| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAGVrzcbdm-owTaz6ENZMCCGDxQsSaHoEVP=5ex9kZj-FprqUxQ@mail.gmail.com>
Date: Tue, 6 May 2014 15:06:01 -0700
From: Florian Fainelli <f.fainelli@...il.com>
To: Brian Lilly <brian@...stalfontz.com>
Cc: Uwe Kleine-König
<u.kleine-koenig@...gutronix.de>,
"David S. Miller" <davem@...emloft.net>,
Fabio Estevam <fabio.estevam@...escale.com>,
Jim Baxter <jim_baxter@...tor.com>,
Frank Li <Frank.Li@...escale.com>,
Fugang Duan <B38611@...escale.com>,
netdev <netdev@...r.kernel.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
kernel <kernel@...gutronix.de>
Subject: Re: i.MX28 based system losing eth0 on boot
2014-05-06 14:40 GMT-07:00 Brian Lilly <brian@...stalfontz.com>:
> The PHY on board is the SMSC LAN8720
>
> With the generic PHY driver selected: http://pastebin.com/A4MH4Ptw
>
> [ 28.828761] fec 800f0000.ethernet eth0: Freescale FEC PHY driver
> [Generic PHY] (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
> [ 28.840626] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 30.827536] libphy: 800f0000.etherne:00 - Link is Up - 100/Full
> [ 30.833739] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 32.986999] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
> [ 37.316421] fec 800f0000.ethernet eth0: Freescale FEC PHY driver
> [Generic PHY] (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
> [ 38.345047] fec 800f0000.ethernet eth0: MDIO read timeout
> [ 39.506210] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 40.374961] fec 800f0000.ethernet eth0: MDIO read timeout
>
> With the SMSC PHY driver selected: http://pastebin.com/DhdDyrMv
>
> [ 28.778974] fec 800f0000.ethernet eth0: Freescale FEC PHY driver
> [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
> [ 28.791742] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 30.773078] libphy: 800f0000.etherne:00 - Link is Up - 100/Full
> [ 30.779286] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 32.934692] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
> [ 37.242162] fec 800f0000.ethernet eth0: Freescale FEC PHY driver
> [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
> [ 38.270611] fec 800f0000.ethernet eth0: MDIO read timeout
> [ 39.415256] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 40.300454] fec 800f0000.ethernet eth0: MDIO read timeout
Thanks for trying this, at least this is consistent no matter which
PHY driver we are using. Just to rule out a potential PHY power-down
issue, could you try to revert the following commit
be9dad1f9f26604fb71c0d53ccb39a8f1d425807 ("net: phy: suspend phydev
when going to HALTED") and see if that works better for you?
Thanks!
>
> On Tue, May 6, 2014 at 12:24 PM, Florian Fainelli <f.fainelli@...il.com> wrote:
>> 2014-05-06 12:12 GMT-07:00 Brian Lilly <brian@...stalfontz.com>:
>>> It is happening during boot up:
>>>
>>> <snip, kernel 3.12 >
>>>
>>> Configuring network interfaces... [ 35.117114] fec 800f0000.ethernet
>>> eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720]
>>
>> Note that the SMSC PHY driver is picked up here, and that specific
>> driver implements a different phy_read_status() callback due to how
>> the PHY operates. The PHY driver also overrides the config_init()
>> callback to perform some PHY-specific initialization. See below for
>> more.
>>
>>> (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
>>> [ 35.129967] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
>>> udhcpc (v1.21.1) started
>>>
>>> Sending discover...
>>>
>>> [ 37.113901] libphy: 800f0000.etherne:00 - Link is Up - 100/Full
>>> [ 37.120134] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>>> Sending discover...
>>>
>>> Sending select for 10.10.10.217...
>>> Lease of 10.10.10.217 obtained, lease time 86400
>>> /etc/udhcpc.d/50default: Adding DNS 10.10.10.13
>>> [ 39.319957] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
>>> done.
>>> Starting rpcbind daemon...done.
>>> net.ipv4.conf.default.rp_filter = 1
>>> net.ipv4.conf.all.rp_filter = 1
>>> Mon Apr 14 22:40:00 UTC 2014
>>> INIT: Entering runlevel: 5
>>> Starting Xserver
>>> Starting system message bus: dbus.
>>> Starting Connection Manager
>>> Starting wpa_supplicant
>>> Successfully initialized wpa_supplicant
>>> Starting Dropbear SSH server
>>> [ 44.754915] fec 800f0000.ethernet eth0: Freescale FEC PHY driver
>>> [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
>>
>> The correct PHY driver is selected here...
>>
>>> [ 45.781364] fec 800f0000.ethernet eth0: MDIO read timeout
>>> [ 46.826170] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
>>> [ 47.811385] fec 800f0000.ethernet eth0: MDIO read timeout
>>
>> But we are still seeing MDIO read timeouts, which is not great.
>>
>>>
>>> With a different kernel (3.14):
>>>
>>> [ 28.989897] fec 800f0000.ethernet eth0: Freescale FEC PHY driver
>>> [Generic PHY] (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
>>> [ 30.991210] libphy: 800f0000.etherne:00 - Link is Up - 100/Full
>>> [ 37.369372] fec 800f0000.ethernet eth0: Freescale FEC PHY driver
>>> [Generic PHY] (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
>>
>> Here, the Generic PHY driver has been selected, which will use the
>> MII_BMSR register contents to determine the Link status and
>> parameters. You might want to make sure that your board selects the
>> appropriate PHY driver, such that we are not chasing two issues here.
>>
>>> [ 38.398346] fec 800f0000.ethernet eth0: MDIO read timeout
>>> [ 39.438412] fec 800f0000.ethernet eth0: MDIO read timeout
>>> [ 39.468419] fec 800f0000.ethernet eth0: MDIO write timeout
>>> [ 40.498848] fec 800f0000.ethernet eth0: MDIO read timeout
>>
>> It would also be helpful to print the register that were accessed,
>> such that you could correlate this with the exact steps in the PHY
>> library state machine. Please also retry the experiment with the SMSC
>> PHY driver enabled, as it does some PHY specific initialization that
>> seems to be relevant. Then we are hopefully left with only the MDIO
>> timeout issue and not the PHY mis-configuration + MDIO timeout.
>>
>>>
>>> Afterward I have to ifdown eth0, ifup eth0 and then it functions
>>> normally, without reverting the commit.
>>>
>>> root@...100xx:~# ifdown eth0
>>> [ 1154.679658] fec 800f0000.ethernet eth0: Freescale FEC PHY driver
>>> [Generic PHY] (mii_bus:phy_addr=800f0000.etherne:00, irq=-1)
>>> root@...100xx:~# ifup eth0
>>> udhcpc (v1.21.1) started
>>> Sending discover...
>>> [ 1156.679547] libphy: 800f0000.etherne:00 - Link is Up - 100/Full
>>> Sending discover...
>>> Sending select for 10.10.10.217...
>>> Lease of 10.10.10.217 obtained, lease time 86400
>>> ip: RTNETLINK answers: File exists
>>>
>>> --
>>> Brian
>>>
>>>
>>> On Tue, May 6, 2014 at 11:11 AM, Uwe Kleine-König
>>> <u.kleine-koenig@...gutronix.de> wrote:
>>>> Hello Brian,
>>>>
>>>> On Tue, May 06, 2014 at 09:44:34AM -0700, Brian Lilly wrote:
>>>>> With commit a264b981f2c76e281ef27e7232774bf6c54ec865 we're having eth0
>>>>> come up, then brought right back down with an MDIO rx timeout moments
>>>>> after. Adding back in the removed code keeps the interface alive and
>>>>> it's working afterward without trouble. I've tested the re-inserted
>>>>> code in 3.12, 3.14 without issue on our boards.
>>>> So you can reliably trigger that problem? You're just doing
>>>>
>>>> ifconfig eth0 1.2.3.4 up
>>>>
>>>> (or equivalent) and the interface goes down without further
>>>> interference with the above mentioned commit? The exact error you're
>>>> seeing is
>>>>
>>>> MDIO read timeout
>>>>
>>>> (with some prefix saying something about fec and eth0 I think)?
>>>>
>>>> This error is also present with a264b981f2 reverted, just doesn't affect
>>>> eth0 being functional? Does the timeout always happen, or only on
>>>> specific addresses?
>>>>
>>>> This is not a proper fix, but does it help to increment FEC_MII_TIMEOUT?
>>>>
>>>>> Is there something else that can be done to prevent the MDIO timeouts?
>>>>> We are using basically the same schematic for networking as the
>>>>> imx28evk.
>>>> Hard to say, but assuming it works just fine on the imx28evk for you,
>>>> too, there seems to be some hardware difference that makes your machine
>>>> fail. (That doesn't mean it's not fixable in software.)
>>>>
>>>> I don't know if a mdio read error is intended to make the device go
>>>> down, maybe one the the netdev guys can answer that.
>>>> Assuming that it's not intended, instrument the code, find out how that
>>>> timeout makes your device go down and find the wrong branch. I'd start
>>>> with adding stackdumps when the mdio timeout happens and when
>>>> fec_enet_start_xmit is called with fep->link == 0.
>>>>
>>>> Best regards
>>>> Uwe
>>>>
>>>> --
>>>> Pengutronix e.K. | Uwe Kleine-König |
>>>> Industrial Linux Solutions | http://www.pengutronix.de/ |
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe netdev" in
>>> the body of a message to majordomo@...r.kernel.org
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>>
>>
>> --
>> Florian
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists