| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <201003311732.59921.matthias.fuchs@esd.eu>
Date: Wed, 31 Mar 2010 17:32:59 +0200
From: Matthias Fuchs <matthias.fuchs@....eu>
To: netdev@...r.kernel.org
Cc: Socketcan-core@...ts.berlios.de
Subject: [PATCH] can: Add esd board support to plx_pci CAN driver
This patch adds support for SJA1000 based PCI CAN interface cards
from electronic system design gmbh.
Two changes have been done on the common code:
- esd boards must not have the 2nd local interupt enabled (PLX9030/9050)
- a new path for PLX9056/PEX8311 chips has been added
In detail the following additional boards are now supported:
CAN-PCI/200 (PCI)
CAN-PCI/266 (PCI)
CAN-PMC266 (PMC module)
CAN-PCIe/2000 (PCI Express)
CAN-CPCI/200 (Compact PCI, 3U)
CAN-PCI104 (PCI104)
Signed-off-by: Matthias Fuchs <matthias.fuchs@....eu>
---
drivers/net/can/sja1000/plx_pci.c | 110 ++++++++++++++++++++++++++++++++++---
1 files changed, 101 insertions(+), 9 deletions(-)
diff --git a/drivers/net/can/sja1000/plx_pci.c b/drivers/net/can/sja1000/plx_pci.c
index 6b46a63..42602e9 100644
--- a/drivers/net/can/sja1000/plx_pci.c
+++ b/drivers/net/can/sja1000/plx_pci.c
@@ -40,7 +40,10 @@ MODULE_DESCRIPTION("Socket-CAN driver for PLX90xx PCI-bridge cards with "
MODULE_SUPPORTED_DEVICE("Adlink PCI-7841/cPCI-7841, "
"Adlink PCI-7841/cPCI-7841 SE, "
"Marathon CAN-bus-PCI, "
- "TEWS TECHNOLOGIES TPMC810");
+ "TEWS TECHNOLOGIES TPMC810, "
+ "esd CAN-PCI/CPCI/PCI104/200, "
+ "esd CAN-PCI/PMC/266, "
+ "esd CAN-PCIe/2000")
MODULE_LICENSE("GPL v2");
#define PLX_PCI_MAX_CHAN 2
@@ -53,7 +56,7 @@ struct plx_pci_card {
#define PLX_PCI_CAN_CLOCK (16000000 / 2)
-/* PLX90xx registers */
+/* PLX9030/9050/9052 registers */
#define PLX_INTCSR 0x4c /* Interrupt Control/Status */
#define PLX_CNTRL 0x50 /* User I/O, Direct Slave Response,
* Serial EEPROM, and Initialization
@@ -65,6 +68,12 @@ struct plx_pci_card {
#define PLX_PCI_INT_EN (1 << 6) /* PCI Interrupt Enable */
#define PLX_PCI_RESET (1 << 30) /* PCI Adapter Software Reset */
+/* PLX9056 registers */
+#define PLX9056_INTCSR 0x68 /* Interrupt Control/Status */
+
+#define PLX9056_LINTI (1 << 11)
+#define PLX9056_PCI_INT_EN (1 << 8)
+
/*
* The board configuration is probably following:
* RX1 is connected to ground.
@@ -100,6 +109,13 @@ struct plx_pci_card {
#define ADLINK_PCI_VENDOR_ID 0x144A
#define ADLINK_PCI_DEVICE_ID 0x7841
+#define ESD_PCI_SUB_SYS_ID_PCI200 0x0004
+#define ESD_PCI_SUB_SYS_ID_PCI266 0x0009
+#define ESD_PCI_SUB_SYS_ID_PMC266 0x000e
+#define ESD_PCI_SUB_SYS_ID_CPCI200 0x010b
+#define ESD_PCI_SUB_SYS_ID_PCIE2000 0x0200
+#define ESD_PCI_SUB_SYS_ID_PCI104200 0x0501
+
#define MARATHON_PCI_DEVICE_ID 0x2715
#define TEWS_PCI_VENDOR_ID 0x1498
@@ -147,6 +163,30 @@ static struct plx_pci_card_info plx_pci_card_info_adlink_se __devinitdata = {
/* based on PLX9052 */
};
+static struct plx_pci_card_info plx_pci_card_info_esd200 __devinitdata = {
+ "esd CAN-PCI/CPCI/PCI104/200", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9030/9050 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_esd266 __devinitdata = {
+ "esd CAN-PCI/PMC/266", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
+ &plx_pci_reset_common
+ /* based on PLX9056 */
+};
+
+static struct plx_pci_card_info plx_pci_card_info_esd2000 __devinitdata = {
+ "esd CAN-PCIe/2000", 2,
+ PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+ {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
+ &plx_pci_reset_common
+ /* based on PEX8311 */
+};
+
static struct plx_pci_card_info plx_pci_card_info_marathon __devinitdata = {
"Marathon CAN-bus-PCI", 2,
PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
@@ -179,6 +219,48 @@ static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl) = {
(kernel_ulong_t)&plx_pci_card_info_adlink_se
},
{
+ /* esd CAN-PCI/200 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI200,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd200
+ },
+ {
+ /* esd CAN-CPCI/200 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_CPCI200,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd200
+ },
+ {
+ /* esd CAN-PCI104/200 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI104200,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd200
+ },
+ {
+ /* esd CAN-PCI/266 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI266,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd266
+ },
+ {
+ /* esd CAN-PMC/266 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PMC266,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd266
+ },
+ {
+ /* esd CAN-PCIE/2000 */
+ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
+ PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCIE2000,
+ 0, 0,
+ (kernel_ulong_t)&plx_pci_card_info_esd2000
+ },
+ {
/* Marathon CAN-bus-PCI card */
PCI_VENDOR_ID_PLX, MARATHON_PCI_DEVICE_ID,
PCI_ANY_ID, PCI_ANY_ID,
@@ -304,10 +386,13 @@ static void plx_pci_del_card(struct pci_dev *pdev)
plx_pci_reset_common(pdev);
/*
- * Disable interrupts from PCI-card (PLX90xx) and disable Local_1,
- * Local_2 interrupts
+ * Disable interrupts from PCI-card and disable local
+ * interrupts
*/
- iowrite32(0x0, card->conf_addr + PLX_INTCSR);
+ if (pdev->device != PCI_DEVICE_ID_PLX_9056)
+ iowrite32(0x0, card->conf_addr + PLX_INTCSR);
+ else
+ iowrite32(0x0, card->conf_addr + PLX9056_INTCSR);
if (card->conf_addr)
pci_iounmap(pdev, card->conf_addr);
@@ -437,10 +522,17 @@ static int __devinit plx_pci_add_card(struct pci_dev *pdev,
* Enable interrupts from PCI-card (PLX90xx) and enable Local_1,
* Local_2 interrupts from the SJA1000 chips
*/
- val = ioread32(card->conf_addr + PLX_INTCSR);
- val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
- iowrite32(val, card->conf_addr + PLX_INTCSR);
-
+ if (pdev->device != PCI_DEVICE_ID_PLX_9056) {
+ val = ioread32(card->conf_addr + PLX_INTCSR);
+ if (pdev->subsystem_vendor == PCI_VENDOR_ID_ESDGMBH)
+ val |= PLX_LINT1_EN | PLX_PCI_INT_EN;
+ else
+ val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
+ iowrite32(val, card->conf_addr + PLX_INTCSR);
+ } else {
+ iowrite32(PLX9056_LINTI | PLX9056_PCI_INT_EN,
+ card->conf_addr + PLX9056_INTCSR);
+ }
return 0;
failure_cleanup:
--
1.6.1
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists