| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20131001125844.GB6096@redhat.com>
Date: Tue, 1 Oct 2013 14:58:44 +0200
From: Veaceslav Falico <vfalico@...hat.com>
To: Yuval Mintz <yuvalmin@...adcom.com>
Cc: Jay Vosburgh <fubar@...ibm.com>,
"netdev@...r.kernel.org" <netdev@...r.kernel.org>,
Ariel Elior <ariele@...adcom.com>
Subject: Re: Question regarding failure utilizing bonding mode 5 (balance-tlb)
On Tue, Oct 01, 2013 at 12:56:43PM +0000, Yuval Mintz wrote:
>> On Mon, Sep 30, 2013 at 11:30:40AM +0000, Yuval Mintz wrote:
>> >> > >Again, I think the permanent address is restored only when the bond
>> >> > >releases the slave, which I don't think happens when the slave is
>> unloaded.
>> >> >
>> >> > Given a bond0 with two slaves, eth0 and eth1, in tlb mode, eth0
>> >> > being the active,
>> >> >
>> >> > 1) "ip link set dev eth0 down" which will fail over to eth1
>> >> > (swapping the contents of their dev_addr fields).
>> >> >
>> >> > 2) "ip link set dev eth0 up" eth0 comes back up, reprograms its
>> >> > MAC to the wrong thing (what was in dev_addr).
>> >> >
>> >> > 3) repeat steps 1 and 2 for eth1
>> >> >
>> >> > Is this correct?
>> >> >
>> >>
>> >> Yes, sorry for the earlier confusion.
>> >> I think in the case described `alb_swap_mac_addr()' will be called,
>> >> replacing eth0 and eth1's dev_addr, causing eth0 to have dev_addr
>> >> which defers from the bond device's. Once eth0 reloads, it will use
>> >> the different MAC address for configuring FW/HW.
>> >
>> >Hi,
>> >
>> >Did you by any chance had the time to look at this issue?
>>
>> Hi Yuval,
>>
>> Sorry for getting into the discussion - but I've tried to understand the
>> problem and, possibly, find a fix.
>>
>> I'm not sure that I completely understand it, and I don't have currently
>> hardware on which to test it (though I might have it in the nearest
>> future), so, again, I really am not sure that I won't suggest something
>> completely stupid.
>>
>> Anyway, that being said, I hope that the following patch might fix the
>> problem. I've described the bug and the fix in the changelog, and the code
>> is pretty self-explanitory.
>>
>> And even if the patch fixes the issue - I'm not sure that it's the proper
>> and correct way to do it. But it's definitely worth a try... So, if it's
>> possible, could you please test this patch and see if it fixes it?
>>
>> Warning: I've just compile-tested it.
>>
>> So, FWIW...
>>
>
>Like you, I don't know if yours is the proper way of fixing the issue - but it did
>seem to fix it (the scenario that was described, at least)
>
>Tested-by: Yuval Mintz <yuvalmin@...adcom.com>
Thank you!
I'll then try now to dig it a big futher, and if it happens that this fix is
really the one we need - I'll use your Tested-by, hope that you're ok with
that. Otherwise I'll send a new patch(set) with you in the CC.
Thanks again!
>
>Thanks,
>Yuval
>
>> From 87e6c584b0ae0f0261610d60cf83778feb9c1edb Mon Sep 17
>> 00:00:00 2001
>> From: Veaceslav Falico <vfalico@...hat.com>
>> Date: Mon, 30 Sep 2013 23:14:23 +0200
>> Subject: [PATCH] bonding: ensure that TLB mode's active slave has correct
>> mac filter
>>
>> Currently, in TLB mode we change mac addresses only by memcpy-ing the to
>> net_device->dev_addr, without actually setting them via
>> dev_set_mac_address(). This permits us to receive all the traffic always on
>> one mac address.
>>
>> However, in case the interface flips, some drivers might enforce the
>> mac filtering for its FW/HW based on current ->dev_addr, and thus we won't
>> be able to receive traffic on that interface, in case it will be selected
>> as active in TLB mode.
>>
>> Fix it by setting the mac address forcefully on every new active slave that
>> we select in TLB mode.
>>
>> CC: Jay Vosburgh <fubar@...ibm.com>
>> CC: Andy Gospodarek <andy@...yhouse.net>
>> Signed-off-by: Veaceslav Falico <vfalico@...hat.com>
>> ---
>> drivers/net/bonding/bond_alb.c | 17 +++++++++++++++++
>> 1 file changed, 17 insertions(+)
>>
>> diff --git a/drivers/net/bonding/bond_alb.c b/drivers/net/bonding/bond_alb.c
>> index e960418..576ccea 100644
>> --- a/drivers/net/bonding/bond_alb.c
>> +++ b/drivers/net/bonding/bond_alb.c
>> @@ -1699,6 +1699,23 @@ void bond_alb_handle_active_change(struct
>> bonding *bond, struct slave *new_slave
>>
>> ASSERT_RTNL();
>>
>> + /* in TLB mode, the slave might flip down/up with the old dev_addr,
>> + * and thus filter bond->dev_addr's packets, so force bond's mac
>> + */
>> + if (bond->params.mode == BOND_MODE_TLB) {
>> + struct sockaddr sa;
>> + u8 tmp_addr[ETH_ALEN];
>> +
>> + memcpy(tmp_addr, new_slave->dev->dev_addr, ETH_ALEN);
>> +
>> + memcpy(sa.sa_data, bond->dev->dev_addr, bond->dev-
>> >addr_len);
>> + sa.sa_family = bond->dev->type;
>> + /* we don't care if it can't change its mac, best effort */
>> + dev_set_mac_address(new_slave->dev, &sa);
>> +
>> + memcpy(new_slave->dev->dev_addr, tmp_addr, ETH_ALEN);
>> + }
>> +
>> /* curr_active_slave must be set before calling alb_swap_mac_addr
>> */
>> if (swap_slave) {
>> /* swap mac address */
>> --
>> 1.8.4
>>
>>
>> >
>> >Thanks,
>> >Yuval
>> >
>> >--
>> >To unsubscribe from this list: send the line "unsubscribe netdev" in
>> >the body of a message to majordomo@...r.kernel.org
>> >More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists