| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <544FF35DE7D643DEB9E792FE766A6B69@kosagi.com>
Date: Mon, 5 Aug 2013 16:12:50 +0800
From: Sean Cross <xobs@...agi.com>
To: Sascha Hauer <s.hauer@...gutronix.de>
Cc: Duan Fugang-B38611 <B38611@...escale.com>,
"netdev@...r.kernel.org" <netdev@...r.kernel.org>,
"devicetree@...r.kernel.org"
<devicetree@...r.kernel.org>, David Miller <davem@...emloft.net>,
"stephen@...workplumber.org"
<stephen@...workplumber.org>, Steven Rostedt <rostedt@...dmis.org>
Subject: Re: [PATCH v5] net/phy: micrel: Add OF configuration support
for ksz9021
--
Sean Cross
On Monday, August 5, 2013 at 3:58 PM, Sascha Hauer wrote:
> On Mon, Aug 05, 2013 at 07:04:08AM +0000, Sean Cross wrote:
> > Some boards require custom PHY configuration, for example due to trace
> > length differences. Add the ability to configure these registers in
> > order to get the PHY to function on boards that need it.
> >
> > Because PHYs are auto-detected based on MDIO device IDs, allow PHY
> > configuration to be specified in the parent Ethernet device node if no
> > PHY device node is present.
> >
> > Signed-off-by: Sean Cross <xobs@...agi.com (mailto:xobs@...agi.com)>
> > ---
> > .../devicetree/bindings/net/micrel-ksz9021.txt | 49 ++++++++++
> > drivers/net/phy/micrel.c | 101 +++++++++++++++++++-
> > 2 files changed, 149 insertions(+), 1 deletion(-)
> > create mode 100644 Documentation/devicetree/bindings/net/micrel-ksz9021.txt
> >
> > diff --git a/Documentation/devicetree/bindings/net/micrel-ksz9021.txt b/Documentation/devicetree/bindings/net/micrel-ksz9021.txt
> > new file mode 100644
> > index 0000000..338a7e2
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/micrel-ksz9021.txt
> > @@ -0,0 +1,49 @@
> > +Micrel KSZ9021 Gigabit Ethernet PHY
> > +
> > +Some boards require special tuning values, particularly when it comes to
> > +clock delays. You can specify clock delay values by adding
> > +micrel-specific properties to an Ethernet OF device node.
> > +
> > +All skew control options are specified in picoseconds. The minimum
> > +value is 0, and the maximum value is 3000.
> > +
> > +Optional properties:
> > + - rxc-skew : Skew control of RXC pad
> > + - rxdv-skew : Skew control of RX CTL pad
> > + - txc-skew : Skew control of TXC pad
> > + - txen-skew : Skew control of TX_CTL pad
> > + - rxd0-skew : Skew control of RX data 0 pad
> > + - rxd1-skew : Skew control of RX data 1 pad
> > + - rxd2-skew : Skew control of RX data 2 pad
> > + - rxd3-skew : Skew control of RX data 3 pad
> > + - txd0-skew : Skew control of TX data 0 pad
> > + - txd1-skew : Skew control of TX data 1 pad
> > + - txd2-skew : Skew control of TX data 2 pad
> > + - txd3-skew : Skew control of TX data 3 pad
> > +
> > +Examples:
> > +
> > + /* Attach to an Ethernet device with autodetected PHY */
> > + &enet {
> > + rxc-skew = <3000>; // picoseconds
> > + rxdv-skew = <0>; // picoseconds
> > + txc-skew = <3000>; // picoseconds
> > + txen-skew = <0>; // picoseconds
> > + status = "okay";
> > + };
> > +
> > + /* Attach to an explicitly-specified PHY */
> > + mdio {
> > + phy0: ethernet-phy@0 {
> > + rxc-skew = <3000>; // picoseconds
> > + rxdv-skew = <0>; // picoseconds
> > + txc-skew = <3000>; // picoseconds
> > + txen-skew = <0>; // picoseconds
> > + reg = <0>;
> > + };
> > + };
> > + ethernet@...00 {
> > + status = "okay";
> > + phy = <&phy0>;
> > + phy-mode = "rgmii-id";
> > + };
> > diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
> > index 2510435..3e60ed0 100644
> > --- a/drivers/net/phy/micrel.c
> > +++ b/drivers/net/phy/micrel.c
> > @@ -25,6 +25,7 @@
> > #include <linux/module.h>
> > #include <linux/phy.h>
> > #include <linux/micrel_phy.h>
> > +#include <linux/of.h>
> >
> > /* Operation Mode Strap Override */
> > #define MII_KSZPHY_OMSO 0x16
> > @@ -53,6 +54,18 @@
> > #define KS8737_CTRL_INT_ACTIVE_HIGH (1 << 14)
> > #define KSZ8051_RMII_50MHZ_CLK (1 << 7)
> >
> > +/* Write/read to/from extended registers */
> > +#define MII_KSZPHY_EXTREG 0x0b
> > +#define KSZPHY_EXTREG_WRITE 0x8000
> > +
> > +#define MII_KSZPHY_EXTREG_WRITE 0x0c
> > +#define MII_KSZPHY_EXTREG_READ 0x0d
> > +
> > +/* Extended registers */
> > +#define MII_KSZPHY_CLK_CONTROL_PAD_SKEW 0x104
> > +#define MII_KSZPHY_RX_DATA_PAD_SKEW 0x105
> > +#define MII_KSZPHY_TX_DATA_PAD_SKEW 0x106
> > +
> > static int ksz_config_flags(struct phy_device *phydev)
> > {
> > int regval;
> > @@ -65,6 +78,20 @@ static int ksz_config_flags(struct phy_device *phydev)
> > return 0;
> > }
> >
> > +static int kszphy_extended_write(struct phy_device *phydev,
> > + u32 regnum, u16 val)
> > +{
> > + phy_write(phydev, MII_KSZPHY_EXTREG, KSZPHY_EXTREG_WRITE | regnum);
> > + return phy_write(phydev, MII_KSZPHY_EXTREG_WRITE, val);
> > +}
> > +
> > +static int kszphy_extended_read(struct phy_device *phydev,
> > + u32 regnum)
> > +{
> > + phy_write(phydev, MII_KSZPHY_EXTREG, regnum);
> > + return phy_read(phydev, MII_KSZPHY_EXTREG_READ);
> > +}
> > +
> > static int kszphy_ack_interrupt(struct phy_device *phydev)
> > {
> > /* bit[7..0] int status, which is a read and clear register. */
> > @@ -141,6 +168,78 @@ static int ks8051_config_init(struct phy_device *phydev)
> > return rc < 0 ? rc : 0;
> > }
> >
> > +static int ksz9021_load_values_from_of(struct phy_device *phydev,
> > + struct device_node *of_node, u16 reg,
> > + char *field1, char *field2,
> > + char *field3, char *field4)
> > +{
> > + int val1 = -1;
> > + int val2 = -2;
> > + int val3 = -3;
> > + int val4 = -4;
> > + int newval;
> > + int matches = 0;
> > +
> > + if (!of_property_read_u32(of_node, field1, &val1))
> > + matches++;
> > +
> > + if (!of_property_read_u32(of_node, field2, &val2))
> > + matches++;
> > +
> > + if (!of_property_read_u32(of_node, field3, &val3))
> > + matches++;
> > +
> > + if (!of_property_read_u32(of_node, field4, &val4))
> > + matches++;
> > +
> > + if (!matches)
> > + return 0;
> > +
> > + if (matches < 4)
> > + newval = kszphy_extended_read(phydev, reg);
> > + else
> > + newval = 0;
>
>
>
> Just initialize newval with the reset default of this register. It will
> make this function easier. Also this two step read from dt and evaluate
> afterwards seems unnecessary.
The documentation seems inaccurate here. My datasheet says it defaults to 0x0111, but when I check it for myself it comes out 0x7777. Which value do you think I should take?
> > +
> > + if (val1 != -1)
> > + newval = ((newval & 0xfff0) | ((val1/200)&0xf) << 0);
> > +
> > + if (val2 != -1)
> > + newval = ((newval & 0xff0f) | ((val2/200)&0xf) << 4);
> > +
> > + if (val3 != -1)
> > + newval = ((newval & 0xf0ff) | ((val3/200)&0xf) << 8);
> > +
> > + if (val4 != -1)
> > + newval = ((newval & 0x0fff) | ((val4/200)&0xf) << 12);
> > +
> > + return kszphy_extended_write(phydev, reg, newval);
> > +}
> > +
> > +static int ksz9021_config_init(struct phy_device *phydev)
> > +{
> > + struct device *dev = &phydev->dev;
> > + struct device_node *of_node = dev->of_node;
> > +
> > + if (!of_node && dev->parent->of_node)
> > + of_node = dev->parent->of_node;
> > +
> > + if (of_node) {
> > + ksz9021_load_values_from_of(phydev, of_node,
> > + MII_KSZPHY_CLK_CONTROL_PAD_SKEW,
> > + "txen-skew", "txc-skew",
> > + "rxdv-skew", "rxc-skew");
> > + ksz9021_load_values_from_of(phydev, of_node,
> > + MII_KSZPHY_RX_DATA_PAD_SKEW,
> > + "rxd0-skew", "rxd1-skew",
> > + "rxd2-skew", "rxd3-skew");
> > + ksz9021_load_values_from_of(phydev, of_node,
> > + MII_KSZPHY_TX_DATA_PAD_SKEW,
> > + "txd0-skew", "txd1-skew",
> > + "txd2-skew", "txd3-skew");
>
>
>
> Are you sure this register exists? It's not mentioned in my datasheet,
> only the first two are.
>
I'm very sure the register exists. There's a hole in the documentation where the TX control register should exist. Furthermore, we measured that changing values in this register adjusted the TX skew on the RG-MII wires, and on our board at least, adjusting these values yields increased performance.
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists