[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <b1afa44f-7c41-c9bc-bb0f-9ccced25a0ef@collabora.com>
Date: Wed, 31 Aug 2016 13:28:34 -0400
From: Robert Foss <robert.foss@...labora.com>
To: freddy@...x.com.tw, Dean_Jenkins@...tor.com,
Mark_Craske@...tor.com, davem@...emloft.net, ivecera@...hat.com,
john.stultz@...aro.org, vpalatin@...omium.org,
stephen@...workplumber.org, grundler@...omium.org,
changchias@...il.com, allan@...x.com.tw, andrew@...n.ch,
tremyfr@...il.com, colin.king@...onical.com,
linux-usb@...r.kernel.org, netdev@...r.kernel.org,
linux-kernel@...r.kernel.org, vpalatin@...gle.com
Subject: Re: [PATCH v3 0/5] net/usb: asix driver improvements
Additional testing has been done the hardware that is available to me.
I'm not seeing any dmesg warnings/errors that are new to this series:
AX88772A
- Pass network_EthernetStressPlug
- Pass phy up/down + iperf3 UDP stress
- Pass network_EthernetStressPlug + iperf3 UDP stress
AX88772B
- Pass network_EthernetStressPlug
- Pass phy up/down + iperf3 UDP stress
- Pass network_EthernetStressPlug + iperf3 UDP stress
Cisco AX88772 A(?)
- Pass network_EthernetStressPlug
- Pass phy up/down + iperf3 UDP stress
- Pass network_EthernetStressPlug + iperf3 UDP stress
Cisco AX88772 B(?)
- Pass network_EthernetStressPlug
- Pass phy up/down + iperf3 UDP stress
- Pass network_EthernetStressPlug + iperf3 UDP stress
AX88178
- Pass network_EthernetStressPlug
- Pass phy up/down + iperf3 UDP stress
- Pass network_EthernetStressPlug + iperf3 UDP stress
AX88179
- Pass network_EthernetStressPlug
- Pass phy up/down + iperf3 UDP stress?
-- [ 8794.555902] ax88179_178a 1-1.3:1.0 eth1: kevent 4 may have been
dropped
- Pass network_EthernetStressPlug + iperf3 UDP stresss
I also saw some sporadic header checksum errors.
But those too are seen on upstream/master.
asix_rx_fixup() Bad Header Length 0x98a993c8, offset 4
Test details:
network_EthernetStressPlug:
http://memcpy.io/ethernet-device-stress-testing.html
phy up/down:
for i in
{1..10}
do
sudo ifdown eth1
if sudo ifup eth1; then
echo "Command success"
else
echo "Command failed"
fi
done
iperf3 UDP:
sudo iperf3 -c 192.168.0.28 -u -b 100M -t 0
On 2016-08-29 09:32 AM, robert.foss@...labora.com wrote:
> From: Robert Foss <robert.foss@...labora.com>
>
> This is a resubmission of v3, since the netdev
> mailinlist was not sent the previous submission.
>
> This series improves power management of the asix driver.
>
> - Suspend/resume support is improved to save needed registers.
> - Device disconnection is improved.
> - Fixes AX88772x resume failures
> - Implementes IEEE 802.3 spec section "22.2.4.1.1 Reset" correctly
> - Fixes AX_CMD_WRITE_MEDIUM_MODE being set incorrectly
>
> Changes since v1:
> - Added proper metadata tags to series.
> - Added two more patches to series.
>
> Changes since v2:
> - Added coverletter
> - Tested patches on AX88772A/AX88772B/AX88178/AX88179 hardware
>
> Allan Chou (1):
> net: asix: Fix AX88772x resume failures
>
> Freddy Xin (1):
> net: asix: Add in_pm parameter
>
> Grant Grundler (2):
> net: asix: see 802.3 spec for phy reset
> net: asix: autoneg will set WRITE_MEDIUM reg
>
> Vincent Palatin (1):
> net: asix: Avoid looping when the device is disconnected
>
> drivers/net/usb/asix.h | 40 ++-
> drivers/net/usb/asix_common.c | 212 ++++++++++++----
> drivers/net/usb/asix_devices.c | 450 +++++++++++++++++++++++++++-------
> drivers/net/usb/ax88172a.c | 29 +-
> 4 files changed, 575 insertions(+), 156 deletions(-)
>
Powered by blists - more mailing lists