netdev - RE: [PATCH net-next 1/3] r8152: separate USB_RX_EARLY

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <0835B3720019904CB8F7AA43166CEEB2EE9373@RTITMBSV03.realtek.com.tw>
Date:	Thu, 12 Feb 2015 06:04:06 +0000
From:	Hayes Wang <hayeswang@...ltek.com>
To:	Hayes Wang <hayeswang@...ltek.com>,
	Sergei Shtylyov <sergei.shtylyov@...entembedded.com>,
	"netdev@...r.kernel.org" <netdev@...r.kernel.org>
CC:	nic_swsd <nic_swsd@...ltek.com>,
	"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
	"linux-usb@...r.kernel.org" <linux-usb@...r.kernel.org>
Subject: RE: [PATCH net-next 1/3] r8152: separate USB_RX_EARLY_AGG

 Sergei Shtylyov; netdev@...r.kernel.org
[...]
> > > +	ocp_data = tp->coalesce / 8;
> >
> >     Why not do it in the initializer?
>
> This is for patch #3. The patch #3 would use this function.
> The unit of the relative setting from the ethtool is 1 us.
> However, the unit for the hw is 8 us. Therefore, I save the
> value with the unit of 1 us, and transfer it to the unit of
> the hw when setting.

I think I misunderstand what you mean. I think you mean I
have to combine

	u32 ocp_data;
	ocp_data = tp->coalesce / 8;

into

	u32 ocp_data = tp->coalesce / 8;

I would correct it.

> > > +	ocp_write_word(tp, MCU_TYPE_USB, USB_RX_EARLY_TIMEOUT, ocp_data);
> > > +}
> > > +
> > > +static void r8153_set_rx_early_size(struct r8152 *tp)
> > > +{
> > > +	struct net_device *dev = tp->netdev;
> >
> >     Not sure you actually need this variable.
>
> If I replace dev->mtu with tp->netdev->mtu, the line would
> more than 80 characters. This is used to avoid it. Should
> I remove it?
>
> > > +	u32 ocp_data;
> > > +
> > > +	ocp_data = (agg_buf_sz - dev->mtu - VLAN_ETH_HLEN - VLAN_HLEN) / 4;
> >
> >     Why not in initializer?
>
> This is for patch #2. The patch #2 would use this function.
> It has to be re-calculated when the mtu is changed, or the
> function is called when the linking status changes to ON.

I think you mean I have to combine

	u32 ocp_data;
	ocp_data = (agg_buf_sz - dev->mtu - VLAN_ETH_HLEN - VLAN_HLEN) / 4;

into

	u32 ocp_data = (agg_buf_sz - dev->mtu - VLAN_ETH_HLEN - VLAN_HLEN) / 4;

I would correct it.

> > > +	ocp_write_word(tp, MCU_TYPE_USB, USB_RX_EARLY_SIZE, ocp_data);
> > >   }
> > [...]
> > > @@ -3911,6 +3907,13 @@ static int rtl8152_probe(struct
> > usb_interface *intf,
> > >   	tp->mii.reg_num_mask = 0x1f;
> > >   	tp->mii.phy_id = R8152_PHY_ID;
> > >
> > > +	if (udev->speed == USB_SPEED_SUPER)
> > > +		tp->coalesce = COALESCE_SUPER;
> > > +	else if (udev->speed == USB_SPEED_HIGH)
> > > +		tp->coalesce = COALESCE_HIGH;
> > > +	else
> > > +		tp->coalesce = COALESCE_SLOW;
> >
> >     This is asking to be a *switch* statement.
>
> Excuse me. I don't understand what you mean.
> The usb speed is determined when the device is plugged on
> the usb host controller or usb hub. The usb speed wouldn't
> chage unless you unplug the device and plug it to another
> port with different usb speed. Therefore, I provide different
> default values for different usb speed.

I think you mean

	switch (udev->speed) {
	case USB_SPEED_SUPER:
		...

I would correct it.
 
Best Regards,
Hayes
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html