netdev - Re: BUG: IPv6 stops working after a while, needs ip ne del command to reset

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20100817171115.GA4134@mcarlson.broadcom.com>
Date:	Tue, 17 Aug 2010 10:11:15 -0700
From:	"Matt Carlson" <mcarlson@...adcom.com>
To:	"Thomas Habets" <thomas@...ets.pp.se>
cc:	"Eric Dumazet" <eric.dumazet@...il.com>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	netdev <netdev@...r.kernel.org>,
	"Matthew Carlson" <mcarlson@...adcom.com>,
	"Michael Chan" <mchan@...adcom.com>
Subject: Re: BUG: IPv6 stops working after a while, needs ip ne del
 command to reset

On Tue, Aug 17, 2010 at 08:58:26AM -0700, Thomas Habets wrote:
> On Tue, 17 Aug 2010, Eric Dumazet wrote:
> > Try following patch to check tg3 receives correct multicast list (its OK
> > for me, seen on dmesg output)
> >
> > [17162.120238]  add mc_addr(ha->addr=33:33:00:00:00:01)
> > [17162.120270]  add mc_addr(ha->addr=01:00:5e:00:00:01)
> > [17162.120298]  add mc_addr(ha->addr=33:33:ff:87:96:ce)
> > [17162.120326]  add mc_addr(ha->addr=33:33:ff:5c:00:02)
> > [17162.120355] filters=80000001 00000000 00400000 40000000
> 
> Right after boot:
> 
> $ dmesg | egrep 'eth0|^add mc|^filters='
> tg3 0000:03:04.0: eth0: Tigon3 [partno(N/A) rev 9003] (PCIX:133MHz:64-bit) 
> MAC address 00:24:81:a3:44:24
> tg3 0000:03:04.0: eth0: attached PHY is 5714 (10/100/1000Base-T Ethernet) 
> (WireSpeed[1])
> tg3 0000:03:04.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
> tg3 0000:03:04.0: eth0: dma_rwctrl[76148000] dma_mask[40-bit]
> add mc_addr(ha->addr=33:33:00:00:00:01)
> filters=80000000 00000000 00000000 00000000
> add mc_addr(ha->addr=33:33:00:00:00:01)
> filters=80000000 00000000 00000000 00000000
> add mc_addr(ha->addr=33:33:00:00:00:01)
> filters=80000000 00000000 00000000 00000000
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> filters=80000000 00000000 00000000 40000000
> ADDRCONF(NETDEV_UP): eth0: link is not ready
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> filters=80000000 00000000 00000000 40000000
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> filters=80000000 00000000 00000000 40000000
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> add mc_addr(ha->addr=33:33:ff:5c:00:02)
> filters=80000001 00000000 00000000 40000000
> tg3 0000:03:04.0: eth0: Link is up at 1000 Mbps, full duplex
> tg3 0000:03:04.0: eth0: Flow control is off for TX and off for RX
> ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> add mc_addr(ha->addr=33:33:ff:5c:00:02)
> add mc_addr(ha->addr=33:33:ff:a3:44:24)
> filters=80020001 00000000 00000000 40000000
> eth0: no IPv6 routers present
> 
> [ ifconfig eth0 allmulti
>    (ip l and ifconfig say ALLMULTI is on)
> ]
> 
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> add mc_addr(ha->addr=33:33:ff:5c:00:02)
> add mc_addr(ha->addr=33:33:ff:a3:44:24)
> filters=80020001 00000000 00000000 40000000
> 
> [
>    $ sudo ifconfig eth0 -allmulti
>    Warning: Interface eth0 still in ALLMULTI mode.
>    (ip l and ifconfig say ALLMULTI is now off)
> ]
> 
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> add mc_addr(ha->addr=33:33:ff:5c:00:02)
> add mc_addr(ha->addr=33:33:ff:a3:44:24)
> filters=80020001 00000000 00000000 40000000
> 
> [ ifconfig eth0 allmulti
>    (same effect)
> ]
> 
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> add mc_addr(ha->addr=33:33:ff:5c:00:02)
> add mc_addr(ha->addr=33:33:ff:a3:44:24)
> filters=80020001 00000000 00000000 40000000
> 
> [
>    $ sudo ifconfig eth0 -allmulti
>    Warning: Interface eth0 still in ALLMULTI mode.
>    (same effect)
> ]
> 
> add mc_addr(ha->addr=33:33:00:00:00:01)
> add mc_addr(ha->addr=01:00:5e:00:00:01)
> add mc_addr(ha->addr=33:33:ff:5c:00:02)
> add mc_addr(ha->addr=33:33:ff:a3:44:24)
> filters=80020001 00000000 00000000 40000000
> 
> 
> > But if problem remains even with "ifconfig eth0 allmulti" I suspect a
> > NIC firmware problem. (allmulti set to 1 all the 128 bits of filters)

I suspect Eric is right.

Thomas, can you give me the output of 'ethtool -i eth0'?

> If you expected more bits set in "filters" with allmulti than without it, 
> that doesn't seem to be the case.

"allmulti" has the effect of enabling all 128 bits of the multicast hash
filters.  It doesn't explicitly enable them all though.

> Applied your patch to v2.6.35.
> 
> ---------
> typedef struct me_s {
>    char name[]      = { "Thomas Habets" };
>    char email[]     = { "thomas@...ets.pp.se" };
>    char kernel[]    = { "Linux" };
>    char *pgpKey[]   = { "http://www.habets.pp.se/pubkey.txt" };
>    char pgp[] = { "A8A3 D1DD 4AE0 8467 7FDE  0945 286A E90A AD48 E854" };
>    char coolcmd[]   = { "echo '. ./_&. ./_'>_;. ./_" };
> } me_t;
> 

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html