netdev - RE: [PATCH] can: rcar_canfd: Add Renesas R-Car CAN FD driver

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <SG2PR06MB1038AC389CDB35916408A5D6C3BC0@SG2PR06MB1038.apcprd06.prod.outlook.com>
Date:	Wed, 2 Mar 2016 08:41:40 +0000
From:	Ramesh Shanmugasundaram <ramesh.shanmugasundaram@...renesas.com>
To:	Marc Kleine-Budde <mkl@...gutronix.de>,
	"wg@...ndegger.com" <wg@...ndegger.com>,
	"robh+dt@...nel.org" <robh+dt@...nel.org>,
	"pawel.moll@....com" <pawel.moll@....com>,
	"mark.rutland@....com" <mark.rutland@....com>,
	"ijc+devicetree@...lion.org.uk" <ijc+devicetree@...lion.org.uk>,
	"galak@...eaurora.org" <galak@...eaurora.org>,
	"corbet@....net" <corbet@....net>
CC:	"linux-renesas-soc@...r.kernel.org" 
	<linux-renesas-soc@...r.kernel.org>,
	"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
	"linux-can@...r.kernel.org" <linux-can@...r.kernel.org>,
	"netdev@...r.kernel.org" <netdev@...r.kernel.org>,
	"linux-doc@...r.kernel.org" <linux-doc@...r.kernel.org>,
	"geert+renesas@...der.be" <geert+renesas@...der.be>,
	Chris Paterson <Chris.Paterson2@...esas.com>
Subject: RE: [PATCH] can: rcar_canfd: Add Renesas R-Car CAN FD driver

Hi Marc,

Thanks for the review.

> On 03/01/2016 10:34 AM, Ramesh Shanmugasundaram wrote:
> > This patch adds support for the CAN FD controller found in Renesas
> > R-Car SoCs. The controller operates in CAN FD mode by default. Two
> > test modes are available and can be enabled by the
> > "rcar_canfd.testmode" module parameter. Refer to Documentation/kernel-
> parameters.txt.
> 
> Is the channel loopback mode configurable per channel? If so, please
> remove the module parameter and make use of CAN_CTRLMODE_LOOPBACK to
> configure it.

The loopback setting is not truly a per channel attribute. It requires touching Rx rules which can be done only when the controller's global state is reset (during probe). CAN_CTRLMODE_LOOPBACK config option is possible only through .ndo_open of that channel but the global controller state needs to be operational by this time. As it is a global attribute & for the above reason, I choose the module option.

> 
> > CAN FD mode supports both Classical CAN & CAN FD frame formats. The
> > controller supports ISO 11898-1:2015 CAN FD format only.
> >
> > This controller supports two channels and the driver can enable either
> > or both of the channels.
> >
> > Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs
> > (one per channel) for transmission. Rx filter rules are configured to
> > the minimum (one per channel) and it accepts Standard, Extended, Data
> > & Remote Frame combinations.
> 
> I see no locking for the tx-path.
 
I am not sure why locking is needed in tx-path? 
However, looking at it again, I should move the incrementing of head after the "sts" handing to be apt. What do you think?

Thanks,
Ramesh