| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <54B686FA.2060001@atmel.com> Date: Wed, 14 Jan 2015 16:10:50 +0100 From: Nicolas Ferre <nicolas.ferre@...el.com> To: Xander Huff <xander.huff@...com> CC: <jaeden.amero@...com>, <rich.tollerton@...com>, <ben.shelton@...com>, <brad.mouring@...com>, <netdev@...r.kernel.org>, <linux-kernel@...r.kernel.org> Subject: Re: [PATCH 1/2] net/macb: Adding comments to various #defs to make interpretation easier Le 13/01/2015 23:15, Xander Huff a écrit : > This change is to help improve at-a-glace knowledge of the purpose of the > various Cadence MACB/GEM registers. Comments are more helpful for human > readability than short acronyms. > > Describe various #define varibles Cadence MACB/GEM registers as documented > in Xilinix's "Zynq-7000 All Programmable SoC TechnicalReference Manual, v1.9.1 > (UG-585)" > > Signed-off-by: Xander Huff <xander.huff@...com> For the record: Acked-by: Nicolas Ferre <nicolas.ferre@...el.com> > --- > drivers/net/ethernet/cadence/macb.h | 269 ++++++++++++++++++++++-------------- > 1 file changed, 162 insertions(+), 107 deletions(-) > > diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h > index 084191b..8e8c3c9 100644 > --- a/drivers/net/ethernet/cadence/macb.h > +++ b/drivers/net/ethernet/cadence/macb.h > @@ -15,20 +15,20 @@ > #define MACB_MAX_QUEUES 8 > > /* MACB register offsets */ > -#define MACB_NCR 0x0000 > -#define MACB_NCFGR 0x0004 > -#define MACB_NSR 0x0008 > +#define MACB_NCR 0x0000 /* Network Control */ > +#define MACB_NCFGR 0x0004 /* Network Config */ > +#define MACB_NSR 0x0008 /* Network Status */ > #define MACB_TAR 0x000c /* AT91RM9200 only */ > #define MACB_TCR 0x0010 /* AT91RM9200 only */ > -#define MACB_TSR 0x0014 > -#define MACB_RBQP 0x0018 > -#define MACB_TBQP 0x001c > -#define MACB_RSR 0x0020 > -#define MACB_ISR 0x0024 > -#define MACB_IER 0x0028 > -#define MACB_IDR 0x002c > -#define MACB_IMR 0x0030 > -#define MACB_MAN 0x0034 > +#define MACB_TSR 0x0014 /* Transmit Status */ > +#define MACB_RBQP 0x0018 /* RX Q Base Address */ > +#define MACB_TBQP 0x001c /* TX Q Base Address */ > +#define MACB_RSR 0x0020 /* Receive Status */ > +#define MACB_ISR 0x0024 /* Interrupt Status */ > +#define MACB_IER 0x0028 /* Interrupt Enable */ > +#define MACB_IDR 0x002c /* Interrupt Disable */ > +#define MACB_IMR 0x0030 /* Interrupt Mask */ > +#define MACB_MAN 0x0034 /* PHY Maintenance */ > #define MACB_PTR 0x0038 > #define MACB_PFR 0x003c > #define MACB_FTO 0x0040 > @@ -68,27 +68,27 @@ > #define MACB_MID 0x00fc > > /* GEM register offsets. */ > -#define GEM_NCFGR 0x0004 > -#define GEM_USRIO 0x000c > -#define GEM_DMACFG 0x0010 > -#define GEM_HRB 0x0080 > -#define GEM_HRT 0x0084 > -#define GEM_SA1B 0x0088 > -#define GEM_SA1T 0x008C > -#define GEM_SA2B 0x0090 > -#define GEM_SA2T 0x0094 > -#define GEM_SA3B 0x0098 > -#define GEM_SA3T 0x009C > -#define GEM_SA4B 0x00A0 > -#define GEM_SA4T 0x00A4 > -#define GEM_OTX 0x0100 > -#define GEM_DCFG1 0x0280 > -#define GEM_DCFG2 0x0284 > -#define GEM_DCFG3 0x0288 > -#define GEM_DCFG4 0x028c > -#define GEM_DCFG5 0x0290 > -#define GEM_DCFG6 0x0294 > -#define GEM_DCFG7 0x0298 > +#define GEM_NCFGR 0x0004 /* Network Config */ > +#define GEM_USRIO 0x000c /* User IO */ > +#define GEM_DMACFG 0x0010 /* DMA Configuration */ > +#define GEM_HRB 0x0080 /* Hash Bottom */ > +#define GEM_HRT 0x0084 /* Hash Top */ > +#define GEM_SA1B 0x0088 /* Specific1 Bottom */ > +#define GEM_SA1T 0x008C /* Specific1 Top */ > +#define GEM_SA2B 0x0090 /* Specific2 Bottom */ > +#define GEM_SA2T 0x0094 /* Specific2 Top */ > +#define GEM_SA3B 0x0098 /* Specific3 Bottom */ > +#define GEM_SA3T 0x009C /* Specific3 Top */ > +#define GEM_SA4B 0x00A0 /* Specific4 Bottom */ > +#define GEM_SA4T 0x00A4 /* Specific4 Top */ > +#define GEM_OTX 0x0100 /* Octets transmitted */ > +#define GEM_DCFG1 0x0280 /* Design Config 1 */ > +#define GEM_DCFG2 0x0284 /* Design Config 2 */ > +#define GEM_DCFG3 0x0288 /* Design Config 3 */ > +#define GEM_DCFG4 0x028c /* Design Config 4 */ > +#define GEM_DCFG5 0x0290 /* Design Config 5 */ > +#define GEM_DCFG6 0x0294 /* Design Config 6 */ > +#define GEM_DCFG7 0x0298 /* Design Config 7 */ > > #define GEM_ISR(hw_q) (0x0400 + ((hw_q) << 2)) > #define GEM_TBQP(hw_q) (0x0440 + ((hw_q) << 2)) > @@ -98,67 +98,73 @@ > #define GEM_IMR(hw_q) (0x0640 + ((hw_q) << 2)) > > /* Bitfields in NCR */ > -#define MACB_LB_OFFSET 0 > +#define MACB_LB_OFFSET 0 /* reserved */ > #define MACB_LB_SIZE 1 > -#define MACB_LLB_OFFSET 1 > +#define MACB_LLB_OFFSET 1 /* Loop back local */ > #define MACB_LLB_SIZE 1 > -#define MACB_RE_OFFSET 2 > +#define MACB_RE_OFFSET 2 /* Receive enable */ > #define MACB_RE_SIZE 1 > -#define MACB_TE_OFFSET 3 > +#define MACB_TE_OFFSET 3 /* Transmit enable */ > #define MACB_TE_SIZE 1 > -#define MACB_MPE_OFFSET 4 > +#define MACB_MPE_OFFSET 4 /* Management port enable */ > #define MACB_MPE_SIZE 1 > -#define MACB_CLRSTAT_OFFSET 5 > +#define MACB_CLRSTAT_OFFSET 5 /* Clear stats regs */ > #define MACB_CLRSTAT_SIZE 1 > -#define MACB_INCSTAT_OFFSET 6 > +#define MACB_INCSTAT_OFFSET 6 /* Incremental stats regs */ > #define MACB_INCSTAT_SIZE 1 > -#define MACB_WESTAT_OFFSET 7 > +#define MACB_WESTAT_OFFSET 7 /* Write enable stats regs */ > #define MACB_WESTAT_SIZE 1 > -#define MACB_BP_OFFSET 8 > +#define MACB_BP_OFFSET 8 /* Back pressure */ > #define MACB_BP_SIZE 1 > -#define MACB_TSTART_OFFSET 9 > +#define MACB_TSTART_OFFSET 9 /* Start transmission */ > #define MACB_TSTART_SIZE 1 > -#define MACB_THALT_OFFSET 10 > +#define MACB_THALT_OFFSET 10 /* Transmit halt */ > #define MACB_THALT_SIZE 1 > -#define MACB_NCR_TPF_OFFSET 11 > +#define MACB_NCR_TPF_OFFSET 11 /* Transmit pause frame */ > #define MACB_NCR_TPF_SIZE 1 > -#define MACB_TZQ_OFFSET 12 > +#define MACB_TZQ_OFFSET 12 /* Transmit zero quantum > + * pause frame > + */ > #define MACB_TZQ_SIZE 1 > > /* Bitfields in NCFGR */ > -#define MACB_SPD_OFFSET 0 > +#define MACB_SPD_OFFSET 0 /* Speed */ > #define MACB_SPD_SIZE 1 > -#define MACB_FD_OFFSET 1 > +#define MACB_FD_OFFSET 1 /* Full duplex */ > #define MACB_FD_SIZE 1 > -#define MACB_BIT_RATE_OFFSET 2 > +#define MACB_BIT_RATE_OFFSET 2 /* Discard non-VLAN frames */ > #define MACB_BIT_RATE_SIZE 1 > -#define MACB_JFRAME_OFFSET 3 > +#define MACB_JFRAME_OFFSET 3 /* reserved */ > #define MACB_JFRAME_SIZE 1 > -#define MACB_CAF_OFFSET 4 > +#define MACB_CAF_OFFSET 4 /* Copy all frames */ > #define MACB_CAF_SIZE 1 > -#define MACB_NBC_OFFSET 5 > +#define MACB_NBC_OFFSET 5 /* No broadcast */ > #define MACB_NBC_SIZE 1 > -#define MACB_NCFGR_MTI_OFFSET 6 > +#define MACB_NCFGR_MTI_OFFSET 6 /* Multicast hash enable */ > #define MACB_NCFGR_MTI_SIZE 1 > -#define MACB_UNI_OFFSET 7 > +#define MACB_UNI_OFFSET 7 /* Unicast hash enable */ > #define MACB_UNI_SIZE 1 > -#define MACB_BIG_OFFSET 8 > +#define MACB_BIG_OFFSET 8 /* Receive 1536 byte frames */ > #define MACB_BIG_SIZE 1 > -#define MACB_EAE_OFFSET 9 > +#define MACB_EAE_OFFSET 9 /* External address match > + * enable > + */ > #define MACB_EAE_SIZE 1 > #define MACB_CLK_OFFSET 10 > #define MACB_CLK_SIZE 2 > -#define MACB_RTY_OFFSET 12 > +#define MACB_RTY_OFFSET 12 /* Retry test */ > #define MACB_RTY_SIZE 1 > -#define MACB_PAE_OFFSET 13 > +#define MACB_PAE_OFFSET 13 /* Pause enable */ > #define MACB_PAE_SIZE 1 > #define MACB_RM9200_RMII_OFFSET 13 /* AT91RM9200 only */ > #define MACB_RM9200_RMII_SIZE 1 /* AT91RM9200 only */ > -#define MACB_RBOF_OFFSET 14 > +#define MACB_RBOF_OFFSET 14 /* Receive buffer offset */ > #define MACB_RBOF_SIZE 2 > -#define MACB_RLCE_OFFSET 16 > +#define MACB_RLCE_OFFSET 16 /* Length field error frame > + * discard > + */ > #define MACB_RLCE_SIZE 1 > -#define MACB_DRFCS_OFFSET 17 > +#define MACB_DRFCS_OFFSET 17 /* FCS remove */ > #define MACB_DRFCS_SIZE 1 > #define MACB_EFRHD_OFFSET 18 > #define MACB_EFRHD_SIZE 1 > @@ -166,111 +172,160 @@ > #define MACB_IRXFCS_SIZE 1 > > /* GEM specific NCFGR bitfields. */ > -#define GEM_GBE_OFFSET 10 > +#define GEM_GBE_OFFSET 10 /* Gigabit mode enable */ > #define GEM_GBE_SIZE 1 > -#define GEM_CLK_OFFSET 18 > +#define GEM_CLK_OFFSET 18 /* MDC clock division */ > #define GEM_CLK_SIZE 3 > -#define GEM_DBW_OFFSET 21 > +#define GEM_DBW_OFFSET 21 /* Data bus width */ > #define GEM_DBW_SIZE 2 > #define GEM_RXCOEN_OFFSET 24 > #define GEM_RXCOEN_SIZE 1 > > /* Constants for data bus width. */ > -#define GEM_DBW32 0 > -#define GEM_DBW64 1 > -#define GEM_DBW128 2 > +#define GEM_DBW32 0 /* 32 bit AMBA AHB data bus > + * width > + */ > +#define GEM_DBW64 1 /* 64 bit AMBA AHB data bus > + * width > + */ > +#define GEM_DBW128 2 /* 128 bit AMBA AHB data bus > + * width > + */ > > /* Bitfields in DMACFG. */ > -#define GEM_FBLDO_OFFSET 0 > +#define GEM_FBLDO_OFFSET 0 /* AHB fixed burst length for > + * DMA data operations > + */ > #define GEM_FBLDO_SIZE 5 > -#define GEM_ENDIA_OFFSET 7 > +#define GEM_ENDIA_OFFSET 7 /* AHB endian swap mode enable > + * for packet data accesses > + */ > #define GEM_ENDIA_SIZE 1 > -#define GEM_RXBMS_OFFSET 8 > +#define GEM_RXBMS_OFFSET 8 /* Receiver packet buffer > + * memory size select > + */ > #define GEM_RXBMS_SIZE 2 > -#define GEM_TXPBMS_OFFSET 10 > +#define GEM_TXPBMS_OFFSET 10 /* Transmitter packet buffer > + * memory size select > + */ > #define GEM_TXPBMS_SIZE 1 > -#define GEM_TXCOEN_OFFSET 11 > +#define GEM_TXCOEN_OFFSET 11 /* Transmitter IP, TCP and > + * UDP checksum generation > + * offload enable > + */ > #define GEM_TXCOEN_SIZE 1 > -#define GEM_RXBS_OFFSET 16 > +#define GEM_RXBS_OFFSET 16 /* DMA receive buffer size in > + * AHB system memory > + */ > #define GEM_RXBS_SIZE 8 > -#define GEM_DDRP_OFFSET 24 > +#define GEM_DDRP_OFFSET 24 /* disc_when_no_ahb */ > #define GEM_DDRP_SIZE 1 > > > /* Bitfields in NSR */ > -#define MACB_NSR_LINK_OFFSET 0 > +#define MACB_NSR_LINK_OFFSET 0 /* pcs_link_state */ > #define MACB_NSR_LINK_SIZE 1 > -#define MACB_MDIO_OFFSET 1 > +#define MACB_MDIO_OFFSET 1 /* status of the mdio_in > + * pin > + */ > #define MACB_MDIO_SIZE 1 > -#define MACB_IDLE_OFFSET 2 > +#define MACB_IDLE_OFFSET 2 /* The PHY management logic is > + * idle (i.e. has completed) > + */ > #define MACB_IDLE_SIZE 1 > > /* Bitfields in TSR */ > -#define MACB_UBR_OFFSET 0 > +#define MACB_UBR_OFFSET 0 /* Used bit read */ > #define MACB_UBR_SIZE 1 > -#define MACB_COL_OFFSET 1 > +#define MACB_COL_OFFSET 1 /* Collision occurred */ > #define MACB_COL_SIZE 1 > -#define MACB_TSR_RLE_OFFSET 2 > +#define MACB_TSR_RLE_OFFSET 2 /* Retry limit exceeded */ > #define MACB_TSR_RLE_SIZE 1 > -#define MACB_TGO_OFFSET 3 > +#define MACB_TGO_OFFSET 3 /* Transmit go */ > #define MACB_TGO_SIZE 1 > -#define MACB_BEX_OFFSET 4 > +#define MACB_BEX_OFFSET 4 /* Transmit frame corruption > + * due to AHB error > + */ > #define MACB_BEX_SIZE 1 > #define MACB_RM9200_BNQ_OFFSET 4 /* AT91RM9200 only */ > #define MACB_RM9200_BNQ_SIZE 1 /* AT91RM9200 only */ > -#define MACB_COMP_OFFSET 5 > +#define MACB_COMP_OFFSET 5 /* Trnasmit complete */ > #define MACB_COMP_SIZE 1 > -#define MACB_UND_OFFSET 6 > +#define MACB_UND_OFFSET 6 /* Trnasmit under run */ > #define MACB_UND_SIZE 1 > > /* Bitfields in RSR */ > -#define MACB_BNA_OFFSET 0 > +#define MACB_BNA_OFFSET 0 /* Buffer not available */ > #define MACB_BNA_SIZE 1 > -#define MACB_REC_OFFSET 1 > +#define MACB_REC_OFFSET 1 /* Frame received */ > #define MACB_REC_SIZE 1 > -#define MACB_OVR_OFFSET 2 > +#define MACB_OVR_OFFSET 2 /* Receive overrun */ > #define MACB_OVR_SIZE 1 > > /* Bitfields in ISR/IER/IDR/IMR */ > -#define MACB_MFD_OFFSET 0 > +#define MACB_MFD_OFFSET 0 /* Management frame sent */ > #define MACB_MFD_SIZE 1 > -#define MACB_RCOMP_OFFSET 1 > +#define MACB_RCOMP_OFFSET 1 /* Receive complete */ > #define MACB_RCOMP_SIZE 1 > -#define MACB_RXUBR_OFFSET 2 > +#define MACB_RXUBR_OFFSET 2 /* RX used bit read */ > #define MACB_RXUBR_SIZE 1 > -#define MACB_TXUBR_OFFSET 3 > +#define MACB_TXUBR_OFFSET 3 /* TX used bit read */ > #define MACB_TXUBR_SIZE 1 > -#define MACB_ISR_TUND_OFFSET 4 > +#define MACB_ISR_TUND_OFFSET 4 /* Enable trnasmit buffer > + * under run interrupt > + */ > #define MACB_ISR_TUND_SIZE 1 > -#define MACB_ISR_RLE_OFFSET 5 > +#define MACB_ISR_RLE_OFFSET 5 /* Enable retry limit exceeded > + * or late collision interrupt > + */ > #define MACB_ISR_RLE_SIZE 1 > -#define MACB_TXERR_OFFSET 6 > +#define MACB_TXERR_OFFSET 6 /* Enable transmit frame > + * corruption due to AHB error > + * interrupt > + */ > #define MACB_TXERR_SIZE 1 > -#define MACB_TCOMP_OFFSET 7 > +#define MACB_TCOMP_OFFSET 7 /* Enable transmit complete > + * interrupt > + */ > #define MACB_TCOMP_SIZE 1 > -#define MACB_ISR_LINK_OFFSET 9 > +#define MACB_ISR_LINK_OFFSET 9 /* Enable link change > + * interrupt > + */ > #define MACB_ISR_LINK_SIZE 1 > -#define MACB_ISR_ROVR_OFFSET 10 > +#define MACB_ISR_ROVR_OFFSET 10 /* Enable receive overrun > + * interrupt > + */ > #define MACB_ISR_ROVR_SIZE 1 > -#define MACB_HRESP_OFFSET 11 > +#define MACB_HRESP_OFFSET 11 /* Enable hrsep not OK > + * interrupt > + */ > #define MACB_HRESP_SIZE 1 > -#define MACB_PFR_OFFSET 12 > +#define MACB_PFR_OFFSET 12 /* Enable pause frame with > + * non-zero pause quantum > + * interrupt > + */ > #define MACB_PFR_SIZE 1 > -#define MACB_PTZ_OFFSET 13 > +#define MACB_PTZ_OFFSET 13 /* Enable pause time zero > + * interrupt > + */ > #define MACB_PTZ_SIZE 1 > > /* Bitfields in MAN */ > -#define MACB_DATA_OFFSET 0 > +#define MACB_DATA_OFFSET 0 /* data */ > #define MACB_DATA_SIZE 16 > -#define MACB_CODE_OFFSET 16 > +#define MACB_CODE_OFFSET 16 /* Must be written to 10 */ > #define MACB_CODE_SIZE 2 > -#define MACB_REGA_OFFSET 18 > +#define MACB_REGA_OFFSET 18 /* Register address */ > #define MACB_REGA_SIZE 5 > -#define MACB_PHYA_OFFSET 23 > +#define MACB_PHYA_OFFSET 23 /* PHY address */ > #define MACB_PHYA_SIZE 5 > -#define MACB_RW_OFFSET 28 > +#define MACB_RW_OFFSET 28 /* Operation. 10 is read. 01 > + * is write. > + */ > #define MACB_RW_SIZE 2 > -#define MACB_SOF_OFFSET 30 > +#define MACB_SOF_OFFSET 30 /* Must be written to 1 for > + * Clause 22 operation > + */ > #define MACB_SOF_SIZE 2 > > /* Bitfields in USRIO (AVR32) */ > @@ -286,7 +341,7 @@ > /* Bitfields in USRIO (AT91) */ > #define MACB_RMII_OFFSET 0 > #define MACB_RMII_SIZE 1 > -#define GEM_RGMII_OFFSET 0 /* GEM gigabit mode */ > +#define GEM_RGMII_OFFSET 0 /* GEM gigabit mode */ > #define GEM_RGMII_SIZE 1 > #define MACB_CLKEN_OFFSET 1 > #define MACB_CLKEN_SIZE 1 > -- Nicolas Ferre -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists