| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1444997425-3396-12-git-send-email-jeffrey.t.kirsher@intel.com>
Date: Fri, 16 Oct 2015 05:10:19 -0700
From: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
To: davem@...emloft.net
Cc: Jesse Brandeburg <jesse.brandeburg@...el.com>,
netdev@...r.kernel.org, nhorman@...hat.com, sassmann@...hat.com,
jogreene@...hat.com, Jeff Kirsher <jeffrey.t.kirsher@...el.com>
Subject: [net-next v2 11/17] i40e/i40evf: moderate interrupts differently
From: Jesse Brandeburg <jesse.brandeburg@...el.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@...el.com>
Tested-by: Andrew Bowers <andrewx.bowers@...el.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
---
drivers/net/ethernet/intel/i40e/i40e.h | 1 +
drivers/net/ethernet/intel/i40e/i40e_ethtool.c | 24 ++++++++++++++++++++++++
drivers/net/ethernet/intel/i40e/i40e_main.c | 10 +++++++---
drivers/net/ethernet/intel/i40e/i40e_txrx.h | 10 ++++++++++
drivers/net/ethernet/intel/i40evf/i40e_txrx.h | 10 ++++++++++
5 files changed, 52 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/intel/i40e/i40e.h b/drivers/net/ethernet/intel/i40e/i40e.h
index 1125464..ad48f52 100644
--- a/drivers/net/ethernet/intel/i40e/i40e.h
+++ b/drivers/net/ethernet/intel/i40e/i40e.h
@@ -498,6 +498,7 @@ struct i40e_vsi {
*/
u16 rx_itr_setting;
u16 tx_itr_setting;
+ u16 int_rate_limit; /* value in usecs */
u16 rss_table_size;
u16 rss_size;
diff --git a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
index cb88e7a..1a50068 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_ethtool.c
@@ -1845,6 +1845,14 @@ static int i40e_get_coalesce(struct net_device *netdev,
ec->rx_coalesce_usecs = vsi->rx_itr_setting & ~I40E_ITR_DYNAMIC;
ec->tx_coalesce_usecs = vsi->tx_itr_setting & ~I40E_ITR_DYNAMIC;
+ /* we use the _usecs_high to store/set the interrupt rate limit
+ * that the hardware supports, that almost but not quite
+ * fits the original intent of the ethtool variable,
+ * the rx_coalesce_usecs_high limits total interrupts
+ * per second from both tx/rx sources.
+ */
+ ec->rx_coalesce_usecs_high = vsi->int_rate_limit;
+ ec->tx_coalesce_usecs_high = vsi->int_rate_limit;
return 0;
}
@@ -1863,6 +1871,17 @@ static int i40e_set_coalesce(struct net_device *netdev,
if (ec->tx_max_coalesced_frames_irq || ec->rx_max_coalesced_frames_irq)
vsi->work_limit = ec->tx_max_coalesced_frames_irq;
+ /* tx_coalesce_usecs_high is ignored, use rx-usecs-high instead */
+ if (ec->tx_coalesce_usecs_high != vsi->int_rate_limit) {
+ netif_info(pf, drv, netdev, "tx-usecs-high is not used, please program rx-usecs-high\n");
+ return -EINVAL;
+ }
+
+ if (ec->rx_coalesce_usecs_high >= INTRL_REG_TO_USEC(I40E_MAX_INTRL)) {
+ netif_info(pf, drv, netdev, "Invalid value, rx-usecs-high range is 0-235\n");
+ return -EINVAL;
+ }
+
vector = vsi->base_vector;
if ((ec->rx_coalesce_usecs >= (I40E_MIN_ITR << 1)) &&
(ec->rx_coalesce_usecs <= (I40E_MAX_ITR << 1))) {
@@ -1876,6 +1895,8 @@ static int i40e_set_coalesce(struct net_device *netdev,
return -EINVAL;
}
+ vsi->int_rate_limit = ec->rx_coalesce_usecs_high;
+
if ((ec->tx_coalesce_usecs >= (I40E_MIN_ITR << 1)) &&
(ec->tx_coalesce_usecs <= (I40E_MAX_ITR << 1))) {
vsi->tx_itr_setting = ec->tx_coalesce_usecs;
@@ -1900,11 +1921,14 @@ static int i40e_set_coalesce(struct net_device *netdev,
vsi->tx_itr_setting &= ~I40E_ITR_DYNAMIC;
for (i = 0; i < vsi->num_q_vectors; i++, vector++) {
+ u16 intrl = INTRL_USEC_TO_REG(vsi->int_rate_limit);
+
q_vector = vsi->q_vectors[i];
q_vector->rx.itr = ITR_TO_REG(vsi->rx_itr_setting);
wr32(hw, I40E_PFINT_ITRN(0, vector - 1), q_vector->rx.itr);
q_vector->tx.itr = ITR_TO_REG(vsi->tx_itr_setting);
wr32(hw, I40E_PFINT_ITRN(1, vector - 1), q_vector->tx.itr);
+ wr32(hw, I40E_PFINT_RATEN(vector - 1), intrl);
i40e_flush(hw);
}
diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c
index d731095..722b0a1 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_main.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_main.c
@@ -2901,11 +2901,9 @@ static int i40e_vsi_configure(struct i40e_vsi *vsi)
static void i40e_vsi_configure_msix(struct i40e_vsi *vsi)
{
struct i40e_pf *pf = vsi->back;
- struct i40e_q_vector *q_vector;
struct i40e_hw *hw = &pf->hw;
u16 vector;
int i, q;
- u32 val;
u32 qp;
/* The interrupt indexing is offset by 1 in the PFINT_ITRn
@@ -2915,7 +2913,8 @@ static void i40e_vsi_configure_msix(struct i40e_vsi *vsi)
qp = vsi->base_queue;
vector = vsi->base_vector;
for (i = 0; i < vsi->num_q_vectors; i++, vector++) {
- q_vector = vsi->q_vectors[i];
+ struct i40e_q_vector *q_vector = vsi->q_vectors[i];
+
q_vector->rx.itr = ITR_TO_REG(vsi->rx_itr_setting);
q_vector->rx.latency_range = I40E_LOW_LATENCY;
wr32(hw, I40E_PFINT_ITRN(I40E_RX_ITR, vector - 1),
@@ -2924,10 +2923,14 @@ static void i40e_vsi_configure_msix(struct i40e_vsi *vsi)
q_vector->tx.latency_range = I40E_LOW_LATENCY;
wr32(hw, I40E_PFINT_ITRN(I40E_TX_ITR, vector - 1),
q_vector->tx.itr);
+ wr32(hw, I40E_PFINT_RATEN(vector - 1),
+ INTRL_USEC_TO_REG(vsi->int_rate_limit));
/* Linked list for the queuepairs assigned to this vector */
wr32(hw, I40E_PFINT_LNKLSTN(vector - 1), qp);
for (q = 0; q < q_vector->num_ringpairs; q++) {
+ u32 val;
+
val = I40E_QINT_RQCTL_CAUSE_ENA_MASK |
(I40E_RX_ITR << I40E_QINT_RQCTL_ITR_INDX_SHIFT) |
(vector << I40E_QINT_RQCTL_MSIX_INDX_SHIFT) |
@@ -7040,6 +7043,7 @@ static int i40e_vsi_mem_alloc(struct i40e_pf *pf, enum i40e_vsi_type type)
vsi->idx = vsi_idx;
vsi->rx_itr_setting = pf->rx_itr_default;
vsi->tx_itr_setting = pf->tx_itr_default;
+ vsi->int_rate_limit = 0;
vsi->rss_table_size = (vsi->type == I40E_VSI_MAIN) ?
pf->rss_table_size : 64;
vsi->netdev_registered = false;
diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.h b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
index 75cecfa..7c0ed84 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_txrx.h
+++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.h
@@ -35,6 +35,7 @@
#define I40E_ITR_20K 0x0019
#define I40E_ITR_8K 0x003E
#define I40E_ITR_4K 0x007A
+#define I40E_MAX_INTRL 0x3B /* reg uses 4 usec resolution */
#define I40E_ITR_RX_DEF I40E_ITR_8K
#define I40E_ITR_TX_DEF I40E_ITR_4K
#define I40E_ITR_DYNAMIC 0x8000 /* use top bit as a flag */
@@ -44,6 +45,15 @@
#define ITR_TO_REG(setting) ((setting & ~I40E_ITR_DYNAMIC) >> 1)
#define ITR_IS_DYNAMIC(setting) (!!(setting & I40E_ITR_DYNAMIC))
#define ITR_REG_TO_USEC(itr_reg) (itr_reg << 1)
+/* 0x40 is the enable bit for interrupt rate limiting, and must be set if
+ * the value of the rate limit is non-zero
+ */
+#define INTRL_ENA BIT(6)
+#define INTRL_REG_TO_USEC(intrl) ((intrl & ~INTRL_ENA) << 2)
+#define INTRL_USEC_TO_REG(set) ((set) ? ((set) >> 2) | INTRL_ENA : 0)
+#define I40E_INTRL_8K 125 /* 8000 ints/sec */
+#define I40E_INTRL_62K 16 /* 62500 ints/sec */
+#define I40E_INTRL_83K 12 /* 83333 ints/sec */
#define I40E_QUEUE_END_OF_LIST 0x7FF
diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.h b/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
index 0c13ece..c4f5a4e 100644
--- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
+++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.h
@@ -35,6 +35,7 @@
#define I40E_ITR_20K 0x0019
#define I40E_ITR_8K 0x003E
#define I40E_ITR_4K 0x007A
+#define I40E_MAX_INTRL 0x3B /* reg uses 4 usec resolution */
#define I40E_ITR_RX_DEF I40E_ITR_8K
#define I40E_ITR_TX_DEF I40E_ITR_4K
#define I40E_ITR_DYNAMIC 0x8000 /* use top bit as a flag */
@@ -44,6 +45,15 @@
#define ITR_TO_REG(setting) ((setting & ~I40E_ITR_DYNAMIC) >> 1)
#define ITR_IS_DYNAMIC(setting) (!!(setting & I40E_ITR_DYNAMIC))
#define ITR_REG_TO_USEC(itr_reg) (itr_reg << 1)
+/* 0x40 is the enable bit for interrupt rate limiting, and must be set if
+ * the value of the rate limit is non-zero
+ */
+#define INTRL_ENA BIT(6)
+#define INTRL_REG_TO_USEC(intrl) ((intrl & ~INTRL_ENA) << 2)
+#define INTRL_USEC_TO_REG(set) ((set) ? ((set) >> 2) | INTRL_ENA : 0)
+#define I40E_INTRL_8K 125 /* 8000 ints/sec */
+#define I40E_INTRL_62K 16 /* 62500 ints/sec */
+#define I40E_INTRL_83K 12 /* 83333 ints/sec */
#define I40E_QUEUE_END_OF_LIST 0x7FF
--
2.4.3
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists