netdev - Re: am335x: no multicast reception over VLAN

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <56FA78AA.4030402@ti.com>
Date:	Tue, 29 Mar 2016 15:44:26 +0300
From:	Grygorii Strashko <grygorii.strashko@...com>
To:	Yegor Yefremov <yegorslists@...glemail.com>
CC:	Mugunthan V N <mugunthanvnm@...com>,
	netdev <netdev@...r.kernel.org>,
	"linux-omap@...r.kernel.org" <linux-omap@...r.kernel.org>,
	<drivshin@...worx.com>, <ml@...kusgrimm.de>
Subject: Re: am335x: no multicast reception over VLAN

On 03/29/2016 03:35 PM, Yegor Yefremov wrote:
> On Tue, Mar 29, 2016 at 1:05 PM, Grygorii Strashko
> <grygorii.strashko@...com> wrote:
>> On 03/29/2016 08:21 AM, Yegor Yefremov wrote:
>>> Hi Mugunthan,
>>>
>>> On Tue, Mar 29, 2016 at 6:00 AM, Mugunthan V N <mugunthanvnm@...com> wrote:
>>>> Hi Yegor
>>>>
>>>> On Wednesday 16 March 2016 08:35 PM, Yegor Yefremov wrote:
>>>>> I have an am335x based board using CPSW in Dual EMAC mode. Without
>>>>> VLAN IDs I can receive and send multicast packets [1]. When I create
>>>>> VLAN ID:
>>>>>
>>>>> ip link add link eth1 name eth1.100 type vlan id 100
>>>>> ip addr add 192.168.100.2/24 brd 192.168.100.255 dev eth1.100
>>>>> route add -net 224.0.0.0 netmask 224.0.0.0 eth1.100
>>>>>
>>>>> I can successfully send multicast packets, but not receive them. On
>>>>> the other side of the Ethernet cable I've used Pandaboard. Pandaboard
>>>>> could both receive and send multicast packets via VLAN.
>>>>
>>>> Are you trying multicast tx/rx on eth1 or eth1.100?
>>>
>>> I'm trying multicast tx/rx on eth1.100.
>>>
>>> eth1 has no problems.
>>>
>>
>> it'd be nice if will be able to post here output fom commands:
>> # switch-config -d [git://git.ti.com/switch-config/switch-config.git v4.1]
>> # ifconfig -a
>> # tcpdump -e -f -Q in -i eth0
>> # tcpdump -e -f -Q in -i eth0.100
> 
> Which kernel/branch do you want me to test?
> 
> git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git and ti-rt-linux-4.1.y?
> 
> So far I was using vanilla kernel.

Your branch (but better 4.5 kernels (or 4.4)). 
Just when you've done with configuration run cmds 1&2,
and when you run your use-case - run cmds 2&3 on receiver side (grap ~5-10 packets).
then stop test and run cmd 1 again.

After all could you provide your console output here, pls.


-- 
regards,
-grygorii