Message-ID: <da80c522-5524-4f53-9373-3f2bb6f81ddc@CO9EHSMHS015.ehs.local>
Date:	Tue, 11 Feb 2014 12:45:31 +0100
From:	Michal Simek <michal.simek@...inx.com>
To:	Marc Kleine-Budde <mkl@...gutronix.de>,
	"robh+dt@...nel.org" <robh+dt@...nel.org>,
	Arnd Bergmann <arnd@...db.de>
CC:	Appana Durga Kedareswara Rao <appana.durga.rao@...inx.com>,
	"wg@...ndegger.com" <wg@...ndegger.com>,
	"grant.likely@...aro.org" <grant.likely@...aro.org>,
	"linux-can@...r.kernel.org" <linux-can@...r.kernel.org>,
	"netdev@...r.kernel.org" <netdev@...r.kernel.org>,
	"linux-arm-kernel@...ts.infradead.org" 
	<linux-arm-kernel@...ts.infradead.org>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>
Subject: Re: [PATCH] can: xilinx CAN controller support.

Hi Marc,

On 02/07/2014 10:37 AM, Marc Kleine-Budde wrote:
> On 02/07/2014 09:42 AM, Appana Durga Kedareswara Rao wrote:
>>>> ---
>>>> This patch is rebased on the 3.14 rc1 kernel.
>>>> ---
>>>>  .../devicetree/bindings/net/can/xilinx_can.txt     |   43 +
>>>>  drivers/net/can/Kconfig                            |    8 +
>>>>  drivers/net/can/Makefile                           |    1 +
>>>>  drivers/net/can/xilinx_can.c                       | 1150 ++++++++++++++++++++
>>>>  4 files changed, 1202 insertions(+), 0 deletions(-)  create mode
>>>> 100644 Documentation/devicetree/bindings/net/can/xilinx_can.txt
>>>>  create mode 100644 drivers/net/can/xilinx_can.c
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt
>>>> b/Documentation/devicetree/bindings/net/can/xilinx_can.txt
>>>> new file mode 100644
>>>> index 0000000..34f9643
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/net/can/xilinx_can.txt
>>>> @@ -0,0 +1,43 @@
>>>> +Xilinx Axi CAN/Zynq CANPS controller Device Tree Bindings
>>>> +---------------------------------------------------------
>>>> +
>>>> +Required properties:
>>>> +- compatible               : Should be "xlnx,zynq-can-1.00.a" for Zynq
>>> CAN
>>>> +                     controllers and "xlnx,axi-can-1.00.a" for Axi CAN
>>>> +                     controllers.
>>>> +- reg                      : Physical base address and size of the Axi CAN/Zynq
>>>> +                     CANPS registers map.
>>>> +- interrupts               : Property with a value describing the interrupt
>>>> +                     number.
>>>> +- interrupt-parent : Must be core interrupt controller
>>>> +- clock-names              : List of input clock names - "ref_clk",
>>> "aper_clk"
>>>> +                     (See clock bindings for details. Two clocks are
>>>> +                      required for Zynq CAN. For Axi CAN
>>>> +                      case it is one(ref_clk)).
>>>> +- clocks           : Clock phandles (see clock bindings for details).
>>>> +- xlnx,can-tx-dpth : Can Tx fifo depth (Required for Axi CAN).
>>>> +- xlnx,can-rx-dpth : Can Rx fifo depth (Required for Axi CAN).
>>>> +
>>>> +
>>>> +Example:
>>>> +
>>>> +For Zynq CANPS Dts file:
>>>> +   zynq_can_0: zynq-can@...08000 {
>>>> +                   compatible = "xlnx,zynq-can-1.00.a";
>>>> +                   clocks = <&clkc 19>, <&clkc 36>;
>>>> +                   clock-names = "ref_clk", "aper_clk";
>>>> +                   reg = <0xe0008000 0x1000>;
>>>> +                   interrupts = <0 28 4>;
>>>> +                   interrupt-parent = <&intc>;
>>>
>>> Above xlnx,can-{rx,tx}-dpth is mentioned as required, but it's not in the
>>> Zynq example.
>>
>> One of the Difference b/w the AXI CAN and zynq CAN is in AXI CAN the fifo depth(tx,rx)
>> Is user configurable. But in case of ZYNQ CAN  the fifo depth  is fixed for tx and rx fifo's(64)
>> Xlnx,can-{rx,tx}-dpth is required only for AXI CAN case it is not required for zynq CAN.
>> That's why didn't putted that property in device tree.
> 
> The device tree should be a hardware only description and should not
> hold any user configurable data. Please split your patch into two
> patches. The first one should add the driver with a fixed fifo size
> (e.g. 0x40) for the AXI, too. The second patch should make the fifo
> configurable via device tree.

can-rx/tx-dpth is not user configurable data as you think.
This is FPGA where you can configure this parameter in design tools.
It means these 2 values just describe real hardware and user can't just change it
for different software behaviour.

Also I don't think it is worth to create 2 patches for the same driver
where the first one is useless for axi can device. But if you think
that it is worth to do we can create 2 patches as you suggested.

Also what we can do is to define that this property is required also
for zynq which is 0x40 and change code according too.

> If it's acceptable to describe the fifo usage by device tree, I'd like
> to make it a generic CAN driver option. But we have to look around, e.g.
> what the Ethernet driver use to configure their hardware.

I think the real question is not if this is acceptable or not. It is just
reality that we can setup hardware fifo depth and driver has to reflect this
because without it driver just doesn't work for axi can.

The only remaining question is if we should create generic DT binding
for fifo depth. Arnd, Rob: Any opinion about it?
Definitely will be worth to have one generic binding if this is generic feature.
But if this is just specific feature for us then current properties should
be fine.

In general all these xlnx,XXX properties just reflect all configurable options
which you can setup in design tool which means that provide full hw description
with all variants and they are automatically generated from tools.

Please let me know what you think.

Thanks,
Michal


Download attachment "signature.asc" of type "application/pgp-signature" (265 bytes)

Powered by blists - more mailing lists