| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <201009010048.44644.linux@rainbow-software.org> Date: Wed, 1 Sep 2010 00:48:41 +0200 From: Ondrej Zary <linux@...nbow-software.org> To: Simon Arlott <simon@...e.lp0.eu> Cc: accessrunner-general@...ts.sourceforge.net, netdev@...r.kernel.org, Kernel development list <linux-kernel@...r.kernel.org> Subject: Re: cxacru: USB ethernet port of CX82310-based ADSL routers? On Wednesday 01 September 2010 00:15:49 Simon Arlott wrote: > On 31/08/10 22:13, Ondrej Zary wrote: > > Hello, > > I have an ADSL router based on Conexant CX82310 chip. This chip provides > > both ethernet and USB interfaces. The ethernet interface is often > > internally connected to a 5-port switch (in my case too). The USB > > interface works as an ethernet card in Windows (using proprietary > > driver). In Linux, the cxacru driver binds to the device but does not > > work (no wonder - it's doing firmware things in an attempt to bring an > > ADSL modem up). > > > > I captured a log from Windows (device connect, DHCP and disconnect): > > http://www.rainbow-software.org/linux_files/cx82310/cx-run-dhcp.log > > > > The commands seem to match the enums in cxacru > > driver (and go to endpoint 1): > > 0x84, 0x85, 0x90, 0x91, 0x92, 0x99 (unknown) > > Data goes to/from endpoint 2 as ethernet frames (with something at the > > beginning). > > > > I wonder how to implement support for this device in cxacru driver. Or > > would be a separate driver better? > > Support for this shouldn't really go into the cxacru driver, as that's > for an USB ATM interface (it depends on usbatm for actual ATM traffic) > not ethernet. That's what I was afraid of... > Unfortunately it doesn't look like a trivial task to auto-detect which > driver should handle it... your device itself claims to be an "ADSL > Modem". In fact, it does not. The idProduct text is from usb.ids file (which is often incorrect). The device says that it's "USB NET CARD" (iProduct). But I don't know if Linux can match drivers by iProduct string. > You'd need to know what type of device it was before loading the > firmware, which would further complicate auto-detection as some custom > firmware may be required that attempts to probe the device and then > accepts new firmware. I have no way of testing this on all the types of > existing hardware: http://accessrunner.sourceforge.net/modems.shtml > > Does it happen to work as an ADSL modem too if you load the right > firmware? > d275d0fef591e2233654ea591eccb0d15211eb82 cxacru-fw.bin 624192 > > There should be some flash memory you could try reading, however it > may not contain anything useful. > > See "commands for interaction with the flash memory" in cxacru.c and > http://simon.arlott.org/pub/cxacru/raw.c Thanks, I'll try that, although I doubt that it will help. > One possibility is to rewrite the flash to indicate that it's an > ethernet class device, or just handle class 255 differently. It would > be interesting to know what the windows driver does when the device > class is changed. (I don't know which bytes in the flash memory > correspond to that value as mine are all 00, hopefully if you can read > yours you'll have an FF in that area.) > > Ignoring 0572:cb01 class 255 in the cxacru probe function would be an > option... but I don't know how many existing users that would affect. Maybe ignoring the device if class is 255 and iProduct is "USB NET CARD" (or does not contain "MODEM"?). > > lsusb output: > > > > Bus 001 Device 003: ID 0572:cb01 Conexant Systems (Rockwell), Inc. > > GeekADSL Promax Q31 ADSL Modem Device Descriptor: > > bLength 18 > > bDescriptorType 1 > > bcdUSB 1.10 > > bDeviceClass 255 Vendor Specific Class > > bDeviceSubClass 0 > > bDeviceProtocol 0 > > bMaxPacketSize0 64 > > idVendor 0x0572 Conexant Systems (Rockwell), Inc. > > idProduct 0xcb01 GeekADSL Promax Q31 ADSL Modem This is from usb.ids ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ (random string entered by someone on the internet) > > bcdDevice 1.00 > > iManufacturer 1 - > > iProduct 2 USB NET CARD This is from the device ^^^^^^^^^^^^ > > iSerial 3 00000060 > > bNumConfigurations 1 > > Configuration Descriptor: > > bLength 9 > > bDescriptorType 2 > > wTotalLength 67 > > bNumInterfaces 1 > > bConfigurationValue 1 > > iConfiguration 0 > > bmAttributes 0xc0 > > Self Powered > > MaxPower 80mA > > Interface Descriptor: > > bLength 9 > > bDescriptorType 4 > > bInterfaceNumber 0 > > bAlternateSetting 0 > > bNumEndpoints 7 > > bInterfaceClass 0 (Defined at Interface level) > > bInterfaceSubClass 0 > > bInterfaceProtocol 0 > > iInterface 0 > > Endpoint Descriptor: > > bLength 7 > > bDescriptorType 5 > > bEndpointAddress 0x81 EP 1 IN > > bmAttributes 3 > > Transfer Type Interrupt > > Synch Type None > > Usage Type Data > > wMaxPacketSize 0x0040 1x 64 bytes > > bInterval 4 > > Endpoint Descriptor: > > bLength 7 > > bDescriptorType 5 > > bEndpointAddress 0x01 EP 1 OUT > > bmAttributes 3 > > Transfer Type Interrupt > > Synch Type None > > Usage Type Data > > wMaxPacketSize 0x0040 1x 64 bytes > > bInterval 4 > > Endpoint Descriptor: > > bLength 7 > > bDescriptorType 5 > > bEndpointAddress 0x82 EP 2 IN > > bmAttributes 2 > > Transfer Type Bulk > > Synch Type None > > Usage Type Data > > wMaxPacketSize 0x0040 1x 64 bytes > > bInterval 1 > > Endpoint Descriptor: > > bLength 7 > > bDescriptorType 5 > > bEndpointAddress 0x02 EP 2 OUT > > bmAttributes 2 > > Transfer Type Bulk > > Synch Type None > > Usage Type Data > > wMaxPacketSize 0x0040 1x 64 bytes > > bInterval 1 > > Endpoint Descriptor: > > bLength 7 > > bDescriptorType 5 > > bEndpointAddress 0x83 EP 3 IN > > bmAttributes 2 > > Transfer Type Bulk > > Synch Type None > > Usage Type Data > > wMaxPacketSize 0x0040 1x 64 bytes > > bInterval 1 > > Endpoint Descriptor: > > bLength 7 > > bDescriptorType 5 > > bEndpointAddress 0x03 EP 3 OUT > > bmAttributes 2 > > Transfer Type Bulk > > Synch Type None > > Usage Type Data > > wMaxPacketSize 0x0040 1x 64 bytes > > bInterval 1 > > Endpoint Descriptor: > > bLength 7 > > bDescriptorType 5 > > bEndpointAddress 0x84 EP 4 IN > > bmAttributes 3 > > Transfer Type Interrupt > > Synch Type None > > Usage Type Data > > wMaxPacketSize 0x0008 1x 8 bytes > > bInterval 4 > > Device Status: 0x0001 > > Self Powered > > The three versions of the hardware I have are below: > > Bus 002 Device 002: ID 0572:cafe Conexant Systems (Rockwell), Inc. > AccessRunner ADSL Modem Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 64 > idVendor 0x0572 Conexant Systems (Rockwell), Inc. > idProduct 0xcafe AccessRunner ADSL Modem > bcdDevice 0.01 > iManufacturer 1 - > iProduct 2 ADSL USB MODEM > iSerial 3 28217989 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 67 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xa0 > (Bus Powered) > Remote Wakeup > MaxPower 500mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 7 > bInterfaceClass 0 (Defined at Interface level) > bInterfaceSubClass 0 > bInterfaceProtocol 0 > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x01 EP 1 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x82 EP 2 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x02 EP 2 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x03 EP 3 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x84 EP 4 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0008 1x 8 bytes > bInterval 200 > Device Status: 0x0001 > Self Powered > > Bus 002 Device 002: ID 0eb0:3457 > Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 64 > idVendor 0x0eb0 > idProduct 0x3457 > bcdDevice 90.06 > iManufacturer 1 - > iProduct 2 ADSL USB MODEM > iSerial 3 08298061 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 67 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0xa0 > (Bus Powered) > Remote Wakeup > MaxPower 500mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 7 > bInterfaceClass 0 (Defined at Interface level) > bInterfaceSubClass 0 > bInterfaceProtocol 0 > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x01 EP 1 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x82 EP 2 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x02 EP 2 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x03 EP 3 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x84 EP 4 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0008 1x 8 bytes > bInterval 200 > Device Status: 0x0001 > Self Powered > > Bus 002 Device 005: ID 0572:cb00 Conexant Systems (Rockwell), Inc. E-Tech > ADSL Modem v2 Device Descriptor: > bLength 18 > bDescriptorType 1 > bcdUSB 1.10 > bDeviceClass 0 (Defined at Interface level) > bDeviceSubClass 0 > bDeviceProtocol 0 > bMaxPacketSize0 64 > idVendor 0x0572 Conexant Systems (Rockwell), Inc. > idProduct 0xcb00 E-Tech ADSL Modem v2 > bcdDevice 0.01 > iManufacturer 1 - > iProduct 2 ADSL USB MODEM > iSerial 3 08298061 > bNumConfigurations 1 > Configuration Descriptor: > bLength 9 > bDescriptorType 2 > wTotalLength 67 > bNumInterfaces 1 > bConfigurationValue 1 > iConfiguration 0 > bmAttributes 0x80 > (Bus Powered) > MaxPower 500mA > Interface Descriptor: > bLength 9 > bDescriptorType 4 > bInterfaceNumber 0 > bAlternateSetting 0 > bNumEndpoints 7 > bInterfaceClass 0 (Defined at Interface level) > bInterfaceSubClass 0 > bInterfaceProtocol 0 > iInterface 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x81 EP 1 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x01 EP 1 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x82 EP 2 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x02 EP 2 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x83 EP 3 IN > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x03 EP 3 OUT > bmAttributes 2 > Transfer Type Bulk > Synch Type None > Usage Type Data > wMaxPacketSize 0x0040 1x 64 bytes > bInterval 0 > Endpoint Descriptor: > bLength 7 > bDescriptorType 5 > bEndpointAddress 0x84 EP 4 IN > bmAttributes 3 > Transfer Type Interrupt > Synch Type None > Usage Type Data > wMaxPacketSize 0x0008 1x 8 bytes > bInterval 200 > Device Status: 0x0001 > Self Powered All these devices seem to use bDeviceClass 0 and iProduct "ADSL USB MODEM". -- Ondrej Zary -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists