| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1408283271-16176-3-git-send-email-Yuval.Mintz@qlogic.com>
Date: Sun, 17 Aug 2014 16:47:44 +0300
From: Yuval Mintz <Yuval.Mintz@...gic.com>
To: <davem@...emloft.net>, <netdev@...r.kernel.org>
CC: <Ariel.Elior@...gic.com>,
Michal Kalderon <Michal.Kalderon@...gic.com>,
Yuval Mintz <Yuval.Mintz@...gic.com>
Subject: [PATCH net-next 2/9] bnx2x: Add timestamping and PTP hardware clock support
From: Michal Kalderon <Michal.Kalderon@...gic.com>
This adds a PHC to the bnx2x driver. Driver supports timestamping send/receive
PTP packets, as well as adjusting the on-chip clock.
The driver has been tested with linuxptp project.
Signed-off-by: Michal Kalderon <Michal.Kalderon@...gic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@...gic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@...gic.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h | 27 +
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 25 +-
.../net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c | 42 ++-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h | 47 ++-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 599 +++++++++++++++++++-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h | 178 ++++++-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c | 50 ++
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h | 29 +-
8 files changed, 984 insertions(+), 13 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
index d777fae..a0b06a0 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -20,6 +20,10 @@
#include <linux/types.h>
#include <linux/pci_regs.h>
+#include <linux/ptp_clock_kernel.h>
+#include <linux/net_tstamp.h>
+#include <linux/clocksource.h>
+
/* compilation time flags */
/* define this to make the driver freeze on error to allow getting debug info
@@ -70,6 +74,7 @@ enum bnx2x_int_mode {
#define BNX2X_MSG_SP 0x0100000 /* was: NETIF_MSG_INTR */
#define BNX2X_MSG_FP 0x0200000 /* was: NETIF_MSG_INTR */
#define BNX2X_MSG_IOV 0x0800000
+#define BNX2X_MSG_PTP 0x1000000
#define BNX2X_MSG_IDLE 0x2000000 /* used for idle check*/
#define BNX2X_MSG_ETHTOOL 0x4000000
#define BNX2X_MSG_DCB 0x8000000
@@ -1591,6 +1596,8 @@ struct bnx2x {
#define BC_SUPPORTS_RMMOD_CMD (1 << 24)
#define HAS_PHYS_PORT_ID (1 << 25)
#define AER_ENABLED (1 << 26)
+#define PTP_SUPPORTED (1 << 27)
+#define TX_TIMESTAMPING_EN (1 << 28)
#define BP_NOMCP(bp) ((bp)->flags & NO_MCP_FLAG)
@@ -1933,6 +1940,19 @@ struct bnx2x {
u8 phys_port_id[ETH_ALEN];
+ /* PTP related context */
+ struct ptp_clock *ptp_clock;
+ struct ptp_clock_info ptp_clock_info;
+ struct work_struct ptp_task;
+ struct cyclecounter cyclecounter;
+ struct timecounter timecounter;
+ bool timecounter_init_done;
+ struct sk_buff *ptp_tx_skb;
+ unsigned long ptp_tx_start;
+ bool hwtstamp_ioctl_called;
+ u16 tx_type;
+ u16 rx_filter;
+
struct bnx2x_link_report_data vf_link_vars;
};
@@ -2559,4 +2579,11 @@ void bnx2x_update_mng_version(struct bnx2x *bp);
#define E1H_MAX_MF_SB_COUNT (HC_SB_MAX_SB_E1X/(E1HVN_MAX * PORT_MAX))
+void bnx2x_init_ptp(struct bnx2x *bp);
+int bnx2x_configure_ptp_filters(struct bnx2x *bp);
+void bnx2x_set_rx_ts(struct bnx2x *bp, struct sk_buff *skb);
+
+#define BNX2X_MAX_PHC_DRIFT 31000000
+#define BNX2X_PTP_TX_TIMEOUT
+
#endif /* bnx2x.h */
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
index e35326c..a1dd2e4 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
@@ -1067,6 +1067,11 @@ reuse_rx:
skb_record_rx_queue(skb, fp->rx_queue);
+ /* Check if this packet was timestamped */
+ if (unlikely(le16_to_cpu(cqe->fast_path_cqe.type_error_flags) &
+ (1 << ETH_FAST_PATH_RX_CQE_PTP_PKT_SHIFT)))
+ bnx2x_set_rx_ts(bp, skb);
+
if (le16_to_cpu(cqe_fp->pars_flags.flags) &
PARSING_FLAGS_VLAN)
__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q),
@@ -2808,7 +2813,11 @@ int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
/* Initialize Rx filter. */
bnx2x_set_rx_mode_inner(bp);
- /* Start the Tx */
+ if (bp->flags & PTP_SUPPORTED) {
+ bnx2x_init_ptp(bp);
+ bnx2x_configure_ptp_filters(bp);
+ }
+ /* Start Tx */
switch (load_mode) {
case LOAD_NORMAL:
/* Tx queue should be only re-enabled */
@@ -3833,6 +3842,20 @@ netdev_tx_t bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev)
tx_start_bd->bd_flags.as_bitfield = ETH_TX_BD_FLAGS_START_BD;
+ if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)) {
+ if (!(bp->flags & TX_TIMESTAMPING_EN)) {
+ BNX2X_ERR("Tx timestamping was not enabled, this packet will not be timestamped\n");
+ } else if (bp->ptp_tx_skb) {
+ BNX2X_ERR("The device supports only a single outstanding packet to timestamp, this packet will not be timestamped\n");
+ } else {
+ skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
+ /* schedule check for Tx timestamp */
+ bp->ptp_tx_skb = skb_get(skb);
+ bp->ptp_tx_start = jiffies;
+ schedule_work(&bp->ptp_task);
+ }
+ }
+
/* header nbd: indirectly zero other flags! */
tx_start_bd->general_data = 1 << ETH_TX_START_BD_HDR_NBDS_SHIFT;
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
index 92fee84..0b173ed 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
@@ -3481,6 +3481,46 @@ static int bnx2x_set_channels(struct net_device *dev,
return bnx2x_nic_load(bp, LOAD_NORMAL);
}
+static int bnx2x_get_ts_info(struct net_device *dev,
+ struct ethtool_ts_info *info)
+{
+ struct bnx2x *bp = netdev_priv(dev);
+
+ if (bp->flags & PTP_SUPPORTED) {
+ info->so_timestamping = SOF_TIMESTAMPING_TX_SOFTWARE |
+ SOF_TIMESTAMPING_RX_SOFTWARE |
+ SOF_TIMESTAMPING_SOFTWARE |
+ SOF_TIMESTAMPING_TX_HARDWARE |
+ SOF_TIMESTAMPING_RX_HARDWARE |
+ SOF_TIMESTAMPING_RAW_HARDWARE;
+
+ if (bp->ptp_clock)
+ info->phc_index = ptp_clock_index(bp->ptp_clock);
+ else
+ info->phc_index = -1;
+
+ info->rx_filters = (1 << HWTSTAMP_FILTER_NONE) |
+ (1 << HWTSTAMP_FILTER_PTP_V1_L4_EVENT) |
+ (1 << HWTSTAMP_FILTER_PTP_V1_L4_SYNC) |
+ (1 << HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_L4_EVENT) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_L4_SYNC) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_L2_EVENT) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_L2_SYNC) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_EVENT) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_SYNC) |
+ (1 << HWTSTAMP_FILTER_PTP_V2_DELAY_REQ);
+
+ info->tx_types = (1 << HWTSTAMP_TX_OFF)|(1 << HWTSTAMP_TX_ON);
+
+ return 0;
+ }
+
+ return ethtool_op_get_ts_info(dev, info);
+}
+
static const struct ethtool_ops bnx2x_ethtool_ops = {
.get_settings = bnx2x_get_settings,
.set_settings = bnx2x_set_settings,
@@ -3522,7 +3562,7 @@ static const struct ethtool_ops bnx2x_ethtool_ops = {
.get_module_eeprom = bnx2x_get_module_eeprom,
.get_eee = bnx2x_get_eee,
.set_eee = bnx2x_set_eee,
- .get_ts_info = ethtool_op_get_ts_info,
+ .get_ts_info = bnx2x_get_ts_info,
};
static const struct ethtool_ops bnx2x_vf_ethtool_ops = {
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
index 3b6cbd2..7ea0453 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
@@ -3547,7 +3547,9 @@ struct client_init_rx_data {
__le16 rx_cos_mask;
__le16 silent_vlan_value;
__le16 silent_vlan_mask;
- __le32 reserved6[2];
+ u8 handle_ptp_pkts_flg;
+ u8 reserved6[3];
+ __le32 reserved7;
};
/*
@@ -3616,7 +3618,9 @@ struct client_update_ramrod_data {
u8 refuse_outband_vlan_change_flg;
u8 tx_switching_flg;
u8 tx_switching_change_flg;
- __le32 reserved1;
+ u8 handle_ptp_pkts_flg;
+ u8 handle_ptp_pkts_change_flg;
+ __le16 reserved1;
__le32 echo;
};
@@ -3850,8 +3854,10 @@ struct eth_fast_path_rx_cqe {
#define ETH_FAST_PATH_RX_CQE_IP_BAD_XSUM_FLG_SHIFT 4
#define ETH_FAST_PATH_RX_CQE_L4_BAD_XSUM_FLG (0x1<<5)
#define ETH_FAST_PATH_RX_CQE_L4_BAD_XSUM_FLG_SHIFT 5
-#define ETH_FAST_PATH_RX_CQE_RESERVED0 (0x3<<6)
-#define ETH_FAST_PATH_RX_CQE_RESERVED0_SHIFT 6
+#define ETH_FAST_PATH_RX_CQE_PTP_PKT (0x1<<6)
+#define ETH_FAST_PATH_RX_CQE_PTP_PKT_SHIFT 6
+#define ETH_FAST_PATH_RX_CQE_RESERVED0 (0x1<<7)
+#define ETH_FAST_PATH_RX_CQE_RESERVED0_SHIFT 7
u8 status_flags;
#define ETH_FAST_PATH_RX_CQE_RSS_HASH_TYPE (0x7<<0)
#define ETH_FAST_PATH_RX_CQE_RSS_HASH_TYPE_SHIFT 0
@@ -5658,6 +5664,16 @@ struct protocol_common_spe {
union protocol_common_specific_data data;
};
+/* The data for the Set Timesync Ramrod */
+struct set_timesync_ramrod_data {
+ u8 drift_adjust_cmd;
+ u8 offset_cmd;
+ u8 add_sub_drift_adjust_value;
+ u8 drift_adjust_value;
+ u32 drift_adjust_period;
+ struct regpair offset_delta;
+};
+
/*
* The send queue element
*/
@@ -5780,6 +5796,29 @@ struct tstorm_vf_zone_data {
struct regpair reserved;
};
+/* Add or Subtract Value for Set Timesync Ramrod */
+enum ts_add_sub_value {
+ TS_SUB_VALUE,
+ TS_ADD_VALUE,
+ MAX_TS_ADD_SUB_VALUE
+};
+
+/* Drift-Adjust Commands for Set Timesync Ramrod */
+enum ts_drift_adjust_cmd {
+ TS_DRIFT_ADJUST_KEEP,
+ TS_DRIFT_ADJUST_SET,
+ TS_DRIFT_ADJUST_RESET,
+ MAX_TS_DRIFT_ADJUST_CMD
+};
+
+/* Offset Commands for Set Timesync Ramrod */
+enum ts_offset_cmd {
+ TS_OFFSET_KEEP,
+ TS_OFFSET_INC,
+ TS_OFFSET_DEC,
+ MAX_TS_OFFSET_CMD
+};
+
/* Tunnel Mode */
enum tunnel_mode {
TUNN_MODE_NONE,
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index a827c9f..423e4b8 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -63,7 +63,6 @@
#include "bnx2x_vfpf.h"
#include "bnx2x_dcb.h"
#include "bnx2x_sp.h"
-
#include <linux/firmware.h>
#include "bnx2x_fw_file_hdr.h"
/* FW files */
@@ -290,6 +289,8 @@ static int bnx2x_set_storm_rx_mode(struct bnx2x *bp);
* General service functions
****************************************************************************/
+static int bnx2x_hwtstamp_ioctl(struct bnx2x *bp, struct ifreq *ifr);
+
static void __storm_memset_dma_mapping(struct bnx2x *bp,
u32 addr, dma_addr_t mapping)
{
@@ -523,6 +524,7 @@ int bnx2x_issue_dmae_with_comp(struct bnx2x *bp, struct dmae_command *dmae,
* as long as this code is called both from syscall context and
* from ndo_set_rx_mode() flow that may be called from BH.
*/
+
spin_lock_bh(&bp->dmae_lock);
/* reset completion */
@@ -551,7 +553,9 @@ int bnx2x_issue_dmae_with_comp(struct bnx2x *bp, struct dmae_command *dmae,
}
unlock:
+
spin_unlock_bh(&bp->dmae_lock);
+
return rc;
}
@@ -5452,6 +5456,14 @@ static void bnx2x_eq_int(struct bnx2x *bp)
break;
goto next_spqe;
+
+ case EVENT_RING_OPCODE_SET_TIMESYNC:
+ DP(BNX2X_MSG_SP | BNX2X_MSG_PTP,
+ "got set_timesync ramrod completion\n");
+ if (f_obj->complete_cmd(bp, f_obj,
+ BNX2X_F_CMD_SET_TIMESYNC))
+ break;
+ goto next_spqe;
}
switch (opcode | bp->state) {
@@ -9033,6 +9045,48 @@ static int bnx2x_func_wait_started(struct bnx2x *bp)
return 0;
}
+static void bnx2x_disable_ptp(struct bnx2x *bp)
+{
+ int port = BP_PORT(bp);
+
+ /* Disable sending PTP packets to host */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_TO_HOST :
+ NIG_REG_P0_LLH_PTP_TO_HOST, 0x0);
+
+ /* Reset PTP event detection rules */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+ NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x7FF);
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+ NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3FFF);
+ REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_PARAM_MASK :
+ NIG_REG_P0_TLLH_PTP_PARAM_MASK, 0x7FF);
+ REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_RULE_MASK :
+ NIG_REG_P0_TLLH_PTP_RULE_MASK, 0x3FFF);
+
+ /* Disable the PTP feature */
+ REG_WR(bp, port ? NIG_REG_P1_PTP_EN :
+ NIG_REG_P0_PTP_EN, 0x0);
+}
+
+/* Called during unload, to stop PTP-related stuff */
+void bnx2x_stop_ptp(struct bnx2x *bp)
+{
+ /* Cancel PTP work queue. Should be done after the Tx queues are
+ * drained to prevent additional scheduling.
+ */
+ cancel_work_sync(&bp->ptp_task);
+
+ if (bp->ptp_tx_skb) {
+ dev_kfree_skb_any(bp->ptp_tx_skb);
+ bp->ptp_tx_skb = NULL;
+ }
+
+ /* Disable PTP in HW */
+ bnx2x_disable_ptp(bp);
+
+ DP(BNX2X_MSG_PTP, "PTP stop ended successfully\n");
+}
+
void bnx2x_chip_cleanup(struct bnx2x *bp, int unload_mode, bool keep_link)
{
int port = BP_PORT(bp);
@@ -9151,6 +9205,13 @@ unload_error:
#endif
}
+ /* stop_ptp should be after the Tx queues are drained to prevent
+ * scheduling to the cancelled PTP work queue. It should also be after
+ * function stop ramrod is sent, since as part of this ramrod FW access
+ * PTP registers.
+ */
+ bnx2x_stop_ptp(bp);
+
/* Disable HW interrupts, NAPI */
bnx2x_netif_stop(bp, 1);
/* Delete all NAPI objects */
@@ -12023,6 +12084,9 @@ static int bnx2x_init_bp(struct bnx2x *bp)
bp->dump_preset_idx = 1;
+ if (CHIP_IS_E3B0(bp))
+ bp->flags |= PTP_SUPPORTED;
+
return rc;
}
@@ -12355,13 +12419,17 @@ static int bnx2x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
struct bnx2x *bp = netdev_priv(dev);
struct mii_ioctl_data *mdio = if_mii(ifr);
- DP(NETIF_MSG_LINK, "ioctl: phy id 0x%x, reg 0x%x, val_in 0x%x\n",
- mdio->phy_id, mdio->reg_num, mdio->val_in);
-
if (!netif_running(dev))
return -EAGAIN;
- return mdio_mii_ioctl(&bp->mdio, mdio, cmd);
+ switch (cmd) {
+ case SIOCSHWTSTAMP:
+ return bnx2x_hwtstamp_ioctl(bp, ifr);
+ default:
+ DP(NETIF_MSG_LINK, "ioctl: phy id 0x%x, reg 0x%x, val_in 0x%x\n",
+ mdio->phy_id, mdio->reg_num, mdio->val_in);
+ return mdio_mii_ioctl(&bp->mdio, mdio, cmd);
+ }
}
#ifdef CONFIG_NET_POLL_CONTROLLER
@@ -13005,6 +13073,191 @@ static int set_is_vf(int chip_id)
}
}
+/* nig_tsgen registers relative address */
+#define tsgen_ctrl 0x0
+#define tsgen_freecount 0x10
+#define tsgen_synctime_t0 0x20
+#define tsgen_offset_t0 0x28
+#define tsgen_drift_t0 0x30
+#define tsgen_synctime_t1 0x58
+#define tsgen_offset_t1 0x60
+#define tsgen_drift_t1 0x68
+
+/* FW workaround for setting drift */
+static int bnx2x_send_update_drift_ramrod(struct bnx2x *bp, int drift_dir,
+ int best_val, int best_period)
+{
+ struct bnx2x_func_state_params func_params = {NULL};
+ struct bnx2x_func_set_timesync_params *set_timesync_params =
+ &func_params.params.set_timesync;
+
+ /* Prepare parameters for function state transitions */
+ __set_bit(RAMROD_COMP_WAIT, &func_params.ramrod_flags);
+ __set_bit(RAMROD_RETRY, &func_params.ramrod_flags);
+
+ func_params.f_obj = &bp->func_obj;
+ func_params.cmd = BNX2X_F_CMD_SET_TIMESYNC;
+
+ /* Function parameters */
+ set_timesync_params->drift_adjust_cmd = TS_DRIFT_ADJUST_SET;
+ set_timesync_params->offset_cmd = TS_OFFSET_KEEP;
+ set_timesync_params->add_sub_drift_adjust_value =
+ drift_dir ? TS_ADD_VALUE : TS_SUB_VALUE;
+ set_timesync_params->drift_adjust_value = best_val;
+ set_timesync_params->drift_adjust_period = best_period;
+
+ return bnx2x_func_state_change(bp, &func_params);
+}
+
+static int bnx2x_ptp_adjfreq(struct ptp_clock_info *ptp, s32 ppb)
+{
+ struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+ int rc;
+ int drift_dir = 1;
+ int val, period, period1, period2, dif, dif1, dif2;
+ int best_dif = BNX2X_MAX_PHC_DRIFT, best_period = 0, best_val = 0;
+
+ DP(BNX2X_MSG_PTP, "PTP adjfreq called, ppb = %d\n", ppb);
+
+ if (!netif_running(bp->dev)) {
+ DP(BNX2X_MSG_PTP,
+ "PTP adjfreq called while the interface is down\n");
+ return -EFAULT;
+ }
+
+ if (ppb < 0) {
+ ppb = -ppb;
+ drift_dir = 0;
+ }
+
+ if (ppb == 0) {
+ best_val = 1;
+ best_period = 0x1FFFFFF;
+ } else if (ppb >= BNX2X_MAX_PHC_DRIFT) {
+ best_val = 31;
+ best_period = 1;
+ } else {
+ /* Changed not to allow val = 8, 16, 24 as these values
+ * are not supported in workaround.
+ */
+ for (val = 0; val <= 31; val++) {
+ if ((val & 0x7) == 0)
+ continue;
+ period1 = val * 1000000 / ppb;
+ period2 = period1 + 1;
+ if (period1 != 0)
+ dif1 = ppb - (val * 1000000 / period1);
+ else
+ dif1 = BNX2X_MAX_PHC_DRIFT;
+ if (dif1 < 0)
+ dif1 = -dif1;
+ dif2 = ppb - (val * 1000000 / period2);
+ if (dif2 < 0)
+ dif2 = -dif2;
+ dif = (dif1 < dif2) ? dif1 : dif2;
+ period = (dif1 < dif2) ? period1 : period2;
+ if (dif < best_dif) {
+ best_dif = dif;
+ best_val = val;
+ best_period = period;
+ }
+ }
+ }
+
+ rc = bnx2x_send_update_drift_ramrod(bp, drift_dir, best_val,
+ best_period);
+ if (rc) {
+ BNX2X_ERR("Failed to set drift\n");
+ return -EFAULT;
+ }
+
+ DP(BNX2X_MSG_PTP, "Configrued val = %d, period = %d\n", best_val,
+ best_period);
+
+ return 0;
+}
+
+static int bnx2x_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
+{
+ struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+ u64 now;
+
+ DP(BNX2X_MSG_PTP, "PTP adjtime called, delta = %llx\n", delta);
+
+ now = timecounter_read(&bp->timecounter);
+ now += delta;
+ /* Re-init the timecounter */
+ timecounter_init(&bp->timecounter, &bp->cyclecounter, now);
+
+ return 0;
+}
+
+static int bnx2x_ptp_gettime(struct ptp_clock_info *ptp, struct timespec *ts)
+{
+ struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+ u64 ns;
+ u32 remainder;
+
+ ns = timecounter_read(&bp->timecounter);
+
+ DP(BNX2X_MSG_PTP, "PTP gettime called, ns = %llu\n", ns);
+
+ ts->tv_sec = div_u64_rem(ns, 1000000000ULL, &remainder);
+ ts->tv_nsec = remainder;
+
+ return 0;
+}
+
+static int bnx2x_ptp_settime(struct ptp_clock_info *ptp,
+ const struct timespec *ts)
+{
+ struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+ u64 ns;
+
+ ns = ts->tv_sec * 1000000000ULL;
+ ns += ts->tv_nsec;
+
+ DP(BNX2X_MSG_PTP, "PTP settime called, ns = %llu\n", ns);
+
+ /* Re-init the timecounter */
+ timecounter_init(&bp->timecounter, &bp->cyclecounter, ns);
+
+ return 0;
+}
+
+/* Enable (or disable) ancillary features of the phc subsystem */
+static int bnx2x_ptp_enable(struct ptp_clock_info *ptp,
+ struct ptp_clock_request *rq, int on)
+{
+ struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+
+ BNX2X_ERR("PHC ancillary features are not supported\n");
+ return -ENOTSUPP;
+}
+
+void bnx2x_register_phc(struct bnx2x *bp)
+{
+ /* Fill the ptp_clock_info struct and register PTP clock*/
+ bp->ptp_clock_info.owner = THIS_MODULE;
+ snprintf(bp->ptp_clock_info.name, 16, "%s", bp->dev->name);
+ bp->ptp_clock_info.max_adj = BNX2X_MAX_PHC_DRIFT; /* In PPB */
+ bp->ptp_clock_info.n_alarm = 0;
+ bp->ptp_clock_info.n_ext_ts = 0;
+ bp->ptp_clock_info.n_per_out = 0;
+ bp->ptp_clock_info.pps = 0;
+ bp->ptp_clock_info.adjfreq = bnx2x_ptp_adjfreq;
+ bp->ptp_clock_info.adjtime = bnx2x_ptp_adjtime;
+ bp->ptp_clock_info.gettime = bnx2x_ptp_gettime;
+ bp->ptp_clock_info.settime = bnx2x_ptp_settime;
+ bp->ptp_clock_info.enable = bnx2x_ptp_enable;
+
+ bp->ptp_clock = ptp_clock_register(&bp->ptp_clock_info, &bp->pdev->dev);
+ if (IS_ERR(bp->ptp_clock)) {
+ bp->ptp_clock = NULL;
+ BNX2X_ERR("PTP clock registeration failed\n");
+ }
+}
+
static int bnx2x_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
@@ -13176,6 +13429,8 @@ static int bnx2x_init_one(struct pci_dev *pdev,
"Unknown",
dev->base_addr, bp->pdev->irq, dev->dev_addr);
+ bnx2x_register_phc(bp);
+
return 0;
init_one_exit:
@@ -13202,6 +13457,11 @@ static void __bnx2x_remove(struct pci_dev *pdev,
struct bnx2x *bp,
bool remove_netdev)
{
+ if (bp->ptp_clock) {
+ ptp_clock_unregister(bp->ptp_clock);
+ bp->ptp_clock = NULL;
+ }
+
/* Delete storage MAC address */
if (!NO_FCOE(bp)) {
rtnl_lock();
@@ -14177,3 +14437,332 @@ int bnx2x_pretend_func(struct bnx2x *bp, u16 pretend_func_val)
REG_RD(bp, pretend_reg);
return 0;
}
+
+static void bnx2x_ptp_task(struct work_struct *work)
+{
+ struct bnx2x *bp = container_of(work, struct bnx2x, ptp_task);
+ int port = BP_PORT(bp);
+ u32 val_seq;
+ u64 timestamp, ns;
+ struct skb_shared_hwtstamps shhwtstamps;
+
+ /* Read Tx timestamp registers */
+ val_seq = REG_RD(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_SEQID :
+ NIG_REG_P0_TLLH_PTP_BUF_SEQID);
+ if (val_seq & 0x10000) {
+ /* There is a valid timestamp value */
+ timestamp = REG_RD(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_TS_MSB :
+ NIG_REG_P0_TLLH_PTP_BUF_TS_MSB);
+ timestamp <<= 32;
+ timestamp |= REG_RD(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_TS_LSB :
+ NIG_REG_P0_TLLH_PTP_BUF_TS_LSB);
+ /* Reset timestamp register to allow new timestamp */
+ REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_SEQID :
+ NIG_REG_P0_TLLH_PTP_BUF_SEQID, 0x10000);
+ ns = timecounter_cyc2time(&bp->timecounter, timestamp);
+
+ memset(&shhwtstamps, 0, sizeof(shhwtstamps));
+ shhwtstamps.hwtstamp = ns_to_ktime(ns);
+ skb_tstamp_tx(bp->ptp_tx_skb, &shhwtstamps);
+ dev_kfree_skb_any(bp->ptp_tx_skb);
+ bp->ptp_tx_skb = NULL;
+
+ DP(BNX2X_MSG_PTP, "Tx timestamp, timestamp cycles = %llu, ns = %llu\n",
+ timestamp, ns);
+ } else {
+ DP(BNX2X_MSG_PTP, "There is no valid Tx timestamp yet\n");
+ /* Reschedule to keep checking for a valid timestamp value */
+ schedule_work(&bp->ptp_task);
+ }
+}
+
+void bnx2x_set_rx_ts(struct bnx2x *bp, struct sk_buff *skb)
+{
+ int port = BP_PORT(bp);
+ u64 timestamp, ns;
+
+ timestamp = REG_RD(bp, port ? NIG_REG_P1_LLH_PTP_HOST_BUF_TS_MSB :
+ NIG_REG_P0_LLH_PTP_HOST_BUF_TS_MSB);
+ timestamp <<= 32;
+ timestamp |= REG_RD(bp, port ? NIG_REG_P1_LLH_PTP_HOST_BUF_TS_LSB :
+ NIG_REG_P0_LLH_PTP_HOST_BUF_TS_LSB);
+
+ /* Reset timestamp register to allow new timestamp */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID :
+ NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID, 0x10000);
+
+ ns = timecounter_cyc2time(&bp->timecounter, timestamp);
+
+ skb_hwtstamps(skb)->hwtstamp = ns_to_ktime(ns);
+
+ DP(BNX2X_MSG_PTP, "Rx timestamp, timestamp cycles = %llu, ns = %llu\n",
+ timestamp, ns);
+}
+
+/* Read the PHC */
+static cycle_t bnx2x_cyclecounter_read(const struct cyclecounter *cc)
+{
+ struct bnx2x *bp = container_of(cc, struct bnx2x, cyclecounter);
+ int port = BP_PORT(bp);
+ u32 wb_data[2];
+ u64 phc_cycles;
+
+ REG_RD_DMAE(bp, port ? NIG_REG_TIMESYNC_GEN_REG + tsgen_synctime_t1 :
+ NIG_REG_TIMESYNC_GEN_REG + tsgen_synctime_t0, wb_data, 2);
+ phc_cycles = wb_data[1];
+ phc_cycles = (phc_cycles << 32) + wb_data[0];
+
+ DP(BNX2X_MSG_PTP, "PHC read cycles = %llu\n", phc_cycles);
+
+ return phc_cycles;
+}
+
+static void bnx2x_init_cyclecounter(struct bnx2x *bp)
+{
+ memset(&bp->cyclecounter, 0, sizeof(bp->cyclecounter));
+ bp->cyclecounter.read = bnx2x_cyclecounter_read;
+ bp->cyclecounter.mask = CLOCKSOURCE_MASK(64);
+ bp->cyclecounter.shift = 1;
+ bp->cyclecounter.mult = 1;
+}
+
+static int bnx2x_send_reset_timesync_ramrod(struct bnx2x *bp)
+{
+ struct bnx2x_func_state_params func_params = {NULL};
+ struct bnx2x_func_set_timesync_params *set_timesync_params =
+ &func_params.params.set_timesync;
+
+ /* Prepare parameters for function state transitions */
+ __set_bit(RAMROD_COMP_WAIT, &func_params.ramrod_flags);
+ __set_bit(RAMROD_RETRY, &func_params.ramrod_flags);
+
+ func_params.f_obj = &bp->func_obj;
+ func_params.cmd = BNX2X_F_CMD_SET_TIMESYNC;
+
+ /* Function parameters */
+ set_timesync_params->drift_adjust_cmd = TS_DRIFT_ADJUST_RESET;
+ set_timesync_params->offset_cmd = TS_OFFSET_KEEP;
+
+ return bnx2x_func_state_change(bp, &func_params);
+}
+
+int bnx2x_enable_ptp_packets(struct bnx2x *bp)
+{
+ struct bnx2x_queue_state_params q_params;
+ int rc, i;
+
+ /* send queue update ramrod to enable PTP packets */
+ memset(&q_params, 0, sizeof(q_params));
+ __set_bit(RAMROD_COMP_WAIT, &q_params.ramrod_flags);
+ q_params.cmd = BNX2X_Q_CMD_UPDATE;
+ __set_bit(BNX2X_Q_UPDATE_PTP_PKTS_CHNG,
+ &q_params.params.update.update_flags);
+ __set_bit(BNX2X_Q_UPDATE_PTP_PKTS,
+ &q_params.params.update.update_flags);
+
+ /* send the ramrod on all the queues of the PF */
+ for_each_eth_queue(bp, i) {
+ struct bnx2x_fastpath *fp = &bp->fp[i];
+
+ /* Set the appropriate Queue object */
+ q_params.q_obj = &bnx2x_sp_obj(bp, fp).q_obj;
+
+ /* Update the Queue state */
+ rc = bnx2x_queue_state_change(bp, &q_params);
+ if (rc) {
+ BNX2X_ERR("Failed to enable PTP packets\n");
+ return rc;
+ }
+ }
+
+ return 0;
+}
+
+int bnx2x_configure_ptp_filters(struct bnx2x *bp)
+{
+ int port = BP_PORT(bp);
+ int rc;
+
+ if (!bp->hwtstamp_ioctl_called)
+ return 0;
+
+ switch (bp->tx_type) {
+ case HWTSTAMP_TX_ON:
+ bp->flags |= TX_TIMESTAMPING_EN;
+ REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_PARAM_MASK :
+ NIG_REG_P0_TLLH_PTP_PARAM_MASK, 0x6AA);
+ REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_RULE_MASK :
+ NIG_REG_P0_TLLH_PTP_RULE_MASK, 0x3EEE);
+ break;
+ case HWTSTAMP_TX_ONESTEP_SYNC:
+ BNX2X_ERR("One-step timestamping is not supported\n");
+ return -ERANGE;
+ }
+
+ switch (bp->rx_filter) {
+ case HWTSTAMP_FILTER_NONE:
+ break;
+ case HWTSTAMP_FILTER_ALL:
+ case HWTSTAMP_FILTER_SOME:
+ bp->rx_filter = HWTSTAMP_FILTER_NONE;
+ break;
+ case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
+ case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
+ case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
+ bp->rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
+ /* Initialize PTP detection for UDP/IPv4 events */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+ NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x7EE);
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+ NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3FFE);
+ break;
+ case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
+ case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
+ case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
+ bp->rx_filter = HWTSTAMP_FILTER_PTP_V2_L4_EVENT;
+ /* Initialize PTP detection for UDP/IPv4 or UDP/IPv6 events */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+ NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x7EA);
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+ NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3FEE);
+ break;
+ case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
+ case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
+ case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
+ bp->rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
+ /* Initialize PTP detection L2 events */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+ NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x6BF);
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+ NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3EFF);
+
+ break;
+ case HWTSTAMP_FILTER_PTP_V2_EVENT:
+ case HWTSTAMP_FILTER_PTP_V2_SYNC:
+ case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
+ bp->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
+ /* Initialize PTP detection L2, UDP/IPv4 or UDP/IPv6 events */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+ NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x6AA);
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+ NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3EEE);
+ break;
+ }
+
+ /* Indicate to FW that this PF expects recorded PTP packets */
+ rc = bnx2x_enable_ptp_packets(bp);
+ if (rc)
+ return rc;
+
+ /* Enable sending PTP packets to host */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_TO_HOST :
+ NIG_REG_P0_LLH_PTP_TO_HOST, 0x1);
+
+ return 0;
+}
+
+static int bnx2x_hwtstamp_ioctl(struct bnx2x *bp, struct ifreq *ifr)
+{
+ struct hwtstamp_config config;
+ int rc;
+
+ DP(BNX2X_MSG_PTP, "HWTSTAMP IOCTL called\n");
+
+ if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
+ return -EFAULT;
+
+ DP(BNX2X_MSG_PTP, "Requested tx_type: %d, requested rx_filters = %d\n",
+ config.tx_type, config.rx_filter);
+
+ if (config.flags) {
+ BNX2X_ERR("config.flags is reserved for future use\n");
+ return -EINVAL;
+ }
+
+ bp->hwtstamp_ioctl_called = 1;
+ bp->tx_type = config.tx_type;
+ bp->rx_filter = config.rx_filter;
+
+ rc = bnx2x_configure_ptp_filters(bp);
+ if (rc)
+ return rc;
+
+ config.rx_filter = bp->rx_filter;
+
+ return copy_to_user(ifr->ifr_data, &config, sizeof(config)) ?
+ -EFAULT : 0;
+}
+
+/* Configrues HW for PTP */
+static int bnx2x_configure_ptp(struct bnx2x *bp)
+{
+ int rc, port = BP_PORT(bp);
+ u32 wb_data[2];
+
+ /* Reset PTP event detection rules - will be configured in the IOCTL */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+ NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x7FF);
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+ NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3FFF);
+ REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_PARAM_MASK :
+ NIG_REG_P0_TLLH_PTP_PARAM_MASK, 0x7FF);
+ REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_RULE_MASK :
+ NIG_REG_P0_TLLH_PTP_RULE_MASK, 0x3FFF);
+
+ /* Disable PTP packets to host - will be configured in the IOCTL*/
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_TO_HOST :
+ NIG_REG_P0_LLH_PTP_TO_HOST, 0x0);
+
+ /* Enable the PTP feature */
+ REG_WR(bp, port ? NIG_REG_P1_PTP_EN :
+ NIG_REG_P0_PTP_EN, 0x3F);
+
+ /* Enable the free-running counter */
+ wb_data[0] = 0;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, NIG_REG_TIMESYNC_GEN_REG + tsgen_ctrl, wb_data, 2);
+
+ /* Reset drift register (offset register is not reset) */
+ rc = bnx2x_send_reset_timesync_ramrod(bp);
+ if (rc) {
+ BNX2X_ERR("Failed to reset PHC drift register\n");
+ return -EFAULT;
+ }
+
+ /* Reset possibly old timestamps */
+ REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID :
+ NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID, 0x10000);
+ REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_SEQID :
+ NIG_REG_P0_TLLH_PTP_BUF_SEQID, 0x10000);
+
+ return 0;
+}
+
+/* Called during load, to initialize PTP-related stuff */
+void bnx2x_init_ptp(struct bnx2x *bp)
+{
+ int rc;
+
+ /* Configure PTP in HW */
+ rc = bnx2x_configure_ptp(bp);
+ if (rc) {
+ BNX2X_ERR("Stopping PTP initialization\n");
+ return;
+ }
+
+ /* Init work queue for Tx timestamping */
+ INIT_WORK(&bp->ptp_task, bnx2x_ptp_task);
+
+ /* Init cyclecounter and timecounter. This is done only in the first
+ * load. If done in every load, PTP application will fail when doing
+ * unload / load (e.g. MTU change) while it is running.
+ */
+ if (!bp->timecounter_init_done) {
+ bnx2x_init_cyclecounter(bp);
+ timecounter_init(&bp->timecounter, &bp->cyclecounter,
+ ktime_to_ns(ktime_get_real()));
+ bp->timecounter_init_done = 1;
+ }
+
+ DP(BNX2X_MSG_PTP, "PTP initialization ended successfully\n");
+}
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
index 2beb543..b0779d7 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h
@@ -2182,6 +2182,45 @@
#define NIG_REG_P0_HWPFC_ENABLE 0x18078
#define NIG_REG_P0_LLH_FUNC_MEM2 0x18480
#define NIG_REG_P0_LLH_FUNC_MEM2_ENABLE 0x18440
+/* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. Bits [15:0] return the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Writing a 1 to bit 16
+ * will clear the buffer.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID 0x1875c
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_LSB 0x18754
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_MSB 0x18758
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P0_LLH_PTP_PARAM_MASK 0x187a0
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules. Note that rules 0-3 are for IPv4
+ * packets only and require that the packet is IPv4 for the rules to match.
+ * Note that rules 4-7 are for IPv6 packets only and require that the packet
+ * is IPv6 for the rules to match.
+ */
+#define NIG_REG_P0_LLH_PTP_RULE_MASK 0x187a4
+/* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */
+#define NIG_REG_P0_LLH_PTP_TO_HOST 0x187ac
/* [RW 1] Input enable for RX MAC interface. */
#define NIG_REG_P0_MAC_IN_EN 0x185ac
/* [RW 1] Output enable for TX MAC interface */
@@ -2194,6 +2233,17 @@
* priority field is extracted from the outer-most VLAN in receive packet.
* Only COS 0 and COS 1 are supported in E2. */
#define NIG_REG_P0_PKT_PRIORITY_TO_COS 0x18054
+/* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits
+ * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables
+ * V1 frame format in timesync event detection on RX side. Bit 2 enables V2
+ * frame format in timesync event detection on RX side. Bit 3 enables
+ * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event
+ * detection on TX side. Bit 5 enables V2 frame format in timesync event
+ * detection on TX side. Note that for HW to detect PTP packet and extract
+ * data from the packet, at least one of the version bits of that traffic
+ * direction has to be enabled.
+ */
+#define NIG_REG_P0_PTP_EN 0x18788
/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A
* priority is mapped to COS 0 when the corresponding mask bit is 1. More
* than one bit may be set; allowing multiple priorities to be mapped to one
@@ -2300,7 +2350,46 @@
* Ethernet header. */
#define NIG_REG_P1_HDRS_AFTER_BASIC 0x1818c
#define NIG_REG_P1_LLH_FUNC_MEM2 0x184c0
-#define NIG_REG_P1_LLH_FUNC_MEM2_ENABLE 0x18460
+#define NIG_REG_P1_LLH_FUNC_MEM2_ENABLE 0x18460a
+/* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. Bits [15:0] return the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Writing a 1 to bit 16
+ * will clear the buffer.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID 0x18774
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_LSB 0x1876c
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_MSB 0x18770
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P1_LLH_PTP_PARAM_MASK 0x187c8
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules. Note that rules 0-3 are for IPv4
+ * packets only and require that the packet is IPv4 for the rules to match.
+ * Note that rules 4-7 are for IPv6 packets only and require that the packet
+ * is IPv6 for the rules to match.
+ */
+#define NIG_REG_P1_LLH_PTP_RULE_MASK 0x187cc
+/* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */
+#define NIG_REG_P1_LLH_PTP_TO_HOST 0x187d4
/* [RW 32] Specify the client number to be assigned to each priority of the
* strict priority arbiter. This register specifies bits 31:0 of the 36-bit
* value. Priority 0 is the highest priority. Bits [3:0] are for priority 0
@@ -2342,6 +2431,17 @@
* priority field is extracted from the outer-most VLAN in receive packet.
* Only COS 0 and COS 1 are supported in E2. */
#define NIG_REG_P1_PKT_PRIORITY_TO_COS 0x181a8
+/* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits
+ * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables
+ * V1 frame format in timesync event detection on RX side. Bit 2 enables V2
+ * frame format in timesync event detection on RX side. Bit 3 enables
+ * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event
+ * detection on TX side. Bit 5 enables V2 frame format in timesync event
+ * detection on TX side. Note that for HW to detect PTP packet and extract
+ * data from the packet, at least one of the version bits of that traffic
+ * direction has to be enabled.
+ */
+#define NIG_REG_P1_PTP_EN 0x187b0
/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A
* priority is mapped to COS 0 when the corresponding mask bit is 1. More
* than one bit may be set; allowing multiple priorities to be mapped to one
@@ -2361,6 +2461,78 @@
#define NIG_REG_P1_RX_MACFIFO_EMPTY 0x1858c
/* [R 1] TLLH FIFO is empty. */
#define NIG_REG_P1_TLLH_FIFO_EMPTY 0x18338
+/* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Bit 17 indicates that
+ * the sequence ID is valid and it is waiting for the TX timestamp value.
+ * Bit 18 indicates whether the timestamp is from a SW request (value of 1)
+ * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_SEQID 0x187e0
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_TS_LSB 0x187d8
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_TS_MSB 0x187dc
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P0_TLLH_PTP_PARAM_MASK 0x187f0
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules.
+ */
+#define NIG_REG_P0_TLLH_PTP_RULE_MASK 0x187f4
+/* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Bit 17 indicates that
+ * the sequence ID is valid and it is waiting for the TX timestamp value.
+ * Bit 18 indicates whether the timestamp is from a SW request (value of 1)
+ * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_SEQID 0x187ec
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_TS_LSB 0x187e4
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_TS_MSB 0x187e8
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P1_TLLH_PTP_PARAM_MASK 0x187f8
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules.
+ */
+#define NIG_REG_P1_TLLH_PTP_RULE_MASK 0x187fc
/* [RW 32] Specify which of the credit registers the client is to be mapped
* to. This register specifies bits 31:0 of the 36-bit value. Bits[3:0] are
* for client 0; bits [35:32] are for client 8. For clients that are not
@@ -2513,6 +2685,10 @@
swap is equal to SPIO pin that inputs from ifmux_serdes_swap. If 1 then
ort swap is equal to ~nig_registers_port_swap.port_swap */
#define NIG_REG_STRAP_OVERRIDE 0x10398
+/* [WB 64] Addresses for TimeSync related registers in the timesync
+ * generator sub-module.
+ */
+#define NIG_REG_TIMESYNC_GEN_REG 0x18800
/* [RW 1] output enable for RX_XCM0 IF */
#define NIG_REG_XCM0_OUT_EN 0x100f0
/* [RW 1] output enable for RX_XCM1 IF */
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c
index d825ef6..798e97f 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c
@@ -4725,6 +4725,12 @@ static void bnx2x_q_fill_update_data(struct bnx2x *bp,
data->tx_switching_change_flg =
test_bit(BNX2X_Q_UPDATE_TX_SWITCHING_CHNG,
¶ms->update_flags);
+
+ /* PTP */
+ data->handle_ptp_pkts_flg =
+ test_bit(BNX2X_Q_UPDATE_PTP_PKTS, ¶ms->update_flags);
+ data->handle_ptp_pkts_change_flg =
+ test_bit(BNX2X_Q_UPDATE_PTP_PKTS_CHNG, ¶ms->update_flags);
}
static inline int bnx2x_q_send_update(struct bnx2x *bp,
@@ -5379,6 +5385,10 @@ static int bnx2x_func_chk_transition(struct bnx2x *bp,
(!test_bit(BNX2X_F_CMD_STOP, &o->pending)))
next_state = BNX2X_F_STATE_STARTED;
+ else if ((cmd == BNX2X_F_CMD_SET_TIMESYNC) &&
+ (!test_bit(BNX2X_F_CMD_STOP, &o->pending)))
+ next_state = BNX2X_F_STATE_STARTED;
+
else if (cmd == BNX2X_F_CMD_TX_STOP)
next_state = BNX2X_F_STATE_TX_STOPPED;
@@ -5388,6 +5398,10 @@ static int bnx2x_func_chk_transition(struct bnx2x *bp,
(!test_bit(BNX2X_F_CMD_STOP, &o->pending)))
next_state = BNX2X_F_STATE_TX_STOPPED;
+ else if ((cmd == BNX2X_F_CMD_SET_TIMESYNC) &&
+ (!test_bit(BNX2X_F_CMD_STOP, &o->pending)))
+ next_state = BNX2X_F_STATE_TX_STOPPED;
+
else if (cmd == BNX2X_F_CMD_TX_START)
next_state = BNX2X_F_STATE_STARTED;
@@ -5843,6 +5857,40 @@ static inline int bnx2x_func_send_tx_start(struct bnx2x *bp,
U64_LO(data_mapping), NONE_CONNECTION_TYPE);
}
+static inline
+int bnx2x_func_send_set_timesync(struct bnx2x *bp,
+ struct bnx2x_func_state_params *params)
+{
+ struct bnx2x_func_sp_obj *o = params->f_obj;
+ struct set_timesync_ramrod_data *rdata =
+ (struct set_timesync_ramrod_data *)o->rdata;
+ dma_addr_t data_mapping = o->rdata_mapping;
+ struct bnx2x_func_set_timesync_params *set_timesync_params =
+ ¶ms->params.set_timesync;
+
+ memset(rdata, 0, sizeof(*rdata));
+
+ /* Fill the ramrod data with provided parameters */
+ rdata->drift_adjust_cmd = set_timesync_params->drift_adjust_cmd;
+ rdata->offset_cmd = set_timesync_params->offset_cmd;
+ rdata->add_sub_drift_adjust_value =
+ set_timesync_params->add_sub_drift_adjust_value;
+ rdata->drift_adjust_value = set_timesync_params->drift_adjust_value;
+ rdata->drift_adjust_period = set_timesync_params->drift_adjust_period;
+ rdata->offset_delta.lo = U64_LO(set_timesync_params->offset_delta);
+ rdata->offset_delta.hi = U64_HI(set_timesync_params->offset_delta);
+
+ DP(BNX2X_MSG_SP, "Set timesync command params: drift_cmd = %d, offset_cmd = %d, add_sub_drift = %d, drift_val = %d, drift_period = %d, offset_lo = %d, offset_hi = %d\n",
+ rdata->drift_adjust_cmd, rdata->offset_cmd,
+ rdata->add_sub_drift_adjust_value, rdata->drift_adjust_value,
+ rdata->drift_adjust_period, rdata->offset_delta.lo,
+ rdata->offset_delta.hi);
+
+ return bnx2x_sp_post(bp, RAMROD_CMD_ID_COMMON_SET_TIMESYNC, 0,
+ U64_HI(data_mapping),
+ U64_LO(data_mapping), NONE_CONNECTION_TYPE);
+}
+
static int bnx2x_func_send_cmd(struct bnx2x *bp,
struct bnx2x_func_state_params *params)
{
@@ -5865,6 +5913,8 @@ static int bnx2x_func_send_cmd(struct bnx2x *bp,
return bnx2x_func_send_tx_start(bp, params);
case BNX2X_F_CMD_SWITCH_UPDATE:
return bnx2x_func_send_switch_update(bp, params);
+ case BNX2X_F_CMD_SET_TIMESYNC:
+ return bnx2x_func_send_set_timesync(bp, params);
default:
BNX2X_ERR("Unknown command: %d\n", params->cmd);
return -EINVAL;
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h
index 5ac247d..21c8f6f 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h
@@ -770,7 +770,9 @@ enum {
BNX2X_Q_UPDATE_SILENT_VLAN_REM_CHNG,
BNX2X_Q_UPDATE_SILENT_VLAN_REM,
BNX2X_Q_UPDATE_TX_SWITCHING_CHNG,
- BNX2X_Q_UPDATE_TX_SWITCHING
+ BNX2X_Q_UPDATE_TX_SWITCHING,
+ BNX2X_Q_UPDATE_PTP_PKTS_CHNG,
+ BNX2X_Q_UPDATE_PTP_PKTS,
};
/* Allowed Queue states */
@@ -853,6 +855,10 @@ enum bnx2x_q_type {
#define BNX2X_MULTI_TX_COS 3 /* Maximum possible */
#define MAC_PAD (ALIGN(ETH_ALEN, sizeof(u32)) - ETH_ALEN)
+/* DMAE channel to be used by FW for timesync workaroun. A driver that sends
+ * timesync-related ramrods must not use this DMAE command ID.
+ */
+#define FW_DMAE_CMD_ID 6
struct bnx2x_queue_init_params {
struct {
@@ -1117,6 +1123,7 @@ enum bnx2x_func_cmd {
BNX2X_F_CMD_TX_STOP,
BNX2X_F_CMD_TX_START,
BNX2X_F_CMD_SWITCH_UPDATE,
+ BNX2X_F_CMD_SET_TIMESYNC,
BNX2X_F_CMD_MAX,
};
@@ -1191,6 +1198,7 @@ struct bnx2x_func_afex_viflists_params {
u8 afex_vif_list_command;
u8 func_to_clear;
};
+
struct bnx2x_func_tx_start_params {
struct priority_cos traffic_type_to_priority_cos[MAX_TRAFFIC_TYPES];
u8 dcb_enabled;
@@ -1198,6 +1206,24 @@ struct bnx2x_func_tx_start_params {
u8 dont_add_pri_0_en;
};
+struct bnx2x_func_set_timesync_params {
+ /* Reset, set or keep the current drift value */
+ u8 drift_adjust_cmd;
+
+ /* Dec, inc or keep the current offset */
+ u8 offset_cmd;
+
+ /* Drift value direction */
+ u8 add_sub_drift_adjust_value;
+
+ /* Drift, period and offset values to be used according to the commands
+ * above.
+ */
+ u8 drift_adjust_value;
+ u32 drift_adjust_period;
+ u64 offset_delta;
+};
+
struct bnx2x_func_state_params {
struct bnx2x_func_sp_obj *f_obj;
@@ -1216,6 +1242,7 @@ struct bnx2x_func_state_params {
struct bnx2x_func_afex_update_params afex_update;
struct bnx2x_func_afex_viflists_params afex_viflists;
struct bnx2x_func_tx_start_params tx_start;
+ struct bnx2x_func_set_timesync_params set_timesync;
} params;
};
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists