| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1369173800-20326-7-git-send-email-jeffrey.t.kirsher@intel.com>
Date: Tue, 21 May 2013 15:03:14 -0700
From: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
To: davem@...emloft.net
Cc: "Akeem G. Abodunrin" <akeem.g.abodunrin@...el.com>,
netdev@...r.kernel.org, gospo@...hat.com, sassmann@...hat.com,
Carolyn Wyborny <carolyn.wyborny@...el.com>,
Jeff Kirsher <jeffrey.t.kirsher@...el.com>
Subject: [net-next 06/12] igb: Support for SFP modules discovery
From: "Akeem G. Abodunrin" <akeem.g.abodunrin@...el.com>
This patch adds support for SFP modules media type discovery for
SGMII, which will enable driver to detect supported external PHYs,
including 100baseFXSFP module.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@...el.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@...el.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
---
drivers/net/ethernet/intel/igb/e1000_82575.c | 120 +++++++++++++++++++++++-
drivers/net/ethernet/intel/igb/e1000_defines.h | 30 +++---
drivers/net/ethernet/intel/igb/e1000_hw.h | 2 +
drivers/net/ethernet/intel/igb/e1000_phy.c | 124 +++++++++++++++++++++++++
drivers/net/ethernet/intel/igb/e1000_phy.h | 20 ++++
drivers/net/ethernet/intel/igb/igb_ethtool.c | 34 +++----
6 files changed, 291 insertions(+), 39 deletions(-)
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c
index ff6a17c..f21a91a 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.c
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
@@ -401,12 +401,82 @@ static s32 igb_init_mac_params_82575(struct e1000_hw *hw)
return 0;
}
+/**
+ * igb_set_sfp_media_type_82575 - derives SFP module media type.
+ * @hw: pointer to the HW structure
+ *
+ * The media type is chosen based on SFP module.
+ * compatibility flags retrieved from SFP ID EEPROM.
+ **/
+static s32 igb_set_sfp_media_type_82575(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_ERR_CONFIG;
+ u32 ctrl_ext = 0;
+ struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+ struct e1000_sfp_flags *eth_flags = &dev_spec->eth_flags;
+ u8 tranceiver_type = 0;
+ s32 timeout = 3;
+
+ /* Turn I2C interface ON and power on sfp cage */
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
+ wr32(E1000_CTRL_EXT, ctrl_ext | E1000_CTRL_I2C_ENA);
+
+ wrfl();
+
+ /* Read SFP module data */
+ while (timeout) {
+ ret_val = igb_read_sfp_data_byte(hw,
+ E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_IDENTIFIER_OFFSET),
+ &tranceiver_type);
+ if (ret_val == 0)
+ break;
+ msleep(100);
+ timeout--;
+ }
+ if (ret_val != 0)
+ goto out;
+
+ ret_val = igb_read_sfp_data_byte(hw,
+ E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_ETH_FLAGS_OFFSET),
+ (u8 *)eth_flags);
+ if (ret_val != 0)
+ goto out;
+
+ /* Check if there is some SFP module plugged and powered */
+ if ((tranceiver_type == E1000_SFF_IDENTIFIER_SFP) ||
+ (tranceiver_type == E1000_SFF_IDENTIFIER_SFF)) {
+ dev_spec->module_plugged = true;
+ if (eth_flags->e1000_base_lx || eth_flags->e1000_base_sx) {
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ } else if (eth_flags->e100_base_fx) {
+ dev_spec->sgmii_active = true;
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ } else if (eth_flags->e1000_base_t) {
+ dev_spec->sgmii_active = true;
+ hw->phy.media_type = e1000_media_type_copper;
+ } else {
+ hw->phy.media_type = e1000_media_type_unknown;
+ hw_dbg("PHY module has not been recognized\n");
+ goto out;
+ }
+ } else {
+ hw->phy.media_type = e1000_media_type_unknown;
+ }
+ ret_val = 0;
+out:
+ /* Restore I2C interface setting */
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+ return ret_val;
+}
+
static s32 igb_get_invariants_82575(struct e1000_hw *hw)
{
struct e1000_mac_info *mac = &hw->mac;
struct e1000_dev_spec_82575 * dev_spec = &hw->dev_spec._82575;
s32 ret_val;
u32 ctrl_ext = 0;
+ u32 link_mode = 0;
switch (hw->device_id) {
case E1000_DEV_ID_82575EB_COPPER:
@@ -470,16 +540,56 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
*/
hw->phy.media_type = e1000_media_type_copper;
dev_spec->sgmii_active = false;
+ dev_spec->module_plugged = false;
ctrl_ext = rd32(E1000_CTRL_EXT);
- switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
- case E1000_CTRL_EXT_LINK_MODE_SGMII:
- dev_spec->sgmii_active = true;
- break;
+
+ link_mode = ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK;
+ switch (link_mode) {
case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
- case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
hw->phy.media_type = e1000_media_type_internal_serdes;
break;
+ case E1000_CTRL_EXT_LINK_MODE_SGMII:
+ /* Get phy control interface type set (MDIO vs. I2C)*/
+ if (igb_sgmii_uses_mdio_82575(hw)) {
+ hw->phy.media_type = e1000_media_type_copper;
+ dev_spec->sgmii_active = true;
+ break;
+ }
+ /* fall through for I2C based SGMII */
+ case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
+ /* read media type from SFP EEPROM */
+ ret_val = igb_set_sfp_media_type_82575(hw);
+ if ((ret_val != 0) ||
+ (hw->phy.media_type == e1000_media_type_unknown)) {
+ /* If media type was not identified then return media
+ * type defined by the CTRL_EXT settings.
+ */
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+
+ if (link_mode == E1000_CTRL_EXT_LINK_MODE_SGMII) {
+ hw->phy.media_type = e1000_media_type_copper;
+ dev_spec->sgmii_active = true;
+ }
+
+ break;
+ }
+
+ /* do not change link mode for 100BaseFX */
+ if (dev_spec->eth_flags.e100_base_fx)
+ break;
+
+ /* change current link mode setting */
+ ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
+
+ if (hw->phy.media_type == e1000_media_type_copper)
+ ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII;
+ else
+ ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
+
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+
+ break;
default:
break;
}
diff --git a/drivers/net/ethernet/intel/igb/e1000_defines.h b/drivers/net/ethernet/intel/igb/e1000_defines.h
index aa17649..aa201ab 100644
--- a/drivers/net/ethernet/intel/igb/e1000_defines.h
+++ b/drivers/net/ethernet/intel/igb/e1000_defines.h
@@ -61,20 +61,22 @@
/* Clear Interrupt timers after IMS clear */
/* packet buffer parity error detection enabled */
/* descriptor FIFO parity error detection enable */
-#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
-#define E1000_I2CCMD_REG_ADDR_SHIFT 16
-#define E1000_I2CCMD_PHY_ADDR_SHIFT 24
-#define E1000_I2CCMD_OPCODE_READ 0x08000000
-#define E1000_I2CCMD_OPCODE_WRITE 0x00000000
-#define E1000_I2CCMD_READY 0x20000000
-#define E1000_I2CCMD_ERROR 0x80000000
-#define E1000_MAX_SGMII_PHY_REG_ADDR 255
-#define E1000_I2CCMD_PHY_TIMEOUT 200
-#define E1000_IVAR_VALID 0x80
-#define E1000_GPIE_NSICR 0x00000001
-#define E1000_GPIE_MSIX_MODE 0x00000010
-#define E1000_GPIE_EIAME 0x40000000
-#define E1000_GPIE_PBA 0x80000000
+#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
+#define E1000_I2CCMD_REG_ADDR_SHIFT 16
+#define E1000_I2CCMD_PHY_ADDR_SHIFT 24
+#define E1000_I2CCMD_OPCODE_READ 0x08000000
+#define E1000_I2CCMD_OPCODE_WRITE 0x00000000
+#define E1000_I2CCMD_READY 0x20000000
+#define E1000_I2CCMD_ERROR 0x80000000
+#define E1000_I2CCMD_SFP_DATA_ADDR(a) (0x0000 + (a))
+#define E1000_I2CCMD_SFP_DIAG_ADDR(a) (0x0100 + (a))
+#define E1000_MAX_SGMII_PHY_REG_ADDR 255
+#define E1000_I2CCMD_PHY_TIMEOUT 200
+#define E1000_IVAR_VALID 0x80
+#define E1000_GPIE_NSICR 0x00000001
+#define E1000_GPIE_MSIX_MODE 0x00000010
+#define E1000_GPIE_EIAME 0x40000000
+#define E1000_GPIE_PBA 0x80000000
/* Receive Descriptor bit definitions */
#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
diff --git a/drivers/net/ethernet/intel/igb/e1000_hw.h b/drivers/net/ethernet/intel/igb/e1000_hw.h
index 488abb2..94d7866 100644
--- a/drivers/net/ethernet/intel/igb/e1000_hw.h
+++ b/drivers/net/ethernet/intel/igb/e1000_hw.h
@@ -528,6 +528,8 @@ struct e1000_dev_spec_82575 {
bool global_device_reset;
bool eee_disable;
bool clear_semaphore_once;
+ struct e1000_sfp_flags eth_flags;
+ bool module_plugged;
};
struct e1000_hw {
diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.c b/drivers/net/ethernet/intel/igb/e1000_phy.c
index 115b0da..1d6a401 100644
--- a/drivers/net/ethernet/intel/igb/e1000_phy.c
+++ b/drivers/net/ethernet/intel/igb/e1000_phy.c
@@ -341,6 +341,130 @@ s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data)
}
/**
+ * igb_read_sfp_data_byte - Reads SFP module data.
+ * @hw: pointer to the HW structure
+ * @offset: byte location offset to be read
+ * @data: read data buffer pointer
+ *
+ * Reads one byte from SFP module data stored
+ * in SFP resided EEPROM memory or SFP diagnostic area.
+ * Function should be called with
+ * E1000_I2CCMD_SFP_DATA_ADDR(<byte offset>) for SFP module database access
+ * E1000_I2CCMD_SFP_DIAG_ADDR(<byte offset>) for SFP diagnostics parameters
+ * access
+ **/
+s32 igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data)
+{
+ u32 i = 0;
+ u32 i2ccmd = 0;
+ u32 data_local = 0;
+
+ if (offset > E1000_I2CCMD_SFP_DIAG_ADDR(255)) {
+ hw_dbg("I2CCMD command address exceeds upper limit\n");
+ return -E1000_ERR_PHY;
+ }
+
+ /* Set up Op-code, EEPROM Address,in the I2CCMD
+ * register. The MAC will take care of interfacing with the
+ * EEPROM to retrieve the desired data.
+ */
+ i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) |
+ E1000_I2CCMD_OPCODE_READ);
+
+ wr32(E1000_I2CCMD, i2ccmd);
+
+ /* Poll the ready bit to see if the I2C read completed */
+ for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) {
+ udelay(50);
+ data_local = rd32(E1000_I2CCMD);
+ if (data_local & E1000_I2CCMD_READY)
+ break;
+ }
+ if (!(data_local & E1000_I2CCMD_READY)) {
+ hw_dbg("I2CCMD Read did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ if (data_local & E1000_I2CCMD_ERROR) {
+ hw_dbg("I2CCMD Error bit set\n");
+ return -E1000_ERR_PHY;
+ }
+ *data = (u8) data_local & 0xFF;
+
+ return 0;
+}
+
+/**
+ * e1000_write_sfp_data_byte - Writes SFP module data.
+ * @hw: pointer to the HW structure
+ * @offset: byte location offset to write to
+ * @data: data to write
+ *
+ * Writes one byte to SFP module data stored
+ * in SFP resided EEPROM memory or SFP diagnostic area.
+ * Function should be called with
+ * E1000_I2CCMD_SFP_DATA_ADDR(<byte offset>) for SFP module database access
+ * E1000_I2CCMD_SFP_DIAG_ADDR(<byte offset>) for SFP diagnostics parameters
+ * access
+ **/
+s32 e1000_write_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 data)
+{
+ u32 i = 0;
+ u32 i2ccmd = 0;
+ u32 data_local = 0;
+
+ if (offset > E1000_I2CCMD_SFP_DIAG_ADDR(255)) {
+ hw_dbg("I2CCMD command address exceeds upper limit\n");
+ return -E1000_ERR_PHY;
+ }
+ /* The programming interface is 16 bits wide
+ * so we need to read the whole word first
+ * then update appropriate byte lane and write
+ * the updated word back.
+ */
+ /* Set up Op-code, EEPROM Address,in the I2CCMD
+ * register. The MAC will take care of interfacing
+ * with an EEPROM to write the data given.
+ */
+ i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) |
+ E1000_I2CCMD_OPCODE_READ);
+ /* Set a command to read single word */
+ wr32(E1000_I2CCMD, i2ccmd);
+ for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) {
+ udelay(50);
+ /* Poll the ready bit to see if lastly
+ * launched I2C operation completed
+ */
+ i2ccmd = rd32(E1000_I2CCMD);
+ if (i2ccmd & E1000_I2CCMD_READY) {
+ /* Check if this is READ or WRITE phase */
+ if ((i2ccmd & E1000_I2CCMD_OPCODE_READ) ==
+ E1000_I2CCMD_OPCODE_READ) {
+ /* Write the selected byte
+ * lane and update whole word
+ */
+ data_local = i2ccmd & 0xFF00;
+ data_local |= data;
+ i2ccmd = ((offset <<
+ E1000_I2CCMD_REG_ADDR_SHIFT) |
+ E1000_I2CCMD_OPCODE_WRITE | data_local);
+ wr32(E1000_I2CCMD, i2ccmd);
+ } else {
+ break;
+ }
+ }
+ }
+ if (!(i2ccmd & E1000_I2CCMD_READY)) {
+ hw_dbg("I2CCMD Write did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ if (i2ccmd & E1000_I2CCMD_ERROR) {
+ hw_dbg("I2CCMD Error bit set\n");
+ return -E1000_ERR_PHY;
+ }
+ return 0;
+}
+
+/**
* igb_read_phy_reg_igp - Read igp PHY register
* @hw: pointer to the HW structure
* @offset: register offset to be read
diff --git a/drivers/net/ethernet/intel/igb/e1000_phy.h b/drivers/net/ethernet/intel/igb/e1000_phy.h
index 784fd1c..6a0873f 100644
--- a/drivers/net/ethernet/intel/igb/e1000_phy.h
+++ b/drivers/net/ethernet/intel/igb/e1000_phy.h
@@ -69,6 +69,8 @@ s32 igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
s32 igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
+s32 igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data);
+s32 e1000_write_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 data);
s32 igb_copper_link_setup_82580(struct e1000_hw *hw);
s32 igb_get_phy_info_82580(struct e1000_hw *hw);
s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
@@ -157,4 +159,22 @@ s32 igb_check_polarity_m88(struct e1000_hw *hw);
#define GS40G_CS_POWER_DOWN 0x0002
#define GS40G_LINE_LB 0x4000
+/* SFP modules ID memory locations */
+#define E1000_SFF_IDENTIFIER_OFFSET 0x00
+#define E1000_SFF_IDENTIFIER_SFF 0x02
+#define E1000_SFF_IDENTIFIER_SFP 0x03
+
+#define E1000_SFF_ETH_FLAGS_OFFSET 0x06
+/* Flags for SFP modules compatible with ETH up to 1Gb */
+struct e1000_sfp_flags {
+ u8 e1000_base_sx:1;
+ u8 e1000_base_lx:1;
+ u8 e1000_base_cx:1;
+ u8 e1000_base_t:1;
+ u8 e100_base_lx:1;
+ u8 e100_base_fx:1;
+ u8 e10_base_bx10:1;
+ u8 e10_base_px:1;
+};
+
#endif
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 7876240..4e54f84 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -142,6 +142,8 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
{
struct igb_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
+ struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+ struct e1000_sfp_flags *eth_flags = &dev_spec->eth_flags;
u32 status;
if (hw->phy.media_type == e1000_media_type_copper) {
@@ -181,30 +183,22 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
ecmd->phy_address = hw->phy.addr;
ecmd->transceiver = XCVR_INTERNAL;
} else {
- ecmd->supported = (SUPPORTED_1000baseT_Full |
- SUPPORTED_100baseT_Full |
- SUPPORTED_FIBRE |
+ ecmd->supported = (SUPPORTED_FIBRE |
SUPPORTED_Autoneg |
SUPPORTED_Pause);
- if (hw->mac.type == e1000_i354)
- ecmd->supported |= SUPPORTED_2500baseX_Full;
-
ecmd->advertising = ADVERTISED_FIBRE;
-
- switch (adapter->link_speed) {
- case SPEED_2500:
- ecmd->advertising = ADVERTISED_2500baseX_Full;
- break;
- case SPEED_1000:
- ecmd->advertising = ADVERTISED_1000baseT_Full;
- break;
- case SPEED_100:
- ecmd->advertising = ADVERTISED_100baseT_Full;
- break;
- default:
- break;
+ if (hw->mac.type == e1000_i354) {
+ ecmd->supported |= SUPPORTED_2500baseX_Full;
+ ecmd->advertising |= ADVERTISED_2500baseX_Full;
+ }
+ if ((eth_flags->e1000_base_lx) || (eth_flags->e1000_base_sx)) {
+ ecmd->supported |= SUPPORTED_1000baseT_Full;
+ ecmd->advertising |= ADVERTISED_1000baseT_Full;
+ }
+ if (eth_flags->e100_base_fx) {
+ ecmd->supported |= SUPPORTED_100baseT_Full;
+ ecmd->advertising |= ADVERTISED_100baseT_Full;
}
-
if (hw->mac.autoneg == 1)
ecmd->advertising |= ADVERTISED_Autoneg;
--
1.7.11.7
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists