netdev - [RFD PATCH] netdev/phy/of: Augment device tree bindings for PHYs to specify IEEE802.3-2005 Section 45 addressing.

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [day] [month] [year] [list]

Message-Id: <1317424182-29252-1-git-send-email-david.daney@cavium.com>
Date:	Fri, 30 Sep 2011 16:09:42 -0700
From:	David Daney <david.daney@...ium.com>
To:	devicetree-discuss@...ts.ozlabs.org, grant.likely@...retlab.ca,
	linux-kernel@...r.kernel.org, netdev@...r.kernel.org,
	davem@...emloft.net
Cc:	David Daney <david.daney@...ium.com>
Subject: [RFD PATCH] netdev/phy/of: Augment device tree bindings for PHYs to specify IEEE802.3-2005 Section 45 addressing.

Many 10 gigabit Ethernet PHY devices are interfaced to the MDIO bus
using a protocol called IEEE802.3-2005 Section 45.  Where as PHYS for
1G, 100M and 10M usually use IEEE802.3-2005 Section 22.  These two
protocols can be present on the same MDIO bus.

If we look at the Linux PHY probing code in drivers/of/of_mdio.c and
drivers/net/phy/phy_device.c, we have the situation where we need to
read the PHY registers to get the PHY ID out so that we can use this
to bind to a compatible driver.  However we can only read these
registers if we know the proper MDIO bus protocol to use.

My idea is as follows:

o Add an optional property "mdio-clause-45" to the PHY's device tree
  node to indicate that clause 45 addressing is used.

o When calling get_phy_id() we will set MII_ADDR_C45 in the address
  if we know that clause 45 addressing is required for the PHY.
  get_phy_id() will then use the proper bus protocol and register
  numbers to read PHY ID based on MII_ADDR_C45.

o of_mdiobus_register() will signal MII_ADDR_C45 for PHYs tagged with
  "mdio-clause-45"

o Existing PHYs without "mdio-clause-45" are unaffected.

o If no specific driver for the probed PHY ID is present, we can still
  communicate with the PHY and perhaps use a generic 10G phy driver.
  If the MDIO bus protocol were just to depend on the "compatible"
  property, then we could not use generic drivers for unknown PHY IDs

Comments/other ideas welcome.

Thanks,

Signed-off-by: David Daney <david.daney@...ium.com>
---
 Documentation/devicetree/bindings/net/phy.txt |    5 +++++
 1 files changed, 5 insertions(+), 0 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index bb8c742..69fd948 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -14,6 +14,11 @@ Required properties:
  - linux,phandle :  phandle for this node; likely referenced by an
    ethernet controller node.

+Optional properties:
+
+ - mdio-clause-45 : Optional.  If present, IEEE802.3-2005 Section 45
+   protocol is used for register access (usually for 10G PHYs).
+
 Example:

 ethernet-phy@0 {
-- 
1.7.2.3

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html