Message-Id: <1448496501-109561-1-git-send-email-jarno@ovn.org>
Date:	Wed, 25 Nov 2015 16:08:13 -0800
From:	Jarno Rajahalme <jarno@....org>
To:	netdev@...r.kernel.org
Cc:	netfilter-devel@...r.kernel.org, dev@...nvswitch.org, jarno@....org
Subject: [PATCH net-next v3 0/8] openvswitch: NAT support.

This series adds NAT support to openvswitch kernel module.  A few
changes are needed to the netfilter code to facilitate this (patches
1-3/8).  Patches 4-7 make the openvswitch kernel module ready for the
patch 8 that adds the NAT support by calling into netfilter NAT code
from the openvswitch conntrack action.

The OVS master now has the corresponding OVS userspace support to use
and test the NAT features.  Below if a walk through of a simple use
case.

In this case ports 1 and 2 are in different namespaces.  The OpenFlow
table below only allows IPv4 connections initiated from port 1, and
applies source NAT to those connections:

   in_port=1,ip,action=ct(commit,zone=1,nat(src=10.1.1.240-10.1.1.255)),2
   in_port=2,ct_state=-trk,ip,action=ct(table=0,zone=1,nat)
   in_port=2,ct_state=+est,ct_zone=1,ip,action=1

This flow table matches all IPv4 traffic from port 1, runs them
through conntrack in zone 1 and NATs them.  The NAT is initialized to
do source IP mapping to the given range for the first packet of each
connection, after which the new connection is committed (confirmed).
For further packets of already tracked connections NAT is done
according to the connection state and the commit is a no-op.  Each
packet that is not flagged as a drop by the CT action is forwarded to
port 2.  The CT action does an implicit fragmentation reassembly, so
that only complete packets are run through conntrack.  Reassembled
packets are re-fragmented on output.

The IPv4 traffic coming from port 2 is first matched for the
non-tracked state (-trk), which means that the packet has not been
through a CT action yet.  Such traffic is run trough the conntrack in
zone 1 and all packets associated with a NATted connection are NATted
also in the return direction.  After the packet has been through
conntrack it is recirculated back to OpenFlow table 0 (which is the
default table, so all the rules above are in table 0).  The CT action
changes the 'trk' flag to being set, so the packets after
recirculation no longer match the second rule.  The third rule then
matches the recirculated packets that were marked as established by
conntrack (+est), and the packet is output on port 1.  Matching on
ct_zone is not strictly needed, but in this test case it verifies that
the ct_zone key attribute is properly set by the conntrack action.

A full test case requires rules for ARP handling not shown here.

The flow table above is an OpenFlow table, and the rules therein
are translated to kernel flow entries on-demand by ovs-vswitchd.


Jarno Rajahalme (8):
  netfilter: Remove IP_CT_NEW_REPLY definition.
  netfilter: Factor out nf_ct_get_info().
  netfilter: Allow calling into nat helper without skb_dst.
  openvswitch: Update the CT state key only after nf_conntrack_in().
  openvswitch: Find existing conntrack entry after upcall.
  openvswitch: Handle NF_REPEAT in conntrack action.
  openvswitch: Delay conntrack helper call for new connections.
  openvswitch: Interface with NAT.

 include/net/netfilter/nf_conntrack.h               |  15 +
 include/uapi/linux/netfilter/nf_conntrack_common.h |  12 +-
 include/uapi/linux/openvswitch.h                   |  47 ++
 net/ipv4/netfilter/nf_nat_l3proto_ipv4.c           |  29 +-
 net/ipv6/netfilter/nf_nat_l3proto_ipv6.c           |  29 +-
 net/netfilter/nf_conntrack_core.c                  |  22 +-
 net/openvswitch/conntrack.c                        | 632 +++++++++++++++++++--
 net/openvswitch/conntrack.h                        |   3 +-
 8 files changed, 686 insertions(+), 103 deletions(-)

-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Powered by blists - more mailing lists