lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <57612649.40907@hisilicon.com>
Date:	Wed, 15 Jun 2016 17:56:25 +0800
From:	Dongpo Li <lidongpo@...ilicon.com>
To:	Arnd Bergmann <arnd@...db.de>
CC:	<f.fainelli@...il.com>, <robh+dt@...nel.org>,
	<mark.rutland@....com>, <davem@...emloft.net>,
	<xuejiancheng@...ilicon.com>, <netdev@...r.kernel.org>,
	<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH 3/3] net: hisilicon: Add Fast Ethernet MAC driver



On 2016/6/15 5:20, Arnd Bergmann wrote:
> On Tuesday, June 14, 2016 9:17:44 PM CEST Li Dongpo wrote:
>> On 2016/6/13 17:06, Arnd Bergmann wrote:
>>> On Monday, June 13, 2016 2:07:56 PM CEST Dongpo Li wrote:
>>> You tx function uses BQL to optimize the queue length, and that
>>> is great. You also check xmit reclaim for rx interrupts, so
>>> as long as you have both rx and tx traffic, this should work
>>> great.
>>>
>>> However, I notice that you only have a 'tx fifo empty'
>>> interrupt triggering the napi poll, so I guess on a tx-only
>>> workload you will always end up pushing packets into the
>>> queue until BQL throttles tx, and then get the interrupt
>>> after all packets have been sent, which will cause BQL to
>>> make the queue longer up to the maximum queue size, and that
>>> negates the effect of BQL.
>>>
>>> Is there any way you can get a tx interrupt earlier than
>>> this in order to get a more balanced queue, or is it ok
>>> to just rely on rx packets to come in occasionally, and
>>> just use the tx fifo empty interrupt as a fallback?
>>>
>> In tx direction, there are only two kinds of interrupts, 'tx fifo empty'
>> and 'tx one packet finish'. I didn't use 'tx one packet finish' because
>> it would lead to high hardware interrupts rate. This has been verified in
>> our chips. It's ok to just use tx fifo empty interrupt.
> 
> I'm not convinced by the explanation, I don't think that has anything
> to do with the hardware design, but instead is about the correctness
> of the BQL logic with your driver.
> 
> Maybe your xmit function can do something like
> 
> 	if (dql_avail(netdev_get_tx_queue(dev, 0)->dql) < 0)
> 		enable per-packet interrupt
> 	else
> 		use only fifo-empty interrupt
> 
> That way, you don't get a lot of interrupts when the system is
> in a state of packets being received and sent continuously,
> but if you get to the point where your tx queue fills up
> and no rx interrupts arrive, you don't have to wait for it
> to become completely empty before adding new packets, and
> BQL won't keep growing the queue.
> 
Hi Arnd,
Thanks for your advice. It's a good advice and I will try to fix it and
test on our chip.

>>>> +    priv->phy_mode = of_get_phy_mode(node);
>>>> +    if (priv->phy_mode < 0) {
>>>> +            dev_err(dev, "not find phy-mode\n");
>>>> +            ret = -EINVAL;
>>>> +            goto out_disable_clk;
>>>> +    }
>>>> +
>>>> +    priv->phy_node = of_parse_phandle(node, "phy-handle", 0);
>>>> +    if (!priv->phy_node) {
>>>> +            dev_err(dev, "not find phy-handle\n");
>>>> +            ret = -EINVAL;
>>>> +            goto out_disable_clk;
>>>> +    }
>>>> +
>>>> +    priv->phy = of_phy_connect(ndev, priv->phy_node,
>>>> +                               hisi_femac_adjust_link, 0, priv->phy_mode);
>>>> +    if (!(priv->phy) || IS_ERR(priv->phy)) {
>>>> +            dev_err(dev, "connect to PHY failed!\n");
>>>> +            ret = -ENODEV;
>>>> +            goto out_phy_node;
>>>> +    }
>>>
>>> I wonder if we could generalize this set of three calls, I
>>> get the impression that we duplicate this across several
>>> drivers that shouldn't need to bother with the specific
>>> phy-handle and phy-mode properties.
>>>
>> Some drivers only call 'of_phy_connect' when ndo_open called,
>> some call when driver probed. But 'phy_mode' and 'phy_node' are
>> usually initialized when driver probed.
>> So I think it's not suitable to combine 'of_phy_connect' with
>> 'of_get_phy_mode' and 'of_parse_phandle'.
>> Do you have any more suggestions ?
> 
> My idea was to add another interface that drivers could optionally
> call if they use the logic that you have here, but other drivers
> could keep using the plain of_phy_connect.
> 
> Anyway, this was just an idea, it's not important.
> 
ok, I get your point. I will try to figure out the general interface.
If there is a solution, I'd like to get more review.
> 	Arnd
> 
> .
> 

    Regards,
    Dongpo

.

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ