| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1342765524-29711-2-git-send-email-jeffrey.t.kirsher@intel.com>
Date: Thu, 19 Jul 2012 23:25:24 -0700
From: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
To: bhutchings@...arflare.com
Cc: Jesse Brandeburg <jesse.brandeburg@...el.com>,
netdev@...r.kernel.org, davem@...emloft.net,
Jeff Kirsher <jeffrey.t.kirsher@...el.com>
Subject: [ethtool 2/2] ethtool: allow setting MDI-X state
From: Jesse Brandeburg <jesse.brandeburg@...el.com>
A bit ago ethtool added support for reading MDI-X state, this
patch finishes the implementation, adding the complementary write
command.
Add support to ethtool for controlling the MDI-X (crossover)
state of a network port. Most adapters correctly negotiate
MDI-X, but some ill-behaved switches have trouble and end up
picking the wrong MDI setting, which results in complete loss of
link. Usually this error condition can be observed when multiple
ethtool -r ethX are required before link is achieved.
This patch allows the user to override the normal "auto" setting
and force the crossover state to on or off.
The set will fail if the driver doesn't support the get, as
suggested by Ben Hutchings. Unfortunately there is no way to
tell the set isn't supported *if* the driver supports the get,
set just silently fails.
# ./ethtool -s p1p1 mdix off
setting MDI not supported
usage is ethtool -s eth0 mdix [auto|on|off]
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@...el.com>
Tested-by: Aaron Brown <aaron.f.brown@...el.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
---
ethtool.8.in | 8 ++++++++
ethtool.c | 26 ++++++++++++++++++++++++++
2 files changed, 34 insertions(+)
diff --git a/ethtool.8.in b/ethtool.8.in
index ff3255b..44943a2 100644
--- a/ethtool.8.in
+++ b/ethtool.8.in
@@ -229,6 +229,7 @@ ethtool \- query or control network driver and hardware settings
.BI speed \ N
.B2 duplex half full
.B4 port tp aui bnc mii fibre
+.B3 mdix auto on off
.B2 autoneg on off
.BN advertise
.BN phyad
@@ -521,6 +522,13 @@ Sets full or half duplex mode.
.A4 port tp aui bnc mii fibre
Selects device port.
.TP
+.A3 mdix auto on off
+Selects MDI-X mode for port. May be used to override the automatic detection
+feature of most adapters. Auto means automatic detection of MDI status, on
+forces MDI-X (crossover) mode, while off means MDI (straight through) mode.
+The driver should guarantee that this command takes effect immediately, and
+if necessary may reset the link to cause the change to take effect.
+.TP
.A2 autoneg on off
Specifies whether autonegotiation should be enabled. Autonegotiation
is enabled by default, but in some network devices may have trouble
diff --git a/ethtool.c b/ethtool.c
index e573357..9effc60 100644
--- a/ethtool.c
+++ b/ethtool.c
@@ -18,6 +18,8 @@
* Rx Network Flow Control configuration support <santwona.behera@....com>
* Various features by Ben Hutchings <bhutchings@...arflare.com>;
* Copyright 2009, 2010 Solarflare Communications
+ * MDI-X set support by Jesse Brandeburg <jesse.brandeburg@...el.com>
+ * Copyright 2012 Intel Corporation
*
* TODO:
* * show settings for all devices
@@ -2199,6 +2201,7 @@ static int do_sset(struct cmd_context *ctx)
int speed_wanted = -1;
int duplex_wanted = -1;
int port_wanted = -1;
+ int mdix_wanted = -1;
int autoneg_wanted = -1;
int phyad_wanted = -1;
int xcvr_wanted = -1;
@@ -2259,6 +2262,19 @@ static int do_sset(struct cmd_context *ctx)
port_wanted = PORT_FIBRE;
else
exit_bad_args();
+ } else if (!strcmp(argp[i], "mdix")) {
+ gset_changed = 1;
+ i += 1;
+ if (i >= argc)
+ exit_bad_args();
+ if (!strcmp(argp[i], "auto"))
+ mdix_wanted = ETH_TP_MDI_AUTO;
+ else if (!strcmp(argp[i], "on"))
+ mdix_wanted = ETH_TP_MDI_X;
+ else if (!strcmp(argp[i], "off"))
+ mdix_wanted = ETH_TP_MDI;
+ else
+ exit_bad_args();
} else if (!strcmp(argp[i], "autoneg")) {
i += 1;
if (i >= argc)
@@ -2380,6 +2396,13 @@ static int do_sset(struct cmd_context *ctx)
ecmd.duplex = duplex_wanted;
if (port_wanted != -1)
ecmd.port = port_wanted;
+ if (mdix_wanted != -1) {
+ /* check driver supports MDI-X */
+ if (ecmd.eth_tp_mdix != ETH_TP_MDI_INVALID)
+ ecmd.eth_tp_mdix_ctrl = mdix_wanted;
+ else
+ fprintf(stderr, "setting MDI not supported\n");
+ }
if (autoneg_wanted != -1)
ecmd.autoneg = autoneg_wanted;
if (phyad_wanted != -1)
@@ -2439,6 +2462,8 @@ static int do_sset(struct cmd_context *ctx)
fprintf(stderr, " not setting phy_address\n");
if (xcvr_wanted != -1)
fprintf(stderr, " not setting transceiver\n");
+ if (mdix_wanted != -1)
+ fprintf(stderr, " not setting mdix\n");
}
}
@@ -3604,6 +3629,7 @@ static const struct option {
" [ speed %d ]\n"
" [ duplex half|full ]\n"
" [ port tp|aui|bnc|mii|fibre ]\n"
+ " [ mdix auto|on|off ]\n"
" [ autoneg on|off ]\n"
" [ advertise %x ]\n"
" [ phyad %d ]\n"
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists