- a/drivers/net/ll_temac_main.c
> > +++ b/drivers/net/ll_temac_main.c
> > @@ -20,9 +20,6 @@
> >   *   or rx, so this should be okay.
> >   *
> >   * TODO:
> > - * - Fix driver to work on more than just Virtex5.  Right now the
driver
> > - *   assumes that the locallink DMA registers are accessed via DCR
> > - *   instructions.
> >   * - Factor out locallink DMA code into separate driver
> >   * - Fix multicast assignment.
> >   * - Fix support for hardware checksumming.
> > @@ -115,17 +112,86 @@ void temac_indirect_out32(struct temac_local
*lp, int reg, u32 value)
> >  	temac_iow(lp, XTE_CTL0_OFFSET, CNTLREG_WRITE_ENABLE_MASK | reg);
> >  }
> >
> > +/**
> > + * temac_dma_in32 - Memory mapped DMA read, this function expects a
> > + * register input that is based on DCR word addresses which
> > + * are then converted to memory mapped byte addresses
> > + */
> >  static u32 temac_dma_in32(struct temac_local *lp, int reg)
> >  {
> > -	return dcr_read(lp->sdma_dcrs, reg);
> > +	return in_be32((u32 *)(lp->sdma_regs + (reg << 2)));
> >  }
> >
> > +/**
> > + * temac_dma_out32 - Memory mapped DMA read, this function expects
a
> > + * register input that is based on DCR word addresses which
> > + * are then converted to memory mapped byte addresses
> > + */
> >  static void temac_dma_out32(struct temac_local *lp, int reg, u32
value)
> >  {
> > +	out_be32((u32 *)(lp->sdma_regs + (reg << 2)), value);
> > +}
> > +
> > +/* DMA register access functions can be DCR based or memory mapped.
> > + * The PowerPC 440 is DCR based, the PowerPC 405 and MicroBlaze are
both
> > + * memory mapped.
> > + */
> > +#ifdef CONFIG_PPC_DCR
> > +
> > +/**
> > + * temac_dma_dcr_in32 - DCR based DMA read
> > + */
> > +static u32 temac_dma_dcr_in(struct temac_local *lp, int reg)
> > +{
> > +	return dcr_read(lp->sdma_dcrs, reg);
> > +}
> > +
> > +/**
> > + * temac_dma_dcr_out32 - DCR based DMA write
> > + */
> > +static void temac_dma_dcr_out(struct temac_local *lp, int reg, u32
value)
> > +{
> >  	dcr_write(lp->sdma_dcrs, reg, value);
> >  }
> >
> >  /**
> > + * temac_dcr_setup - If the DMA is DCR based, then setup the
address and
> > + * I/O  functions
> > + */
> > +static int temac_dcr_setup(struct temac_local *lp, struct of_device
*op,
> > +				struct device_node *np)
> > +{
> > +	unsigned int dcrs;
> > +
> > +	/* setup the dcr address mapping if it's in the device tree */
> > +
> > +	dcrs = dcr_resource_start(np, 0);
> > +	if (dcrs != 0) {
> > +		lp->sdma_dcrs = dcr_map(np, dcrs, dcr_resource_len(np,
0));
> > +		lp->dma_in = temac_dma_dcr_in;
> > +		lp->dma_out = temac_dma_dcr_out;
> > +		dev_dbg(&op->dev, "DCR base: %x\n", dcrs);
> > +		return 0;
> > +	}
> > +	/* no DCR in the device tree, indicate a failure */
> > +	return -1;
> > +}
> > +
> > +#else
> > +
> > +/*
> > + * temac_dcr_setup - This is a stub for when DCR is not supported,
> > + * such as with MicroBlaze
> > + */
> > +static int temac_dcr_setup(struct temac_local *lp, struct of_device
*op,
> > +				struct device_node *np)
> > +{
> > +	return -1;
> > +}
> > +
> > +#endif
> > +
> > +/**
> >   * temac_dma_bd_init - Setup buffer descriptor rings
> >   */
> >  static int temac_dma_bd_init(struct net_device *ndev)
> > @@ -172,23 +238,23 @@ static int temac_dma_bd_init(struct net_device
*ndev)
> >  		lp->rx_bd_v[i].app0 = STS_CTRL_APP0_IRQONEND;
> >  	}
> >
> > -	temac_dma_out32(lp, TX_CHNL_CTRL, 0x10220400 |
> > +	lp->dma_out(lp, TX_CHNL_CTRL, 0x10220400 |
> >  					  CHNL_CTRL_IRQ_EN |
> >  					  CHNL_CTRL_IRQ_DLY_EN |
> >  					  CHNL_CTRL_IRQ_COAL_EN);
> >  	/* 0x10220483 */
> >  	/* 0x00100483 */
> > -	temac_dma_out32(lp, RX_CHNL_CTRL, 0xff010000 |
> > +	lp->dma_out(lp, RX_CHNL_CTRL, 0xff010000 |
> >  					  CHNL_CTRL_IRQ_EN |
> >  					  CHNL_CTRL_IRQ_DLY_EN |
> >  					  CHNL_CTRL_IRQ_COAL_EN |
> >  					  CHNL_CTRL_IRQ_IOE);
> >  	/* 0xff010283 */
> >
> > -	temac_dma_out32(lp, RX_CURDESC_PTR,  lp->rx_bd_p);
> > -	temac_dma_out32(lp, RX_TAILDESC_PTR,
> > +	lp->dma_out(lp, RX_CURDESC_PTR,  lp->rx_bd_p);
> > +	lp->dma_out(lp, RX_TAILDESC_PTR,
> >  		       lp->rx_bd_p + (sizeof(*lp->rx_bd_v) * (RX_BD_NUM
- 1)));
> > -	temac_dma_out32(lp, TX_CURDESC_PTR, lp->tx_bd_p);
> > +	lp->dma_out(lp, TX_CURDESC_PTR, lp->tx_bd_p);
> >
> >  	return 0;
> >  }
> > @@ -426,9 +492,9 @@ static void temac_device_reset(struct net_device
*ndev)
> >  	temac_indirect_out32(lp, XTE_RXC1_OFFSET, val &
~XTE_RXC1_RXEN_MASK);
> >
> >  	/* Reset Local Link (DMA) */
> > -	temac_dma_out32(lp, DMA_CONTROL_REG, DMA_CONTROL_RST);
> > +	lp->dma_out(lp, DMA_CONTROL_REG, DMA_CONTROL_RST);
> >  	timeout = 1000;
> > -	while (temac_dma_in32(lp, DMA_CONTROL_REG) & DMA_CONTROL_RST) {
> > +	while (lp->dma_in(lp, DMA_CONTROL_REG) & DMA_CONTROL_RST) {
> >  		udelay(1);
> >  		if (--timeout == 0) {
> >  			dev_err(&ndev->dev,
> > @@ -436,7 +502,7 @@ static void temac_device_reset(struct net_device
*ndev)
> >  			break;
> >  		}
> >  	}
> > -	temac_dma_out32(lp, DMA_CONTROL_REG, DMA_TAIL_ENABLE);
> > +	lp->dma_out(lp, DMA_CONTROL_REG, DMA_TAIL_ENABLE);
> >
> >  	temac_dma_bd_init(ndev);
> >
> > @@ -597,7 +663,7 @@ static int temac_start_xmit(struct sk_buff *skb,
struct net_device *ndev)
> >  		lp->tx_bd_tail = 0;
> >
> >  	/* Kick off the transfer */
> > -	temac_dma_out32(lp, TX_TAILDESC_PTR, tail_p); /* DMA start */
> > +	lp->dma_out(lp, TX_TAILDESC_PTR, tail_p); /* DMA start */
> >
> >  	return NETDEV_TX_OK;
> >  }
> > @@ -663,7 +729,7 @@ static void ll_temac_recv(struct net_device
*ndev)
> >  		cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
> >  		bdstat = cur_p->app0;
> >  	}
> > -	temac_dma_out32(lp, RX_TAILDESC_PTR, tail_p);
> > +	lp->dma_out(lp, RX_TAILDESC_PTR, tail_p);
> >
> >  	spin_unlock_irqrestore(&lp->rx_lock, flags);
> >  }
> > @@ -674,8 +740,8 @@ static irqreturn_t ll_temac_tx_irq(int irq, void
*_ndev)
> >  	struct temac_local *lp = netdev_priv(ndev);
> >  	unsigned int status;
> >
> > -	status = temac_dma_in32(lp, TX_IRQ_REG);
> > -	temac_dma_out32(lp, TX_IRQ_REG, status);
> > +	status = lp->dma_in(lp, TX_IRQ_REG);
> > +	lp->dma_out(lp, TX_IRQ_REG, status);
> >
> >  	if (status & (IRQ_COAL | IRQ_DLY))
> >  		temac_start_xmit_done(lp->ndev);
> > @@ -692,8 +758,8 @@ static irqreturn_t ll_temac_rx_irq(int irq, void
*_ndev)
> >  	unsigned int status;
> >
> >  	/* Read and clear the status registers */
> > -	status = temac_dma_in32(lp, RX_IRQ_REG);
> > -	temac_dma_out32(lp, RX_IRQ_REG, status);
> > +	status = lp->dma_in(lp, RX_IRQ_REG);
> > +	lp->dma_out(lp, RX_IRQ_REG, status);
> >
> >  	if (status & (IRQ_COAL | IRQ_DLY))
> >  		ll_temac_recv(lp->ndev);
> > @@ -794,7 +860,7 @@ static ssize_t temac_show_llink_regs(struct
device *dev,
> >  	int i, len = 0;
> >
> >  	for (i = 0; i < 0x11; i++)
> > -		len += sprintf(buf + len, "%.8x%s", temac_dma_in32(lp,
i),
> > +		len += sprintf(buf + len, "%.8x%s", lp->dma_in(lp, i),
> >  			       (i % 8) == 7 ? "\n" : " ");
> >  	len += sprintf(buf + len, "\n");
> >
> > @@ -820,7 +886,6 @@ temac_of_probe(struct of_device *op, const
struct of_device_id *match)
> >  	struct net_device *ndev;
> >  	const void *addr;
> >  	int size, rc = 0;
> > -	unsigned int dcrs;
> >
> >  	/* Init network device structure */
> >  	ndev = alloc_etherdev(sizeof(*lp));
> > @@ -870,13 +935,20 @@ temac_of_probe(struct of_device *op, const
struct of_device_id *match)
> >  		goto nodev;
> >  	}
> >
> > -	dcrs = dcr_resource_start(np, 0);
> > -	if (dcrs == 0) {
> > -		dev_err(&op->dev, "could not get DMA register
address\n");
> > -		goto nodev;
> > +	/* Setup the DMA register accesses, could be DCR or memory
mapped */
> > +	if (temac_dcr_setup(lp, op, np)) {
> > +
> > +		/* no DCR in the device tree, try non-DCR */
> > +		lp->sdma_regs = of_iomap(np, 0);
> > +		if (lp->sdma_regs) {
> > +			lp->dma_in = temac_dma_in32;
> > +			lp->dma_out = temac_dma_out32;
> > +			dev_dbg(&op->dev, "MEM base: %p\n",
lp->sdma_regs);
> > +		} else {
> > +			dev_err(&op->dev, "unable to map DMA
registers\n");
> > +			goto nodev;
> > +		}
> >  	}
> > -	lp->sdma_dcrs = dcr_map(np, dcrs, dcr_resource_len(np, 0));
> > -	dev_dbg(&op->dev, "DCR base: %x\n", dcrs);
> >
> >  	lp->rx_irq = irq_of_parse_and_map(np, 0);
> >  	lp->tx_irq = irq_of_parse_and_map(np, 1);
> 
> 
> --
> Michal Simek, Ing. (M.Eng)
> PetaLogix - Linux Solutions for a Reconfigurable World
> w: www.petalogix.com p: +61-7-30090663,+42-0-721842854 f:
+61-7-30090663


This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately.


--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Powered by blists - more mailing lists