| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1336854637-6708-2-git-send-email-jeffrey.t.kirsher@intel.com>
Date: Sat, 12 May 2012 13:30:36 -0700
From: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
To: davem@...emloft.net
Cc: Carolyn Wyborny <carolyn.wyborny@...el.com>,
netdev@...r.kernel.org, gospo@...hat.com, sassmann@...hat.com,
Jeff Kirsher <jeffrey.t.kirsher@...el.com>
Subject: [net-next 1/2] igb: Add function and pointers for 82580 low power state settings.
From: Carolyn Wyborny <carolyn.wyborny@...el.com>
82580 and later parts did not have low power setting functions. This patch
adds the specific functions, pointers and assignments for these low
power settings.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@...el.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@...el.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
---
drivers/net/ethernet/intel/igb/e1000_82575.c | 94 ++++++++++++++++++++++++++
drivers/net/ethernet/intel/igb/e1000_phy.h | 7 ++
2 files changed, 101 insertions(+), 0 deletions(-)
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c
index 08bdc33..b945992 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.c
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
@@ -52,6 +52,8 @@ static s32 igb_write_phy_reg_82580(struct e1000_hw *, u32, u16);
static s32 igb_reset_hw_82575(struct e1000_hw *);
static s32 igb_reset_hw_82580(struct e1000_hw *);
static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *, bool);
+static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *, bool);
+static s32 igb_set_d3_lplu_state_82580(struct e1000_hw *, bool);
static s32 igb_setup_copper_link_82575(struct e1000_hw *);
static s32 igb_setup_serdes_link_82575(struct e1000_hw *);
static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16);
@@ -359,6 +361,8 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_82580;
phy->ops.get_cable_length = igb_get_cable_length_82580;
phy->ops.get_phy_info = igb_get_phy_info_82580;
+ phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580;
+ phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state_82580;
break;
default:
return -E1000_ERR_PHY;
@@ -674,6 +678,96 @@ out:
}
/**
+ * igb_set_d0_lplu_state_82580 - Set Low Power Linkup D0 state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU D0 state according to the active flag. When
+ * activating LPLU this function also disables smart speed
+ * and vice versa. LPLU will not be activated unless the
+ * device autonegotiation advertisement meets standards of
+ * either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 data;
+
+ data = rd32(E1000_82580_PHY_POWER_MGMT);
+
+ if (active) {
+ data |= E1000_82580_PM_D0_LPLU;
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ data &= ~E1000_82580_PM_SPD;
+ } else {
+ data &= ~E1000_82580_PM_D0_LPLU;
+
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on)
+ data |= E1000_82580_PM_SPD;
+ else if (phy->smart_speed == e1000_smart_speed_off)
+ data &= ~E1000_82580_PM_SPD; }
+
+ wr32(E1000_82580_PHY_POWER_MGMT, data);
+ return ret_val;
+}
+
+/**
+ * igb_set_d3_lplu_state_82580 - Sets low power link up state for D3
+ * @hw: pointer to the HW structure
+ * @active: boolean used to enable/disable lplu
+ *
+ * Success returns 0, Failure returns 1
+ *
+ * The low power link up (lplu) state is set to the power management level D3
+ * and SmartSpeed is disabled when active is true, else clear lplu for D3
+ * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU
+ * is used during Dx states where the power conservation is most important.
+ * During driver activity, SmartSpeed should be enabled so performance is
+ * maintained.
+ **/
+s32 igb_set_d3_lplu_state_82580(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 data;
+
+ data = rd32(E1000_82580_PHY_POWER_MGMT);
+
+ if (!active) {
+ data &= ~E1000_82580_PM_D3_LPLU;
+ /*
+ * LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on)
+ data |= E1000_82580_PM_SPD;
+ else if (phy->smart_speed == e1000_smart_speed_off)
+ data &= ~E1000_82580_PM_SPD;
+ } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
+ (phy->autoneg_advertised == E1000_ALL_NOT_GIG) ||
+ (phy->autoneg_advertised == E1000_ALL_10_SPEED)) {
+ data |= E1000_82580_PM_D3_LPLU;
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ data &= ~E1000_82580_PM_SPD;
+ }
+
+ wr32(E1000_82580_PHY_POWER_MGMT, data);
+ return ret_val;
+}
+
+/**
* igb_acquire_nvm_82575 - Request for access to EEPROM
* @hw: pointer to the HW structure
*
diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.h b/drivers/net/ethernet/intel/igb/e1000_phy.h
index 4c32ac6..84172ea 100644
--- a/drivers/net/ethernet/intel/igb/e1000_phy.h
+++ b/drivers/net/ethernet/intel/igb/e1000_phy.h
@@ -114,6 +114,13 @@ s32 igb_get_cable_length_82580(struct e1000_hw *hw);
/* I82580 PHY Diagnostics Status */
#define I82580_DSTATUS_CABLE_LENGTH 0x03FC
#define I82580_DSTATUS_CABLE_LENGTH_SHIFT 2
+
+/* 82580 PHY Power Management */
+#define E1000_82580_PHY_POWER_MGMT 0xE14
+#define E1000_82580_PM_SPD 0x0001 /* Smart Power Down */
+#define E1000_82580_PM_D0_LPLU 0x0002 /* For D0a states */
+#define E1000_82580_PM_D3_LPLU 0x0004 /* For all other states */
+
/* Enable flexible speed on link-up */
#define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */
#define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */
--
1.7.7.6
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists