| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20170414090752.GA1992@nanopsycho>
Date: Fri, 14 Apr 2017 11:07:52 +0200
From: Jiri Pirko <jiri@...nulli.us>
To: Subash Abhinov Kasiviswanathan <subashab@...eaurora.org>
Cc: netdev@...r.kernel.org, davem@...emloft.net,
fengguang.wu@...el.com, dcbw@...hat.com
Subject: Re: [PATCH net-next 1/1 v3] drivers: net: rmnet: Initial
implementation
Fri, Apr 14, 2017 at 07:05:29AM CEST, subashab@...eaurora.org wrote:
>RmNet driver provides a transport agnostic MAP (multiplexing and
>aggregation protocol) support in embedded module. Module provides
>virtual network devices which can be attached to any IP-mode
>physical device. This will be used to provide all MAP functionality
>on future hardware in a single consistent location.
>
>Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@...eaurora.org>
>---
> Documentation/networking/rmnet.txt | 83 +++++
> drivers/net/Kconfig | 2 +
> drivers/net/Makefile | 1 +
> drivers/net/rmnet/Kconfig | 23 ++
> drivers/net/rmnet/Makefile | 14 +
> drivers/net/rmnet/rmnet_config.c | 592 ++++++++++++++++++++++++++++++++++
> drivers/net/rmnet/rmnet_config.h | 79 +++++
> drivers/net/rmnet/rmnet_handlers.c | 517 +++++++++++++++++++++++++++++
> drivers/net/rmnet/rmnet_handlers.h | 24 ++
> drivers/net/rmnet/rmnet_main.c | 52 +++
> drivers/net/rmnet/rmnet_map.h | 100 ++++++
> drivers/net/rmnet/rmnet_map_command.c | 180 +++++++++++
> drivers/net/rmnet/rmnet_map_data.c | 145 +++++++++
> drivers/net/rmnet/rmnet_private.h | 76 +++++
> drivers/net/rmnet/rmnet_stats.c | 86 +++++
> drivers/net/rmnet/rmnet_stats.h | 61 ++++
> drivers/net/rmnet/rmnet_vnd.c | 353 ++++++++++++++++++++
> drivers/net/rmnet/rmnet_vnd.h | 34 ++
> include/uapi/linux/Kbuild | 1 +
> include/uapi/linux/if_arp.h | 1 +
> include/uapi/linux/if_ether.h | 4 +-
> include/uapi/linux/rmnet.h | 34 ++
> 22 files changed, 2461 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/networking/rmnet.txt
> create mode 100644 drivers/net/rmnet/Kconfig
> create mode 100644 drivers/net/rmnet/Makefile
> create mode 100644 drivers/net/rmnet/rmnet_config.c
> create mode 100644 drivers/net/rmnet/rmnet_config.h
> create mode 100644 drivers/net/rmnet/rmnet_handlers.c
> create mode 100644 drivers/net/rmnet/rmnet_handlers.h
> create mode 100644 drivers/net/rmnet/rmnet_main.c
> create mode 100644 drivers/net/rmnet/rmnet_map.h
> create mode 100644 drivers/net/rmnet/rmnet_map_command.c
> create mode 100644 drivers/net/rmnet/rmnet_map_data.c
> create mode 100644 drivers/net/rmnet/rmnet_private.h
> create mode 100644 drivers/net/rmnet/rmnet_stats.c
> create mode 100644 drivers/net/rmnet/rmnet_stats.h
> create mode 100644 drivers/net/rmnet/rmnet_vnd.c
> create mode 100644 drivers/net/rmnet/rmnet_vnd.h
> create mode 100644 include/uapi/linux/rmnet.h
>
>diff --git a/Documentation/networking/rmnet.txt b/Documentation/networking/rmnet.txt
>new file mode 100644
>index 0000000..58d3ea2
>--- /dev/null
>+++ b/Documentation/networking/rmnet.txt
>@@ -0,0 +1,83 @@
>+1. Introduction
>+
>+rmnet driver is used for supporting the Multiplexing and aggregation
>+Protocol (MAP). This protocol is used by all recent chipsets using Qualcomm
>+Technologies, Inc. modems.
>+
>+This driver can be used to register onto any physical network device in
>+IP mode. Physical transports include USB, HSIC, PCIe and IP accelerator.
>+
>+Multiplexing allows for creation of logical netdevices (rmnet devices) to
>+handle multiple private data networks (PDN) like a default internet, tethering,
>+multimedia messaging service (MMS) or IP media subsystem (IMS). Hardware sends
>+packets with MAP headers to rmnet. Based on the multiplexer id, rmnet
>+routes to the appropriate PDN after removing the MAP header.
>+
>+Aggregation is required to achieve high data rates. This involves hardware
>+sending aggregated bunch of MAP frames. rmnet driver will de-aggregate
>+these MAP frames and send them to appropriate PDN's.
>+
>+2. Packet format
>+
>+a. MAP packet (data / control)
>+
>+MAP header has the same endianness of the IP packet.
>+
>+Packet format -
>+
>+Bit 0 1 2-7 8 - 15 16 - 31
>+Function Command / Data Reserved Pad Multiplexer ID Payload length
>+Bit 32 - x
>+Function Raw Bytes
>+
>+Command (1)/ Data (0) bit value is to indicate if the packet is a MAP command
>+or data packet. Control packet is used for transport level flow control. Data
>+packets are standard IP packets.
>+
>+Reserved bits are usually zeroed out and to be ignored by receiver.
>+
>+Padding is number of bytes to be added for 4 byte alignment if required by
>+hardware.
>+
>+Multiplexer ID is to indicate the PDN on which data has to be sent.
>+
>+Payload length includes the padding length but does not include MAP header
>+length.
>+
>+b. MAP packet (command specific)
>+
>+Bit 0 1 2-7 8 - 15 16 - 31
>+Function Command Reserved Pad Multiplexer ID Payload length
>+Bit 32 - 39 40 - 45 46 - 47 48 - 63
>+Function Command name Reserved Command Type Reserved
>+Bit 64 - 95
>+Function Transaction ID
>+Bit 96 - 127
>+Function Command data
>+
>+Command 1 indicates disabling flow while 2 is enabling flow
>+
>+Command types -
>+0 for MAP command request
>+1 is to acknowledge the receipt of a command
>+2 is for unsupported commands
>+3 is for error during processing of commands
>+
>+c. Aggregation
>+
>+Aggregation is multiple MAP packets (can be data or command) delivered to
>+rmnet in a single linear skb. rmnet will process the individual
>+packets and either ACK the MAP command or deliver the IP packet to the
>+network stack as needed
>+
>+MAP header|IP Packet|Optional padding|MAP header|IP Packet|Optional padding....
>+MAP header|IP Packet|Optional padding|MAP header|Command Packet|Optional pad...
>+
>+3. Userspace configuration
>+
>+rmnet userspace configuration is done through netlink library librmnetctl
>+and command line utility rmnetcli. Utility is hosted in codeaurora forum git.
>+The driver uses rtnl_link_ops for communication.
>+
>+https://source.codeaurora.org/quic/la/platform/vendor/qcom-opensource/\
>+dataservices/tree/rmnetctl
>diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
>index 100fbdc..c4ccd6d 100644
>--- a/drivers/net/Kconfig
>+++ b/drivers/net/Kconfig
>@@ -477,4 +477,6 @@ config FUJITSU_ES
>
> source "drivers/net/hyperv/Kconfig"
>
>+source "drivers/net/rmnet/Kconfig"
>+
> endif # NETDEVICES
>diff --git a/drivers/net/Makefile b/drivers/net/Makefile
>index 98ed4d9..29b3945 100644
>--- a/drivers/net/Makefile
>+++ b/drivers/net/Makefile
>@@ -74,3 +74,4 @@ obj-$(CONFIG_HYPERV_NET) += hyperv/
> obj-$(CONFIG_NTB_NETDEV) += ntb_netdev.o
>
> obj-$(CONFIG_FUJITSU_ES) += fjes/
>+obj-$(CONFIG_RMNET) += rmnet/
>diff --git a/drivers/net/rmnet/Kconfig b/drivers/net/rmnet/Kconfig
>new file mode 100644
>index 0000000..63cd477
>--- /dev/null
>+++ b/drivers/net/rmnet/Kconfig
>@@ -0,0 +1,23 @@
>+#
>+# RMNET MAP driver
>+#
>+
>+menuconfig RMNET
>+ depends on NETDEVICES
>+ bool "RmNet MAP driver"
>+ default n
>+ ---help---
>+ If you say Y here, then the rmnet module will be statically
>+ compiled into the kernel. The rmnet module provides MAP
>+ functionality for embedded and bridged traffic.
>+if RMNET
>+
>+config RMNET_DEBUG
>+ bool "RmNet Debug Logging"
No, please use standard facilities in order to do debug logging.
>+ default n
>+ ---help---
>+ Say Y here if you want RmNet to be able to log packets in main
>+ system log. This should not be enabled on production builds as it can
>+ impact system performance. Note that simply enabling it here will not
>+ enable the logging; it must be enabled at run-time as well.
>+endif # RMNET
>diff --git a/drivers/net/rmnet/Makefile b/drivers/net/rmnet/Makefile
>new file mode 100644
>index 0000000..2b6c9cf
>--- /dev/null
>+++ b/drivers/net/rmnet/Makefile
>@@ -0,0 +1,14 @@
>+#
>+# Makefile for the RMNET module
>+#
>+
>+rmnet-y := rmnet_main.o
>+rmnet-y += rmnet_config.o
>+rmnet-y += rmnet_vnd.o
>+rmnet-y += rmnet_handlers.o
>+rmnet-y += rmnet_map_data.o
>+rmnet-y += rmnet_map_command.o
>+rmnet-y += rmnet_stats.o
>+obj-$(CONFIG_RMNET) += rmnet.o
>+
>+CFLAGS_rmnet_main.o := -I$(src)
>diff --git a/drivers/net/rmnet/rmnet_config.c b/drivers/net/rmnet/rmnet_config.c
>new file mode 100644
>index 0000000..a4bc76b
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_config.c
>@@ -0,0 +1,592 @@
>+/* Copyright (c) 2013-2017, The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ * RMNET configuration engine
>+ *
>+ */
>+
>+#include <net/sock.h>
>+#include <linux/module.h>
>+#include <linux/netlink.h>
>+#include <linux/netdevice.h>
>+#include <linux/skbuff.h>
>+#include <linux/spinlock.h>
>+#include <linux/rmnet.h>
>+#include "rmnet_config.h"
>+#include "rmnet_handlers.h"
>+#include "rmnet_vnd.h"
>+#include "rmnet_private.h"
>+
>+RMNET_LOG_MODULE(RMNET_LOGMASK_CONFIG);
>+
>+/* Local Definitions and Declarations */
>+#define RMNET_LOCAL_LOGICAL_ENDPOINT -1
>+
>+/* _rmnet_is_physical_endpoint_associated() - Determines if device is associated
>+ * @dev: Device to get check
>+ *
>+ * Compares device rx_handler callback pointer against known function
>+ */
>+static inline int _rmnet_is_physical_endpoint_associated(struct net_device *dev)
>+{
>+ rx_handler_func_t *rx_handler;
>+
>+ rx_handler = rcu_dereference(dev->rx_handler);
>+
>+ if (rx_handler == rmnet_rx_handler)
>+ return 1;
=>+ else
>+ return 0;
>+}
>+
>+/* _rmnet_get_phys_ep_config() - Get physical ep config for an associated device
>+ * @dev: Device to get endpoint configuration from
>+ */
>+static inline struct rmnet_phys_ep_conf_s *_rmnet_get_phys_ep_config
>+ (struct net_device *dev)
>+{
>+ if (_rmnet_is_physical_endpoint_associated(dev))
>+ return (struct rmnet_phys_ep_conf_s *)
>+ rcu_dereference(dev->rx_handler_data);
>+ else
>+ return 0;
>+}
>+
>+struct rmnet_free_vnd_work {
>+ struct work_struct work;
>+ int vnd_id[RMNET_MAX_VND];
>+ int count;
>+};
>+
>+/* _rmnet_get_logical_ep() - Gets the logical end point configuration
>+ * structure for a network device
>+ * @dev: Device to get endpoint configuration from
>+ * @config_id: Logical endpoint id on device
>+ * Retrieves the logical_endpoint_config structure.
>+ */
>+static struct rmnet_logical_ep_conf_s *_rmnet_get_logical_ep
Dont use "_" at the start of a name without purpose
>+ (struct net_device *dev, int config_id)
>+{
>+ struct rmnet_phys_ep_conf_s *config;
>+ struct rmnet_logical_ep_conf_s *epconfig_l;
>+
>+ if (rmnet_vnd_is_vnd(dev)) {
>+ epconfig_l = rmnet_vnd_get_le_config(dev);
>+ } else {
>+ config = _rmnet_get_phys_ep_config(dev);
>+
>+ if (!config)
>+ return NULL;
>+
>+ if (config_id == RMNET_LOCAL_LOGICAL_ENDPOINT)
>+ epconfig_l = &config->local_ep;
>+ else
>+ epconfig_l = &config->muxed_ep[config_id];
>+ }
>+
>+ return epconfig_l;
>+}
>+
>+/* rmnet_unassociate_network_device() - Unassociate network device
>+ * @dev: Device to unassociate
>+ *
>+ * Frees all structures generate for device. Unregisters rx_handler
>+ */
>+static int rmnet_unassociate_network_device(struct net_device *dev)
>+{
>+ struct rmnet_phys_ep_conf_s *config;
>+ int config_id = RMNET_LOCAL_LOGICAL_ENDPOINT;
>+ struct rmnet_logical_ep_conf_s *epconfig_l;
>+
>+ ASSERT_RTNL();
>+
>+ LOGL("(%s);", dev->name);
>+
>+ if (!dev || !_rmnet_is_physical_endpoint_associated(dev))
>+ return -EINVAL;
>+
>+ for (; config_id < RMNET_MAX_LOGICAL_EP; config_id++) {
>+ epconfig_l = _rmnet_get_logical_ep(dev, config_id);
>+ if (epconfig_l && epconfig_l->refcount)
>+ return -EINVAL;
>+ }
>+
>+ config = (struct rmnet_phys_ep_conf_s *)
>+ rcu_dereference(dev->rx_handler_data);
>+
>+ if (!config)
>+ return -EINVAL;
>+
>+ kfree(config);
>+
>+ netdev_rx_handler_unregister(dev);
>+
>+ dev_put(dev);
>+ return 0;
>+}
>+
>+/* rmnet_set_ingress_data_format() - Set ingress data format on network device
>+ * @dev: Device to ingress data format on
>+ * @egress_data_format: 32-bit unsigned bitmask of ingress format
>+ *
>+ * Network device must already have association with RmNet Data driver
>+ */
>+static int rmnet_set_ingress_data_format(struct net_device *dev,
>+ u32 ingress_data_format)
>+{
>+ struct rmnet_phys_ep_conf_s *config;
>+
>+ ASSERT_RTNL();
>+
>+ LOGL("(%s,0x%08X);", dev->name, ingress_data_format);
>+
>+ if (!dev)
>+ return -EINVAL;
>+
>+ config = _rmnet_get_phys_ep_config(dev);
>+ if (!config)
>+ return -EINVAL;
>+
>+ config->ingress_data_format = ingress_data_format;
>+
>+ return 0;
>+}
>+
>+/* rmnet_set_egress_data_format() - Set egress data format on network device
>+ * @dev: Device to egress data format on
>+ * @egress_data_format: 32-bit unsigned bitmask of egress format
>+ *
>+ * Network device must already have association with RmNet Data driver
>+ */
>+static int rmnet_set_egress_data_format(struct net_device *dev,
>+ u32 egress_data_format,
>+ u16 agg_size,
>+ u16 agg_count)
>+{
>+ struct rmnet_phys_ep_conf_s *config;
>+
>+ ASSERT_RTNL();
>+
>+ LOGL("(%s,0x%08X, %d, %d);",
>+ dev->name, egress_data_format, agg_size, agg_count);
>+
>+ if (!dev)
>+ return -EINVAL;
>+
>+ config = _rmnet_get_phys_ep_config(dev);
>+ if (!config)
>+ return -EINVAL;
>+
>+ config->egress_data_format = egress_data_format;
>+
>+ return 0;
>+}
>+
>+/* rmnet_associate_network_device() - Associate network device
>+ * @dev: Device to register with RmNet data
>+ *
>+ * Typically used on physical network devices. Registers RX handler and private
>+ * metadata structures.
>+ */
>+static int rmnet_associate_network_device(struct net_device *dev)
I would expect to see here you making connection between real_dev and
rmnet dev. I don't see such thing. Name of the function is misleading.
>+{
>+ struct rmnet_phys_ep_conf_s *config;
>+ int rc;
>+
>+ ASSERT_RTNL();
>+
>+ LOGL("(%s);\n", dev->name);
>+
>+ if (!dev || _rmnet_is_physical_endpoint_associated(dev) ||
>+ rmnet_vnd_is_vnd(dev)) {
>+ LOGM("cannot register with this dev");
>+ return -EINVAL;
>+ }
>+
>+ config = kmalloc(sizeof(*config), GFP_ATOMIC);
kzalloc, and you don't have to zero the memory.
>+ if (!config)
>+ return -ENOMEM;
>+
>+ memset(config, 0, sizeof(struct rmnet_phys_ep_conf_s));
>+ config->dev = dev;
>+
>+ rc = netdev_rx_handler_register(dev, rmnet_rx_handler, config);
>+
>+ if (rc) {
>+ LOGM("netdev_rx_handler_register returns %d", rc);
>+ kfree(config);
>+ return -EBUSY;
>+ }
>+
>+ dev_hold(dev);
>+ return 0;
>+}
>+
>+/* __rmnet_set_logical_endpoint_config() - Set logical endpoing config on device
>+ * @dev: Device to set endpoint configuration on
>+ * @config_id: logical endpoint id on device
>+ * @epconfig: endpoint configuration structure to set
>+ */
>+static int __rmnet_set_logical_endpoint_config
>+ (struct net_device *dev,
>+ int config_id,
>+ struct rmnet_logical_ep_conf_s *epconfig)
>+{
>+ struct rmnet_logical_ep_conf_s *epconfig_l;
>+
>+ ASSERT_RTNL();
>+
>+ if (!dev || config_id < RMNET_LOCAL_LOGICAL_ENDPOINT ||
>+ config_id >= RMNET_MAX_LOGICAL_EP)
>+ return -EINVAL;
>+
>+ epconfig_l = _rmnet_get_logical_ep(dev, config_id);
>+
>+ if (!epconfig_l || epconfig_l->refcount)
>+ return -EINVAL;
>+
>+ memcpy(epconfig_l, epconfig, sizeof(struct rmnet_logical_ep_conf_s));
>+ if (config_id == RMNET_LOCAL_LOGICAL_ENDPOINT)
>+ epconfig_l->mux_id = 0;
>+ else
>+ epconfig_l->mux_id = config_id;
>+
>+ /* Explicitly hold a reference to the egress device */
>+ dev_hold(epconfig_l->egress_dev);
>+ return 0;
>+}
>+
>+/* _rmnet_unset_logical_endpoint_config() - Un-set the logical endpoing config
>+ * on device
>+ * @dev: Device to set endpoint configuration on
>+ * @config_id: logical endpoint id on device
>+ */
>+static int _rmnet_unset_logical_endpoint_config(struct net_device *dev,
>+ int config_id)
>+{
>+ struct rmnet_logical_ep_conf_s *epconfig_l = 0;
>+
>+ ASSERT_RTNL();
>+
>+ if (!dev || config_id < RMNET_LOCAL_LOGICAL_ENDPOINT ||
>+ config_id >= RMNET_MAX_LOGICAL_EP)
>+ return -EINVAL;
>+
>+ epconfig_l = _rmnet_get_logical_ep(dev, config_id);
>+
>+ if (!epconfig_l || !epconfig_l->refcount)
>+ return -EINVAL;
>+
>+ /* Explicitly release the reference from the egress device */
>+ dev_put(epconfig_l->egress_dev);
>+ memset(epconfig_l, 0, sizeof(struct rmnet_logical_ep_conf_s));
>+
>+ return 0;
>+}
>+
>+/* rmnet_set_logical_endpoint_config() - Set logical endpoint config on a device
>+ * @dev: Device to set endpoint configuration on
>+ * @config_id: logical endpoint id on device
>+ * @rmnet_mode: endpoint mode. Values from: rmnet_config_endpoint_modes_e
>+ * @egress_device: device node to forward packet to once done processing in
>+ * ingress/egress handlers
>+ *
>+ * Creates a logical_endpoint_config structure and fills in the information from
>+ * function arguments. Calls __rmnet_set_logical_endpoint_config() to finish
>+ * configuration. Network device must already have association with RmNet Data
>+ * driver
>+ */
>+static int rmnet_set_logical_endpoint_config(struct net_device *dev,
>+ int config_id,
>+ u8 rmnet_mode,
>+ struct net_device *egress_dev)
>+{
>+ struct rmnet_logical_ep_conf_s epconfig;
>+
>+ LOGL("(%s, %d, %d, %s);",
>+ dev->name, config_id, rmnet_mode, egress_dev->name);
>+
>+ if (!egress_dev ||
>+ ((!_rmnet_is_physical_endpoint_associated(egress_dev)) &&
>+ (!rmnet_vnd_is_vnd(egress_dev)))) {
>+ return -EINVAL;
>+ }
>+
>+ memset(&epconfig, 0, sizeof(struct rmnet_logical_ep_conf_s));
>+ epconfig.refcount = 1;
>+ epconfig.rmnet_mode = rmnet_mode;
>+ epconfig.egress_dev = egress_dev;
>+
>+ return __rmnet_set_logical_endpoint_config(dev, config_id, &epconfig);
>+}
>+
>+/* rmnet_unset_logical_endpoint_config() - Un-set logical endpoing configuration
>+ * on a device
>+ * @dev: Device to set endpoint configuration on
>+ * @config_id: logical endpoint id on device
>+ *
>+ * Retrieves the logical_endpoint_config structure and frees the egress device.
>+ * Network device must already have association with RmNet Data driver
>+ */
>+static int rmnet_unset_logical_endpoint_config(struct net_device *dev,
>+ int config_id)
>+{
>+ LOGL("(%s, %d);", dev->name, config_id);
>+
>+ if (!dev || ((!_rmnet_is_physical_endpoint_associated(dev)) &&
>+ (!rmnet_vnd_is_vnd(dev)))) {
>+ return -EINVAL;
>+ }
>+
>+ return _rmnet_unset_logical_endpoint_config(dev, config_id);
>+}
>+
>+/* rmnet_free_vnd() - Free virtual network device node
>+ * @id: RmNet virtual device node id
>+ */
>+int rmnet_free_vnd(int id)
>+{
>+ LOGL("(%d);", id);
>+ return rmnet_vnd_free_dev(id);
>+}
>+
>+static void _rmnet_free_vnd_later(struct work_struct *work)
>+{
>+ int i;
>+ struct rmnet_free_vnd_work *fwork;
>+
>+ fwork = container_of(work, struct rmnet_free_vnd_work, work);
>+
>+ for (i = 0; i < fwork->count; i++)
>+ rmnet_free_vnd(fwork->vnd_id[i]);
>+ kfree(fwork);
>+}
>+
>+/* rmnet_force_unassociate_device() - Force a device to unassociate
>+ * @dev: Device to unassociate
>+ */
>+static void rmnet_force_unassociate_device(struct net_device *dev)
>+{
>+ int i, j;
>+ struct net_device *vndev;
>+ struct rmnet_phys_ep_conf_s *config;
>+ struct rmnet_logical_ep_conf_s *cfg;
>+ struct rmnet_free_vnd_work *vnd_work;
>+
>+ ASSERT_RTNL();
>+ if (!dev)
>+ return;
>+
>+ if (!_rmnet_is_physical_endpoint_associated(dev)) {
>+ LOGM("%s", "Called on unassociated device, skipping");
>+ return;
>+ }
>+
>+ vnd_work = kmalloc(sizeof(*vnd_work), GFP_KERNEL);
>+ if (!vnd_work)
>+ return;
>+
>+ INIT_WORK(&vnd_work->work, _rmnet_free_vnd_later);
>+ vnd_work->count = 0;
>+
>+ /* Check the VNDs for offending mappings */
>+ for (i = 0, j = 0; i < RMNET_MAX_VND &&
>+ j < RMNET_MAX_VND; i++) {
>+ vndev = rmnet_vnd_get_by_id(i);
>+ if (!vndev) {
>+ LOGL("VND %d not in use; skipping", i);
>+ continue;
>+ }
>+ cfg = rmnet_vnd_get_le_config(vndev);
>+ if (!cfg) {
>+ LOGD("Got NULL config from VND %d", i);
>+ continue;
>+ }
>+ if (cfg->refcount && (cfg->egress_dev == dev)) {
>+ /* Make sure the device is down before clearing any of
>+ * the mappings. Otherwise we could see a potential
>+ * race condition if packets are actively being
>+ * transmitted.
>+ */
>+ dev_close(vndev);
>+ rmnet_unset_logical_endpoint_config
>+ (vndev, RMNET_LOCAL_LOGICAL_ENDPOINT);
>+ vnd_work->vnd_id[j] = i;
>+ j++;
>+ }
>+ }
>+ if (j > 0) {
>+ vnd_work->count = j;
>+ schedule_work(&vnd_work->work);
>+ } else {
>+ kfree(vnd_work);
>+ }
>+
>+ config = _rmnet_get_phys_ep_config(dev);
>+
>+ if (config) {
>+ cfg = &config->local_ep;
>+
>+ if (cfg && cfg->refcount)
>+ rmnet_unset_logical_endpoint_config
>+ (cfg->egress_dev, RMNET_LOCAL_LOGICAL_ENDPOINT);
>+ }
>+
>+ /* Clear the mappings on the phys ep */
>+ rmnet_unset_logical_endpoint_config(dev, RMNET_LOCAL_LOGICAL_ENDPOINT);
>+ for (i = 0; i < RMNET_MAX_LOGICAL_EP; i++)
>+ rmnet_unset_logical_endpoint_config(dev, i);
>+ rmnet_unassociate_network_device(dev);
>+}
>+
>+/* rmnet_config_notify_cb() - Callback for netdevice notifier chain
>+ * @nb: Notifier block data
>+ * @event: Netdevice notifier event ID
>+ * @data: Contains a net device for which we are getting notified
>+ */
>+static int rmnet_config_notify_cb(struct notifier_block *nb,
>+ unsigned long event, void *data)
>+{
>+ struct net_device *dev = netdev_notifier_info_to_dev(data);
>+
>+ if (!dev)
>+ return NOTIFY_DONE;
>+
>+ switch (event) {
>+ case NETDEV_UNREGISTER_FINAL:
>+ case NETDEV_UNREGISTER:
>+ LOGM("Kernel is trying to unregister %s", dev->name);
>+ rmnet_force_unassociate_device(dev);
>+ break;
>+
>+ default:
>+ LOGD("Unhandeled event [%lu]", event);
>+ break;
>+ }
>+
>+ return NOTIFY_DONE;
>+}
>+
>+static struct notifier_block rmnet_dev_notifier = {
You should add "__read_mostly"
>+ .notifier_call = rmnet_config_notify_cb,
>+ .next = 0,
>+ .priority = 0
This initialization of 0s is not needed.
>+};
>+
>+static int rmnet_newlink(struct net *src_net, struct net_device *dev,
>+ struct nlattr *tb[], struct nlattr *data[])
>+{
>+ int ingress_format = RMNET_INGRESS_FORMAT_DEMUXING |
>+ RMNET_INGRESS_FORMAT_DEAGGREGATION |
>+ RMNET_INGRESS_FORMAT_MAP;
>+ int egress_format = RMNET_EGRESS_FORMAT_MUXING |
>+ RMNET_EGRESS_FORMAT_MAP;
>+ struct net_device *real_dev;
>+ int mode = RMNET_EPMODE_VND;
>+ u16 mux_id;
>+
>+ real_dev = __dev_get_by_index(src_net, nla_get_u32(tb[IFLA_LINK]));
>+ if (!real_dev)
>+ return -ENODEV;
>+
>+ if (!data[IFLA_RMNET_MUX_ID])
>+ return -EINVAL;
>+
>+ mux_id = nla_get_u16(data[IFLA_VLAN_ID]);
This is a bug I believe... ^^^^^^^
I'm pretty sure that you did not test this code.
>+ if (rmnet_vnd_newlink(mux_id, dev))
>+ return -EINVAL;
>+
>+ rmnet_associate_network_device(real_dev);
>+ rmnet_set_egress_data_format(real_dev, egress_format, 0, 0);
>+ rmnet_set_ingress_data_format(real_dev, ingress_format);
>+ rmnet_set_logical_endpoint_config(real_dev, mux_id, mode, dev);
>+ rmnet_set_logical_endpoint_config(dev, mux_id, mode, real_dev);
>+ return 0;
>+}
>+
>+static void rmnet_delink(struct net_device *dev, struct list_head *head)
>+{
>+ struct rmnet_logical_ep_conf_s *cfg;
>+ int mux_id;
>+
>+ mux_id = rmnet_vnd_is_vnd(dev);
>+ if (!mux_id)
>+ return;
>+
>+/* rmnet_vnd_is_vnd() gives mux_id + 1, so subtract 1 to get the correct mux_id
>+ */
Fix this comment format.
>+ mux_id--;
>+ cfg = rmnet_vnd_get_le_config(dev);
>+
>+ if (cfg && cfg->refcount) {
>+ _rmnet_unset_logical_endpoint_config(cfg->egress_dev, mux_id);
>+ _rmnet_unset_logical_endpoint_config(dev, mux_id);
>+ rmnet_vnd_remove_ref_dev(mux_id);
>+ rmnet_unassociate_network_device(cfg->egress_dev);
>+ }
>+
>+ unregister_netdevice_queue(dev, head);
>+}
>+
>+static int rmnet_rtnl_validate(struct nlattr *tb[], struct nlattr *data[])
>+{
>+ u16 mux_id;
>+
>+ if (!data || !data[IFLA_RMNET_MUX_ID])
>+ return -EINVAL;
>+
>+ mux_id = nla_get_u16(data[IFLA_RMNET_MUX_ID]);
>+ if (!mux_id || mux_id > (RMNET_MAX_LOGICAL_EP - 1))
>+ return -ERANGE;
>+
>+ return 0;
>+}
>+
>+static size_t rmnet_get_size(const struct net_device *dev)
>+{
>+ return nla_total_size(2); /* IFLA_RMNET_MUX_ID */
>+}
>+
>+struct rtnl_link_ops rmnet_link_ops __read_mostly = {
>+ .kind = "rmnet",
>+ .maxtype = __IFLA_RMNET_MAX,
>+ .priv_size = sizeof(struct rmnet_vnd_private_s),
>+ .setup = rmnet_vnd_setup,
>+ .validate = rmnet_rtnl_validate,
>+ .newlink = rmnet_newlink,
>+ .dellink = rmnet_delink,
>+ .get_size = rmnet_get_size,
>+};
>+
>+int rmnet_config_init(void)
>+{
>+ int rc;
>+
>+ rc = register_netdevice_notifier(&rmnet_dev_notifier);
>+ if (rc != 0) {
>+ LOGE("Failed to register device notifier; rc=%d", rc);
>+ return rc;
>+ }
>+
>+ rc = rtnl_link_register(&rmnet_link_ops);
>+ if (rc != 0) {
>+ unregister_netdevice_notifier(&rmnet_dev_notifier);
>+ LOGE("Failed to register netlink handler; rc=%d", rc);
>+ return rc;
>+ }
>+ return rc;
>+}
>+
>+void rmnet_config_exit(void)
>+{
>+ unregister_netdevice_notifier(&rmnet_dev_notifier);
>+ rtnl_link_unregister(&rmnet_link_ops);
>+}
>diff --git a/drivers/net/rmnet/rmnet_config.h b/drivers/net/rmnet/rmnet_config.h
>new file mode 100644
>index 0000000..0ef58e8
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_config.h
>@@ -0,0 +1,79 @@
>+/* Copyright (c) 2013-2014, 2016-2017 The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ * RMNET Data configuration engine
>+ *
>+ */
>+
>+#include <linux/types.h>
>+#include <linux/time.h>
>+#include <linux/skbuff.h>
>+
>+#ifndef _RMNET_CONFIG_H_
>+#define _RMNET_CONFIG_H_
>+
>+#define RMNET_MAX_LOGICAL_EP 255
>+
>+/* struct rmnet_logical_ep_conf_s - Logical end-point configuration
>+ *
>+ * @refcount: Reference count for this endpoint. 0 signifies the endpoint is not
>+ * configured for use
>+ * @rmnet_mode: Specifies how the traffic should be finally delivered. Possible
>+ * options are available in enum rmnet_config_endpoint_modes_e
>+ * @mux_id: Virtual channel ID used by MAP protocol
>+ * @egress_dev: Next device to deliver the packet to. Exact usage of this
>+ * parmeter depends on the rmnet_mode
>+ */
>+struct rmnet_logical_ep_conf_s {
>+ u8 refcount;
>+ u8 rmnet_mode;
>+ u8 mux_id;
>+ struct timespec flush_time;
>+ struct net_device *egress_dev;
>+};
>+
>+/* struct rmnet_phys_ep_conf_s - Physical endpoint configuration
>+ * One instance of this structure is instantiated for each net_device associated
>+ * with rmnet.
>+ *
>+ * @dev: The device which is associated with rmnet. Corresponds to this
>+ * specific instance of rmnet_phys_ep_conf_s
>+ * @local_ep: Default non-muxed endpoint. Used for non-MAP protocols/formats
>+ * @muxed_ep: All multiplexed logical endpoints associated with this device
>+ * @ingress_data_format: RMNET_INGRESS_FORMAT_* flags from rmnet.h
>+ * @egress_data_format: RMNET_EGRESS_FORMAT_* flags from rmnet.h
>+ *
>+ * @egress_agg_size: Maximum size (bytes) of data which should be aggregated
>+ * @egress_agg_count: Maximum count (packets) of data which should be aggregated
>+ * Smaller of the two parameters above are chosen for
>+ * aggregation
>+ * @tail_spacing: Guaranteed padding (bytes) when de-aggregating ingress frames
>+ * @agg_time: Wall clock time when aggregated frame was created
>+ * @agg_last: Last time the aggregation routing was invoked
>+ */
>+struct rmnet_phys_ep_conf_s {
>+ struct net_device *dev;
>+ struct rmnet_logical_ep_conf_s local_ep;
>+ struct rmnet_logical_ep_conf_s muxed_ep[RMNET_MAX_LOGICAL_EP];
>+ u32 ingress_data_format;
>+ u32 egress_data_format;
>+};
>+
>+int rmnet_config_init(void);
>+void rmnet_config_exit(void);
>+int rmnet_free_vnd(int id);
>+
>+extern struct rtnl_link_ops rmnet_link_ops;
>+
>+struct rmnet_vnd_private_s {
>+ struct rmnet_logical_ep_conf_s local_ep;
>+};
>+#endif /* _RMNET_CONFIG_H_ */
>diff --git a/drivers/net/rmnet/rmnet_handlers.c b/drivers/net/rmnet/rmnet_handlers.c
>new file mode 100644
>index 0000000..bf8b3bb
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_handlers.c
>@@ -0,0 +1,517 @@
>+/* Copyright (c) 2013-2017, The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ * RMNET Data ingress/egress handler
>+ *
>+ */
>+
>+#include <linux/skbuff.h>
>+#include <linux/netdevice.h>
>+#include <linux/module.h>
>+#include <linux/rmnet.h>
>+#include <linux/netdev_features.h>
>+#include <linux/ip.h>
>+#include <linux/ipv6.h>
>+#include "rmnet_private.h"
>+#include "rmnet_config.h"
>+#include "rmnet_vnd.h"
>+#include "rmnet_map.h"
>+#include "rmnet_stats.h"
>+#include "rmnet_handlers.h"
>+
>+RMNET_LOG_MODULE(RMNET_LOGMASK_HANDLER);
>+
>+#ifdef CONFIG_RMNET_DEBUG
>+unsigned int dump_pkt_rx;
>+module_param(dump_pkt_rx, uint, 0644);
>+MODULE_PARM_DESC(dump_pkt_rx, "Dump packets entering ingress handler");
>+
>+unsigned int dump_pkt_tx;
>+module_param(dump_pkt_tx, uint, 0644);
>+MODULE_PARM_DESC(dump_pkt_tx, "Dump packets exiting egress handler");
>+#endif /* CONFIG_RMNET_DEBUG */
>+
>+#define RMNET_IP_VERSION_4 0x40
>+#define RMNET_IP_VERSION_6 0x60
>+
>+/* Helper Functions */
>+
>+/* __rmnet_set_skb_proto() - Set skb->protocol field
>+ * @skb: packet being modified
>+ *
>+ * Peek at the first byte of the packet and set the protocol. There is not
>+ * good way to determine if a packet has a MAP header. As of writing this,
>+ * the reserved bit in the MAP frame will prevent it from overlapping with
>+ * IPv4/IPv6 frames. This could change in the future!
>+ */
>+static inline void __rmnet_set_skb_proto(struct sk_buff *skb)
>+{
>+ switch (skb->data[0] & 0xF0) {
>+ case RMNET_IP_VERSION_4:
>+ skb->protocol = htons(ETH_P_IP);
>+ break;
>+ case RMNET_IP_VERSION_6:
>+ skb->protocol = htons(ETH_P_IPV6);
>+ break;
>+ default:
>+ skb->protocol = htons(ETH_P_MAP);
>+ break;
>+ }
>+}
>+
>+#ifdef CONFIG_RMNET_DEBUG
>+/* rmnet_print_packet() - Print packet / diagnostics
>+ * @skb: Packet to print
>+ * @printlen: Number of bytes to print
>+ * @dev: Name of interface
>+ * @dir: Character representing direction (e.g.. 'r' for receive)
>+ *
>+ * This function prints out raw bytes in an SKB. Use of this will have major
>+ * performance impacts and may even trigger watchdog resets if too much is being
>+ * printed. Hence, this should always be compiled out unless absolutely needed.
>+ */
>+void rmnet_print_packet(const struct sk_buff *skb, const char *dev, char dir)
No reason to have this function. One can use P_ALL tap to get skbs to
userspace.
>+{
>+ char buffer[200];
>+ unsigned int len, printlen;
>+ int i, buffloc = 0;
>+
>+ switch (dir) {
>+ case 'r':
>+ printlen = dump_pkt_rx;
>+ break;
>+
>+ case 't':
>+ printlen = dump_pkt_tx;
>+ break;
>+
>+ default:
>+ printlen = 0;
>+ break;
>+ }
>+
>+ if (!printlen)
>+ return;
>+
>+ pr_err("[%s][%c] - PKT skb->len=%d skb->head=%pK skb->data=%pK\n",
>+ dev, dir, skb->len, (void *)skb->head, (void *)skb->data);
>+ pr_err("[%s][%c] - PKT skb->tail=%pK skb->end=%pK\n",
>+ dev, dir, skb_tail_pointer(skb), skb_end_pointer(skb));
>+
>+ if (skb->len > 0)
>+ len = skb->len;
>+ else
>+ len = ((unsigned int)(uintptr_t)skb->end) -
>+ ((unsigned int)(uintptr_t)skb->data);
>+
>+ pr_err("[%s][%c] - PKT len: %d, printing first %d bytes\n",
>+ dev, dir, len, printlen);
>+
>+ memset(buffer, 0, sizeof(buffer));
>+ for (i = 0; (i < printlen) && (i < len); i++) {
>+ if ((i % 16) == 0) {
>+ pr_err("[%s][%c] - PKT%s\n", dev, dir, buffer);
>+ memset(buffer, 0, sizeof(buffer));
>+ buffloc = 0;
>+ buffloc += snprintf(&buffer[buffloc],
>+ sizeof(buffer) - buffloc, "%04X:",
>+ i);
>+ }
>+
>+ buffloc += snprintf(&buffer[buffloc], sizeof(buffer) - buffloc,
>+ " %02x", skb->data[i]);
>+ }
>+ pr_err("[%s][%c] - PKT%s\n", dev, dir, buffer);
>+}
>+#else
>+void rmnet_print_packet(const struct sk_buff *skb, const char *dev, char dir)
>+{
>+}
>+#endif /* CONFIG_RMNET_DEBUG */
>+
>+/* Generic handler */
>+
>+/* rmnet_bridge_handler() - Bridge related functionality
>+ */
Fix the comment format (you have it on multiple places)
>+static rx_handler_result_t rmnet_bridge_handler
>+ (struct sk_buff *skb, struct rmnet_logical_ep_conf_s *ep)
The formatting is incorrect:
static rx_handler_result_t
rmnet_bridge_handler(struct sk_buff *skb, struct rmnet_logical_ep_conf_s *ep)
>+{
>+ if (!ep->egress_dev) {
>+ LOGD("Missing egress device for packet arriving on %s",
>+ skb->dev->name);
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_BRDG_NO_EGRESS);
>+ } else {
>+ rmnet_egress_handler(skb, ep);
>+ }
>+
>+ return RX_HANDLER_CONSUMED;
>+}
>+
>+#ifdef NET_SKBUFF_DATA_USES_OFFSET
>+static void rmnet_reset_mac_header(struct sk_buff *skb)
>+{
>+ skb->mac_header = 0;
>+ skb->mac_len = 0;
>+}
>+#else
>+static void rmnet_reset_mac_header(struct sk_buff *skb)
>+{
>+ skb->mac_header = skb->network_header;
>+ skb->mac_len = 0;
>+}
>+#endif /*NET_SKBUFF_DATA_USES_OFFSET*/
>+
>+/* __rmnet_deliver_skb() - Deliver skb
>+ *
>+ * Determines where to deliver skb. Options are: consume by network stack,
>+ * pass to bridge handler, or pass to virtual network device
>+ */
>+static rx_handler_result_t __rmnet_deliver_skb
>+ (struct sk_buff *skb, struct rmnet_logical_ep_conf_s *ep)
>+{
>+ switch (ep->rmnet_mode) {
>+ case RMNET_EPMODE_NONE:
>+ return RX_HANDLER_PASS;
>+
>+ case RMNET_EPMODE_BRIDGE:
>+ return rmnet_bridge_handler(skb, ep);
>+
>+ case RMNET_EPMODE_VND:
>+ skb_reset_transport_header(skb);
>+ skb_reset_network_header(skb);
>+ switch (rmnet_vnd_rx_fixup(skb, skb->dev)) {
>+ case RX_HANDLER_CONSUMED:
>+ return RX_HANDLER_CONSUMED;
>+
>+ case RX_HANDLER_PASS:
>+ skb->pkt_type = PACKET_HOST;
>+ rmnet_reset_mac_header(skb);
>+ netif_receive_skb(skb);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+ return RX_HANDLER_PASS;
>+
>+ default:
>+ LOGD("Unknown ep mode %d", ep->rmnet_mode);
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_DELIVER_NO_EP);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+}
>+
>+/* rmnet_ingress_deliver_packet() - Ingress handler for raw IP and bridged
>+ * MAP packets.
>+ * @skb: Packet needing a destination.
>+ * @config: Physical end point configuration that the packet arrived on.
>+ */
>+static rx_handler_result_t rmnet_ingress_deliver_packet
>+ (struct sk_buff *skb, struct rmnet_phys_ep_conf_s *config)
>+{
>+ if (!config) {
>+ LOGD("%s", "NULL physical EP provided");
>+ kfree_skb(skb);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+
>+ if (!(config->local_ep.refcount)) {
>+ LOGD("Packet on %s has no local endpoint configuration",
>+ skb->dev->name);
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_IPINGRESS_NO_EP);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+
>+ skb->dev = config->local_ep.egress_dev;
>+
>+ return __rmnet_deliver_skb(skb, &config->local_ep);
>+}
>+
>+/* MAP handler */
>+
>+/* _rmnet_map_ingress_handler() - Actual MAP ingress handler
>+ * @skb: Packet being received
>+ * @config: Physical endpoint configuration for the ingress device
>+ *
>+ * Most MAP ingress functions are processed here. Packets are processed
>+ * individually; aggregated packets should use rmnet_map_ingress_handler()
>+ */
>+static rx_handler_result_t _rmnet_map_ingress_handler
>+ (struct sk_buff *skb, struct rmnet_phys_ep_conf_s *config)
>+{
>+ struct rmnet_logical_ep_conf_s *ep;
>+ u8 mux_id;
>+ u16 len;
>+
>+ if (RMNET_MAP_GET_CD_BIT(skb)) {
>+ if (config->ingress_data_format
>+ & RMNET_INGRESS_FORMAT_MAP_COMMANDS)
>+ return rmnet_map_command(skb, config);
>+
>+ LOGM("MAP command packet on %s; %s", skb->dev->name,
>+ "Not configured for MAP commands");
>+ rmnet_kfree_skb(skb,
>+ RMNET_STATS_SKBFREE_INGRESS_NOT_EXPECT_MAPC);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+
>+ mux_id = RMNET_MAP_GET_MUX_ID(skb);
>+ len = RMNET_MAP_GET_LENGTH(skb) - RMNET_MAP_GET_PAD(skb);
>+
>+ if (mux_id >= RMNET_MAX_LOGICAL_EP) {
>+ LOGD("Got packet on %s with bad mux id %d",
>+ skb->dev->name, mux_id);
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_MAPINGRESS_BAD_MUX);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+
>+ ep = &config->muxed_ep[mux_id];
>+
>+ if (!ep->refcount) {
>+ LOGD("Packet on %s:%d; has no logical endpoint config",
>+ skb->dev->name, mux_id);
>+
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_MAPINGRESS_MUX_NO_EP);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+
>+ if (config->ingress_data_format & RMNET_INGRESS_FORMAT_DEMUXING)
>+ skb->dev = ep->egress_dev;
>+
>+ /* Subtract MAP header */
>+ skb_pull(skb, sizeof(struct rmnet_map_header_s));
>+ skb_trim(skb, len);
>+ __rmnet_set_skb_proto(skb);
>+ return __rmnet_deliver_skb(skb, ep);
>+}
>+
>+/* rmnet_map_ingress_handler() - MAP ingress handler
>+ * @skb: Packet being received
>+ * @config: Physical endpoint configuration for the ingress device
>+ *
>+ * Called if and only if MAP is configured in the ingress device's ingress data
>+ * format. Deaggregation is done here, actual MAP processing is done in
>+ * _rmnet_map_ingress_handler().
>+ */
>+static rx_handler_result_t rmnet_map_ingress_handler
>+ (struct sk_buff *skb, struct rmnet_phys_ep_conf_s *config)
>+{
>+ struct sk_buff *skbn;
>+ int rc, co = 0;
>+
>+ if (config->ingress_data_format & RMNET_INGRESS_FORMAT_DEAGGREGATION) {
>+ while ((skbn = rmnet_map_deaggregate(skb, config)) != NULL) {
>+ _rmnet_map_ingress_handler(skbn, config);
>+ co++;
>+ }
>+ LOGD("De-aggregated %d packets", co);
>+ rmnet_stats_deagg_pkts(co);
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_MAPINGRESS_AGGBUF);
>+ rc = RX_HANDLER_CONSUMED;
>+ } else {
>+ rc = _rmnet_map_ingress_handler(skb, config);
>+ }
>+
>+ return rc;
>+}
>+
>+/* rmnet_map_egress_handler() - MAP egress handler
>+ * @skb: Packet being sent
>+ * @config: Physical endpoint configuration for the egress device
>+ * @ep: logical endpoint configuration of the packet originator
>+ * (e.g.. RmNet virtual network device)
>+ * @orig_dev: The originator vnd device
>+ *
>+ * Called if and only if MAP is configured in the egress device's egress data
>+ * format. Will expand skb if there is insufficient headroom for MAP protocol.
>+ * Note: headroomexpansion will incur a performance penalty.
>+ */
>+static int rmnet_map_egress_handler(struct sk_buff *skb,
>+ struct rmnet_phys_ep_conf_s *config,
>+ struct rmnet_logical_ep_conf_s *ep,
>+ struct net_device *orig_dev)
>+{
>+ int required_headroom, additional_header_length;
>+ struct rmnet_map_header_s *map_header;
>+
>+ additional_header_length = 0;
>+ required_headroom = sizeof(struct rmnet_map_header_s);
>+
>+ LOGD("headroom of %d bytes", required_headroom);
>+
>+ if (skb_headroom(skb) < required_headroom) {
>+ if (pskb_expand_head(skb, required_headroom, 0, GFP_KERNEL)) {
>+ LOGD("Failed to add headroom of %d bytes",
>+ required_headroom);
>+ return RMNET_MAP_CONSUMED;
>+ }
>+ }
>+
>+ map_header = rmnet_map_add_map_header
>+ (skb, additional_header_length, RMNET_MAP_NO_PAD_BYTES);
>+ if (!map_header) {
>+ LOGD("%s", "Failed to add MAP header to egress packet");
>+ return RMNET_MAP_CONSUMED;
>+ }
>+
>+ if (config->egress_data_format & RMNET_EGRESS_FORMAT_MUXING) {
>+ if (ep->mux_id == 0xff)
>+ map_header->mux_id = 0;
>+ else
>+ map_header->mux_id = ep->mux_id;
>+ }
>+
>+ skb->protocol = htons(ETH_P_MAP);
>+
>+ return RMNET_MAP_SUCCESS;
>+}
>+
>+/* Ingress / Egress Entry Points */
>+
>+/* rmnet_ingress_handler() - Ingress handler entry point
>+ * @skb: Packet being received
>+ *
>+ * Processes packet as per ingress data format for receiving device. Logical
>+ * endpoint is determined from packet inspection. Packet is then sent to the
>+ * egress device listed in the logical endpoint configuration.
>+ */
>+rx_handler_result_t rmnet_ingress_handler(struct sk_buff *skb)
>+{
>+ struct rmnet_phys_ep_conf_s *config;
>+ struct net_device *dev;
>+ int rc;
>+
>+ if (!skb)
>+ return RX_HANDLER_CONSUMED;
>+
>+ dev = skb->dev;
>+ rmnet_print_packet(skb, dev->name, 'r');
>+
>+ config = (struct rmnet_phys_ep_conf_s *)
>+ rcu_dereference(skb->dev->rx_handler_data);
>+
>+ if (!config) {
Cannot happen. Please remove this.
>+ LOGD("%s is not associated with rmnet", skb->dev->name);
>+ kfree_skb(skb);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+
>+ /* Sometimes devices operate in ethernet mode even thouth there is no
>+ * ethernet header. This causes the skb->protocol to contain a bogus
>+ * value and the skb->data pointer to be off by 14 bytes. Fix it if
>+ * configured to do so
>+ */
>+ if (config->ingress_data_format & RMNET_INGRESS_FIX_ETHERNET) {
>+ skb_push(skb, RMNET_ETHERNET_HEADER_LENGTH);
>+ __rmnet_set_skb_proto(skb);
>+ }
>+
>+ if (config->ingress_data_format & RMNET_INGRESS_FORMAT_MAP) {
>+ rc = rmnet_map_ingress_handler(skb, config);
>+ } else {
>+ switch (ntohs(skb->protocol)) {
>+ case ETH_P_MAP:
>+ if (config->local_ep.rmnet_mode ==
>+ RMNET_EPMODE_BRIDGE) {
>+ rc = rmnet_ingress_deliver_packet(skb, config);
>+ } else {
>+ LOGD("MAP packet on %s; MAP not set",
>+ dev->name);
>+ rmnet_kfree_skb
>+ (skb,
>+ RMNET_STATS_SKBFREE_INGRESS_NOT_EXPECT_MAPD);
very odd formatting. Please fix.
>+ rc = RX_HANDLER_CONSUMED;
>+ }
>+ break;
>+
>+ case ETH_P_ARP:
>+ case ETH_P_IP:
>+ case ETH_P_IPV6:
>+ rc = rmnet_ingress_deliver_packet(skb, config);
>+ break;
>+
>+ default:
>+ LOGD("Unknown skb->proto 0x%04X\n",
>+ ntohs(skb->protocol) & 0xFFFF);
>+ rc = RX_HANDLER_PASS;
>+ }
>+ }
>+
>+ return rc;
>+}
>+
>+/* rmnet_rx_handler() - Rx handler callback registered with kernel
>+ * @pskb: Packet to be processed by rx handler
>+ *
>+ * Standard kernel-expected footprint for rx handlers. Calls
>+ * rmnet_ingress_handler with correctly formatted arguments
>+ */
>+rx_handler_result_t rmnet_rx_handler(struct sk_buff **pskb)
>+{
>+ return rmnet_ingress_handler(*pskb);
>+}
>+
>+/* rmnet_egress_handler() - Egress handler entry point
>+ * @skb: packet to transmit
>+ * @ep: logical endpoint configuration of the packet originator
>+ * (e.g.. RmNet virtual network device)
>+ *
>+ * Modifies packet as per logical endpoint configuration and egress data format
>+ * for egress device configured in logical endpoint. Packet is then transmitted
>+ * on the egress device.
>+ */
>+void rmnet_egress_handler(struct sk_buff *skb,
>+ struct rmnet_logical_ep_conf_s *ep)
>+{
>+ struct rmnet_phys_ep_conf_s *config;
>+ struct net_device *orig_dev;
>+ int rc;
>+
>+ orig_dev = skb->dev;
>+ skb->dev = ep->egress_dev;
>+
>+ config = (struct rmnet_phys_ep_conf_s *)
>+ rcu_dereference(skb->dev->rx_handler_data);
This is certainly a misuse of dev->rx_handler_data. Dev private of a
function arg to carry the pointer around.
>+
>+ if (!config) {
>+ LOGD("%s is not associated with rmnet", skb->dev->name);
>+ kfree_skb(skb);
>+ return;
>+ }
>+
>+ LOGD("Packet going out on %s with egress format 0x%08X",
>+ skb->dev->name, config->egress_data_format);
>+
>+ if (config->egress_data_format & RMNET_EGRESS_FORMAT_MAP) {
>+ switch (rmnet_map_egress_handler(skb, config, ep, orig_dev)) {
>+ case RMNET_MAP_CONSUMED:
>+ LOGD("%s", "MAP process consumed packet");
>+ return;
>+
>+ case RMNET_MAP_SUCCESS:
>+ break;
>+
>+ default:
>+ LOGD("MAP egress failed on packet on %s",
>+ skb->dev->name);
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_EGR_MAPFAIL);
>+ return;
>+ }
>+ }
>+
>+ if (ep->rmnet_mode == RMNET_EPMODE_VND)
>+ rmnet_vnd_tx_fixup(skb, orig_dev);
>+
>+ rmnet_print_packet(skb, skb->dev->name, 't');
>+ rc = dev_queue_xmit(skb);
>+ if (rc != 0) {
>+ LOGD("Failed to queue packet for transmission on [%s]",
>+ skb->dev->name);
>+ }
>+ rmnet_stats_queue_xmit(rc, RMNET_STATS_QUEUE_XMIT_EGRESS);
>+}
>diff --git a/drivers/net/rmnet/rmnet_handlers.h b/drivers/net/rmnet/rmnet_handlers.h
>new file mode 100644
>index 0000000..43c42c2
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_handlers.h
>@@ -0,0 +1,24 @@
>+/* Copyright (c) 2013, 2016-2017 The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ * RMNET Data ingress/egress handler
>+ *
>+ */
>+
>+#ifndef _RMNET_HANDLERS_H_
>+#define _RMNET_HANDLERS_H_
>+
>+void rmnet_egress_handler(struct sk_buff *skb,
>+ struct rmnet_logical_ep_conf_s *ep);
>+
>+rx_handler_result_t rmnet_rx_handler(struct sk_buff **pskb);
>+
>+#endif /* _RMNET_HANDLERS_H_ */
>diff --git a/drivers/net/rmnet/rmnet_main.c b/drivers/net/rmnet/rmnet_main.c
>new file mode 100644
>index 0000000..f8b7a20
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_main.c
>@@ -0,0 +1,52 @@
>+/* Copyright (c) 2013-2014, 2016-2017 The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ *
>+ * RMNET Data generic framework
>+ *
>+ */
>+
>+#include <linux/module.h>
>+#include <linux/kernel.h>
>+#include <linux/export.h>
>+#include "rmnet_private.h"
>+#include "rmnet_config.h"
>+#include "rmnet_vnd.h"
>+
>+/* Module Parameters */
>+unsigned int rmnet_log_level = RMNET_LOG_LVL_ERR | RMNET_LOG_LVL_HI;
>+module_param(rmnet_log_level, uint, 0644);
>+MODULE_PARM_DESC(log_level, "Logging level");
>+
>+unsigned int rmnet_log_module_mask;
>+module_param(rmnet_log_module_mask, uint, 0644);
>+MODULE_PARM_DESC(rmnet_log_module_mask, "Logging module mask");
No module options please.
>+
>+/* Startup/Shutdown */
>+
>+static int __init rmnet_init(void)
>+{
>+ rmnet_config_init();
>+ rmnet_vnd_init();
>+
>+ LOGL("%s", "RMNET Data driver loaded successfully");
>+ return 0;
>+}
>+
>+static void __exit rmnet_exit(void)
>+{
>+ rmnet_config_exit();
>+ rmnet_vnd_exit();
>+}
>+
>+module_init(rmnet_init)
>+module_exit(rmnet_exit)
>+MODULE_LICENSE("GPL v2");
>diff --git a/drivers/net/rmnet/rmnet_map.h b/drivers/net/rmnet/rmnet_map.h
>new file mode 100644
>index 0000000..7d533aa
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_map.h
>@@ -0,0 +1,100 @@
>+/* Copyright (c) 2013-2017, The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ */
>+
>+#include <linux/types.h>
>+#include <linux/spinlock.h>
>+
>+#ifndef _RMNET_MAP_H_
>+#define _RMNET_MAP_H_
>+
>+struct rmnet_map_control_command_s {
>+ u8 command_name;
>+ u8 cmd_type:2;
>+ u8 reserved:6;
>+ u16 reserved2;
>+ u32 transaction_id;
>+ union {
>+ u8 data[65528];
>+ struct {
>+ u16 ip_family:2;
>+ u16 reserved:14;
>+ u16 flow_control_seq_num;
>+ u32 qos_id;
>+ } flow_control;
>+ };
>+} __aligned(1);
>+
>+enum rmnet_map_results_e {
>+ RMNET_MAP_SUCCESS,
>+ RMNET_MAP_CONSUMED,
>+ RMNET_MAP_GENERAL_FAILURE,
>+ RMNET_MAP_NOT_ENABLED,
>+ RMNET_MAP_FAILED_AGGREGATION,
>+ RMNET_MAP_FAILED_MUX
>+};
>+
>+enum rmnet_map_mux_errors_e {
>+ RMNET_MAP_MUX_SUCCESS,
>+ RMNET_MAP_MUX_INVALID_MUX_ID,
>+ RMNET_MAP_MUX_INVALID_PAD_LENGTH,
>+ RMNET_MAP_MUX_INVALID_PKT_LENGTH,
>+ /* This should always be the last element */
>+ RMNET_MAP_MUX_ENUM_LENGTH
>+};
>+
>+enum rmnet_map_commands_e {
>+ RMNET_MAP_COMMAND_NONE,
>+ RMNET_MAP_COMMAND_FLOW_DISABLE,
>+ RMNET_MAP_COMMAND_FLOW_ENABLE,
>+ /* These should always be the last 2 elements */
>+ RMNET_MAP_COMMAND_UNKNOWN,
>+ RMNET_MAP_COMMAND_ENUM_LENGTH
>+};
>+
>+struct rmnet_map_header_s {
>+ u8 pad_len:6;
>+ u8 reserved_bit:1;
>+ u8 cd_bit:1;
>+ u8 mux_id;
>+ u16 pkt_len;
>+} __aligned(1);
>+
>+#define RMNET_MAP_GET_MUX_ID(Y) (((struct rmnet_map_header_s *) \
>+ (Y)->data)->mux_id)
>+#define RMNET_MAP_GET_CD_BIT(Y) (((struct rmnet_map_header_s *) \
>+ (Y)->data)->cd_bit)
>+#define RMNET_MAP_GET_PAD(Y) (((struct rmnet_map_header_s *) \
>+ (Y)->data)->pad_len)
>+#define RMNET_MAP_GET_CMD_START(Y) ((struct rmnet_map_control_command_s *) \
>+ ((Y)->data + \
>+ sizeof(struct rmnet_map_header_s)))
>+#define RMNET_MAP_GET_LENGTH(Y) (ntohs(((struct rmnet_map_header_s *) \
>+ (Y)->data)->pkt_len))
>+
>+#define RMNET_MAP_COMMAND_REQUEST 0
>+#define RMNET_MAP_COMMAND_ACK 1
>+#define RMNET_MAP_COMMAND_UNSUPPORTED 2
>+#define RMNET_MAP_COMMAND_INVALID 3
>+
>+#define RMNET_MAP_NO_PAD_BYTES 0
>+#define RMNET_MAP_ADD_PAD_BYTES 1
>+
>+u8 rmnet_map_demultiplex(struct sk_buff *skb);
>+struct sk_buff *rmnet_map_deaggregate(struct sk_buff *skb,
>+ struct rmnet_phys_ep_conf_s *config);
>+
>+struct rmnet_map_header_s *rmnet_map_add_map_header(struct sk_buff *skb,
>+ int hdrlen, int pad);
>+rx_handler_result_t rmnet_map_command(struct sk_buff *skb,
>+ struct rmnet_phys_ep_conf_s *config);
>+
>+#endif /* _RMNET_MAP_H_ */
>diff --git a/drivers/net/rmnet/rmnet_map_command.c b/drivers/net/rmnet/rmnet_map_command.c
>new file mode 100644
>index 0000000..13bcee3
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_map_command.c
>@@ -0,0 +1,180 @@
>+/* Copyright (c) 2013-2017, The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ */
>+
>+#include <linux/module.h>
>+#include <linux/kernel.h>
>+#include <linux/skbuff.h>
>+#include <linux/netdevice.h>
>+#include <linux/rmnet.h>
>+#include <net/pkt_sched.h>
>+#include "rmnet_config.h"
>+#include "rmnet_map.h"
>+#include "rmnet_private.h"
>+#include "rmnet_vnd.h"
>+#include "rmnet_stats.h"
>+
>+RMNET_LOG_MODULE(RMNET_LOGMASK_MAPC);
>+
>+unsigned long int rmnet_map_command_stats[RMNET_MAP_COMMAND_ENUM_LENGTH];
>+module_param_array(rmnet_map_command_stats, ulong, 0, 0444);
>+MODULE_PARM_DESC(rmnet_map_command_stats, "MAP command statistics");
>+
>+/* rmnet_map_do_flow_control() - Process MAP flow control command
>+ * @skb: Socket buffer containing the MAP flow control message
>+ * @config: Physical end-point configuration of ingress device
>+ * @enable: boolean for enable/disable
>+ *
>+ * Process in-band MAP flow control messages. Assumes mux ID is mapped to a
>+ * RmNet Data vitrual network device.
>+ *
>+ * Return:
>+ * - RMNET_MAP_COMMAND_UNSUPPORTED on any error
>+ * - RMNET_MAP_COMMAND_ACK on success
>+ */
>+static u8 rmnet_map_do_flow_control(struct sk_buff *skb,
>+ struct rmnet_phys_ep_conf_s *config,
>+ int enable)
>+{
>+ struct rmnet_map_control_command_s *cmd;
>+ struct net_device *vnd;
>+ struct rmnet_logical_ep_conf_s *ep;
>+ u8 mux_id;
>+ u16 ip_family;
>+ u16 fc_seq;
>+ u32 qos_id;
>+ int r;
>+
>+ if (unlikely(!skb || !config))
>+ return RX_HANDLER_CONSUMED;
>+
>+ mux_id = RMNET_MAP_GET_MUX_ID(skb);
>+ cmd = RMNET_MAP_GET_CMD_START(skb);
>+
>+ if (mux_id >= RMNET_MAX_LOGICAL_EP) {
>+ LOGD("Got packet on %s with bad mux id %d",
>+ skb->dev->name, mux_id);
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_MAPC_BAD_MUX);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+
>+ ep = &config->muxed_ep[mux_id];
>+
>+ if (!ep->refcount) {
>+ LOGD("Packet on %s:%d; has no logical endpoint config",
>+ skb->dev->name, mux_id);
>+
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_MAPC_MUX_NO_EP);
>+ return RX_HANDLER_CONSUMED;
>+ }
>+
>+ vnd = ep->egress_dev;
>+
>+ ip_family = cmd->flow_control.ip_family;
>+ fc_seq = ntohs(cmd->flow_control.flow_control_seq_num);
>+ qos_id = ntohl(cmd->flow_control.qos_id);
>+
>+ /* Ignore the ip family and pass the sequence number for both v4 and v6
>+ * sequence. User space does not support creating dedicated flows for
>+ * the 2 protocols
>+ */
>+ r = rmnet_vnd_do_flow_control(vnd, enable);
>+ LOGD("dev:%s, qos_id:0x%08X, ip_family:%hd, fc_seq %hd, en:%d",
>+ skb->dev->name, qos_id, ip_family & 3, fc_seq, enable);
>+
>+ if (r) {
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_MAPC_UNSUPPORTED);
>+ return RMNET_MAP_COMMAND_UNSUPPORTED;
>+ } else {
>+ return RMNET_MAP_COMMAND_ACK;
>+ }
>+}
>+
>+/* rmnet_map_send_ack() - Send N/ACK message for MAP commands
>+ * @skb: Socket buffer containing the MAP command message
>+ * @type: N/ACK message selector
>+ * @config: Physical end-point configuration of ingress device
>+ *
>+ * skb is modified to contain the message type selector. The message is then
>+ * transmitted on skb->dev. Note that this function grabs global Tx lock on
>+ * skb->dev for latency reasons.
>+ *
>+ * Return:
>+ * - void
>+ */
>+static void rmnet_map_send_ack(struct sk_buff *skb,
>+ unsigned char type,
>+ struct rmnet_phys_ep_conf_s *config)
>+{
>+ struct rmnet_map_control_command_s *cmd;
>+ int xmit_status;
>+
>+ if (unlikely(!skb))
>+ return;
>+
>+ skb->protocol = htons(ETH_P_MAP);
>+
>+ cmd = RMNET_MAP_GET_CMD_START(skb);
>+ cmd->cmd_type = type & 0x03;
>+
>+ netif_tx_lock(skb->dev);
>+ xmit_status = skb->dev->netdev_ops->ndo_start_xmit(skb, skb->dev);
>+ netif_tx_unlock(skb->dev);
>+
>+ LOGD("MAP command ACK=%hhu sent with rc: %d", type & 0x03, xmit_status);
>+}
>+
>+/* rmnet_map_command() - Entry point for handling MAP commands
>+ * @skb: Socket buffer containing the MAP command message
>+ * @config: Physical end-point configuration of ingress device
>+ *
>+ * Process MAP command frame and send N/ACK message as appropriate. Message cmd
>+ * name is decoded here and appropriate handler is called.
>+ *
>+ * Return:
>+ * - RX_HANDLER_CONSUMED. Command frames are always consumed.
>+ */
>+rx_handler_result_t rmnet_map_command(struct sk_buff *skb,
>+ struct rmnet_phys_ep_conf_s *config)
>+{
>+ struct rmnet_map_control_command_s *cmd;
>+ unsigned char command_name;
>+ unsigned char rc = 0;
>+
>+ if (unlikely(!skb))
>+ return RX_HANDLER_CONSUMED;
>+
>+ cmd = RMNET_MAP_GET_CMD_START(skb);
>+ command_name = cmd->command_name;
>+
>+ if (command_name < RMNET_MAP_COMMAND_ENUM_LENGTH)
>+ rmnet_map_command_stats[command_name]++;
>+
>+ switch (command_name) {
>+ case RMNET_MAP_COMMAND_FLOW_ENABLE:
>+ rc = rmnet_map_do_flow_control(skb, config, 1);
>+ break;
>+
>+ case RMNET_MAP_COMMAND_FLOW_DISABLE:
>+ rc = rmnet_map_do_flow_control(skb, config, 0);
>+ break;
>+
>+ default:
>+ rmnet_map_command_stats[RMNET_MAP_COMMAND_UNKNOWN]++;
>+ LOGM("Uknown MAP command: %d", command_name);
>+ rc = RMNET_MAP_COMMAND_UNSUPPORTED;
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_MAPC_UNSUPPORTED);
>+ break;
>+ }
>+ if (rc == RMNET_MAP_COMMAND_ACK)
>+ rmnet_map_send_ack(skb, rc, config);
>+ return RX_HANDLER_CONSUMED;
>+}
>diff --git a/drivers/net/rmnet/rmnet_map_data.c b/drivers/net/rmnet/rmnet_map_data.c
>new file mode 100644
>index 0000000..93af3c9
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_map_data.c
>@@ -0,0 +1,145 @@
>+/* Copyright (c) 2013-2017, The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ * RMNET Data MAP protocol
>+ *
>+ */
>+
>+#include <linux/module.h>
>+#include <linux/kernel.h>
>+#include <linux/skbuff.h>
>+#include <linux/netdevice.h>
>+#include <linux/rmnet.h>
>+#include <linux/spinlock.h>
>+#include <linux/workqueue.h>
>+#include <linux/time.h>
>+#include <linux/ip.h>
>+#include <linux/ipv6.h>
>+#include <linux/udp.h>
>+#include <linux/tcp.h>
>+#include <linux/in.h>
>+#include <net/ip.h>
>+#include <net/checksum.h>
>+#include <net/ip6_checksum.h>
>+#include "rmnet_config.h"
>+#include "rmnet_map.h"
>+#include "rmnet_private.h"
>+#include "rmnet_stats.h"
>+
>+RMNET_LOG_MODULE(RMNET_LOGMASK_MAPD);
>+
>+#define RMNET_MAP_DEAGGR_SPACING 64
>+#define RMNET_MAP_DEAGGR_HEADROOM (RMNET_MAP_DEAGGR_SPACING / 2)
>+
>+/* rmnet_map_add_map_header() - Adds MAP header to front of skb->data
>+ * @skb: Socket buffer ("packet") to modify
>+ * @hdrlen: Number of bytes of header data which should not be included in
>+ * MAP length field
>+ * @pad: Specify if padding the MAP packet to make it 4 byte aligned is
>+ * necessary
>+ *
>+ * Padding is calculated and set appropriately in MAP header. Mux ID is
>+ * initialized to 0.
>+ *
>+ * Return:
>+ * - Pointer to MAP structure
>+ * - 0 (null) if insufficient headroom
>+ * - 0 (null) if insufficient tailroom for padding bytes
>+ */
>+struct rmnet_map_header_s *rmnet_map_add_map_header(struct sk_buff *skb,
>+ int hdrlen, int pad)
>+{
>+ u32 padding, map_datalen;
>+ u8 *padbytes;
>+ struct rmnet_map_header_s *map_header;
>+
>+ if (skb_headroom(skb) < sizeof(struct rmnet_map_header_s))
>+ return 0;
>+
>+ map_datalen = skb->len - hdrlen;
>+ map_header = (struct rmnet_map_header_s *)
>+ skb_push(skb, sizeof(struct rmnet_map_header_s));
>+ memset(map_header, 0, sizeof(struct rmnet_map_header_s));
>+
>+ if (pad == RMNET_MAP_NO_PAD_BYTES) {
>+ map_header->pkt_len = htons(map_datalen);
>+ return map_header;
>+ }
>+
>+ padding = ALIGN(map_datalen, 4) - map_datalen;
>+
>+ if (padding == 0)
>+ goto done;
>+
>+ if (skb_tailroom(skb) < padding)
>+ return 0;
>+
>+ padbytes = (u8 *)skb_put(skb, padding);
>+ LOGD("pad: %d", padding);
>+ memset(padbytes, 0, padding);
>+
>+done:
>+ map_header->pkt_len = htons(map_datalen + padding);
>+ map_header->pad_len = padding & 0x3F;
>+
>+ return map_header;
>+}
>+
>+/* rmnet_map_deaggregate() - Deaggregates a single packet
>+ * @skb: Source socket buffer containing multiple MAP frames
>+ * @config: Physical endpoint configuration of the ingress device
>+ *
>+ * A whole new buffer is allocated for each portion of an aggregated frame.
>+ * Caller should keep calling deaggregate() on the source skb until 0 is
>+ * returned, indicating that there are no more packets to deaggregate. Caller
>+ * is responsible for freeing the original skb.
>+ *
>+ * Return:
>+ * - Pointer to new skb
>+ * - 0 (null) if no more aggregated packets
>+ */
>+struct sk_buff *rmnet_map_deaggregate(struct sk_buff *skb,
>+ struct rmnet_phys_ep_conf_s *config)
>+{
>+ struct sk_buff *skbn;
>+ struct rmnet_map_header_s *maph;
>+ u32 packet_len;
>+
>+ if (skb->len == 0)
>+ return 0;
>+
>+ maph = (struct rmnet_map_header_s *)skb->data;
>+ packet_len = ntohs(maph->pkt_len) + sizeof(struct rmnet_map_header_s);
>+
>+ if ((((int)skb->len) - ((int)packet_len)) < 0) {
>+ LOGM("%s", "Got malformed packet. Dropping");
>+ return 0;
>+ }
>+
>+ skbn = alloc_skb(packet_len + RMNET_MAP_DEAGGR_SPACING, GFP_ATOMIC);
>+ if (!skbn)
>+ return 0;
>+
>+ skbn->dev = skb->dev;
>+ skb_reserve(skbn, RMNET_MAP_DEAGGR_HEADROOM);
>+ skb_put(skbn, packet_len);
>+ memcpy(skbn->data, skb->data, packet_len);
>+ skb_pull(skb, packet_len);
>+
>+ /* Some hardware can send us empty frames. Catch them */
>+ if (ntohs(maph->pkt_len) == 0) {
>+ LOGD("Dropping empty MAP frame");
>+ rmnet_kfree_skb(skbn, RMNET_STATS_SKBFREE_DEAGG_DATA_LEN_0);
>+ return 0;
>+ }
>+
>+ return skbn;
>+}
>diff --git a/drivers/net/rmnet/rmnet_private.h b/drivers/net/rmnet/rmnet_private.h
>new file mode 100644
>index 0000000..f27e0b3
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_private.h
>@@ -0,0 +1,76 @@
>+/* Copyright (c) 2013-2014, 2016-2017 The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ */
>+
>+#ifndef _RMNET_PRIVATE_H_
>+#define _RMNET_PRIVATE_H_
>+
>+#define RMNET_MAX_VND 32
>+#define RMNET_MAX_PACKET_SIZE 16384
>+#define RMNET_DFLT_PACKET_SIZE 1500
>+#define RMNET_DEV_NAME_STR "rmnet"
>+#define RMNET_NEEDED_HEADROOM 16
>+#define RMNET_TX_QUEUE_LEN 1000
>+#define RMNET_ETHERNET_HEADER_LENGTH 14
>+
>+extern unsigned int rmnet_log_level;
>+extern unsigned int rmnet_log_module_mask;
>+
>+#define RMNET_INIT_OK 0
>+#define RMNET_INIT_ERROR 1
Please use common error codes (0/-ENOMEM/-EINVAL/...)
>+
>+#define RMNET_LOG_LVL_DBG BIT(4)
>+#define RMNET_LOG_LVL_LOW BIT(3)
>+#define RMNET_LOG_LVL_MED BIT(2)
>+#define RMNET_LOG_LVL_HI BIT(1)
>+#define RMNET_LOG_LVL_ERR BIT(0)
>+
>+#define RMNET_LOG_MODULE(X) \
>+ static u32 rmnet_mod_mask = X
Don't use this custom helpers. Use existing loggign facilities.
>+
>+#define RMNET_LOGMASK_CONFIG BIT(0)
>+#define RMNET_LOGMASK_HANDLER BIT(1)
>+#define RMNET_LOGMASK_VND BIT(2)
>+#define RMNET_LOGMASK_MAPD BIT(3)
>+#define RMNET_LOGMASK_MAPC BIT(4)
>+
>+#define LOGE(fmt, ...) do { if (rmnet_log_level & RMNET_LOG_LVL_ERR) \
>+ pr_err("[RMNET:ERR] %s(): " fmt "\n", __func__, \
>+ ##__VA_ARGS__); \
>+ } while (0)
>+
>+#define LOGH(fmt, ...) do { if (rmnet_log_level & RMNET_LOG_LVL_HI) \
>+ pr_err("[RMNET:HI] %s(): " fmt "\n", __func__, \
>+ ##__VA_ARGS__); \
>+ } while (0)
>+
>+#define LOGM(fmt, ...) do { if (rmnet_log_level & RMNET_LOG_LVL_MED) \
>+ pr_warn("[RMNET:MED] %s(): " fmt "\n", __func__, \
>+ ##__VA_ARGS__); \
>+ } while (0)
>+
>+#define LOGL(fmt, ...) do { if (unlikely \
>+ (rmnet_log_level & RMNET_LOG_LVL_LOW)) \
>+ pr_notice("[RMNET:LOW] %s(): " fmt "\n", __func__, \
>+ ##__VA_ARGS__); \
>+ } while (0)
These look scarry. Please use netdev_err, dev_err and others instead.
>+
>+/* Don't use pr_debug as it is compiled out of the kernel. We can be sure of
>+ * minimal impact as LOGD is not enabled by default.
>+ */
>+#define LOGD(fmt, ...) do { if (unlikely( \
>+ (rmnet_log_level & RMNET_LOG_LVL_DBG) &&\
>+ (rmnet_log_module_mask & rmnet_mod_mask))) \
>+ pr_notice("[RMNET:DBG] %s(): " fmt "\n", __func__, \
>+ ##__VA_ARGS__); \
>+ } while (0)
>+
>+#endif /* _RMNET_PRIVATE_H_ */
>diff --git a/drivers/net/rmnet/rmnet_stats.c b/drivers/net/rmnet/rmnet_stats.c
>new file mode 100644
>index 0000000..d53ce38
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_stats.c
>@@ -0,0 +1,86 @@
>+/* Copyright (c) 2014, 2016-2017 The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ *
>+ * RMNET Data statistics
>+ *
>+ */
>+
>+#include <linux/module.h>
>+#include <linux/kernel.h>
>+#include <linux/export.h>
>+#include <linux/skbuff.h>
>+#include <linux/spinlock.h>
>+#include <linux/netdevice.h>
>+#include "rmnet_private.h"
>+#include "rmnet_stats.h"
>+#include "rmnet_config.h"
>+#include "rmnet_map.h"
>+
>+enum rmnet_deagg_e {
>+ RMNET_STATS_AGG_BUFF,
>+ RMNET_STATS_AGG_PKT,
>+ RMNET_STATS_AGG_MAX
>+};
>+
>+static DEFINE_SPINLOCK(rmnet_skb_free_lock);
>+unsigned long int skb_free[RMNET_STATS_SKBFREE_MAX];
>+module_param_array(skb_free, ulong, 0, 0444);
>+MODULE_PARM_DESC(skb_free, "SKBs dropped or freed");
>+
>+static DEFINE_SPINLOCK(rmnet_queue_xmit_lock);
>+unsigned long int queue_xmit[RMNET_STATS_QUEUE_XMIT_MAX * 2];
>+module_param_array(queue_xmit, ulong, 0, 0444);
>+MODULE_PARM_DESC(queue_xmit, "SKBs queued for transmit");
>+
>+static DEFINE_SPINLOCK(rmnet_deagg_count);
>+unsigned long int deagg_count[RMNET_STATS_AGG_MAX];
>+module_param_array(deagg_count, ulong, 0, 0444);
>+MODULE_PARM_DESC(deagg_count, "SKBs De-aggregated");
>+
>+void rmnet_kfree_skb(struct sk_buff *skb, unsigned int reason)
>+{
>+ unsigned long flags;
>+
>+ if (reason >= RMNET_STATS_SKBFREE_MAX)
>+ reason = RMNET_STATS_SKBFREE_UNKNOWN;
>+
>+ spin_lock_irqsave(&rmnet_skb_free_lock, flags);
>+ skb_free[reason]++;
>+ spin_unlock_irqrestore(&rmnet_skb_free_lock, flags);
>+
>+ if (skb)
>+ kfree_skb(skb);
>+}
>+
>+void rmnet_stats_queue_xmit(int rc, unsigned int reason)
>+{
>+ unsigned long flags;
>+
>+ if (rc != 0)
>+ reason += RMNET_STATS_QUEUE_XMIT_MAX;
>+ if (reason >= RMNET_STATS_QUEUE_XMIT_MAX * 2)
>+ reason = RMNET_STATS_SKBFREE_UNKNOWN;
>+
>+ spin_lock_irqsave(&rmnet_queue_xmit_lock, flags);
>+ queue_xmit[reason]++;
>+ spin_unlock_irqrestore(&rmnet_queue_xmit_lock, flags);
>+}
>+
>+void rmnet_stats_deagg_pkts(int aggcount)
>+{
>+ unsigned long flags;
>+
>+ spin_lock_irqsave(&rmnet_deagg_count, flags);
>+ deagg_count[RMNET_STATS_AGG_BUFF]++;
>+ deagg_count[RMNET_STATS_AGG_PKT] += aggcount;
>+ spin_unlock_irqrestore(&rmnet_deagg_count, flags);
>+}
>diff --git a/drivers/net/rmnet/rmnet_stats.h b/drivers/net/rmnet/rmnet_stats.h
>new file mode 100644
>index 0000000..c8d0469
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_stats.h
>@@ -0,0 +1,61 @@
>+/* Copyright (c) 2014, 2016-2017 The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ *
>+ * RMNET Data statistics
>+ *
>+ */
>+
>+#ifndef _RMNET_STATS_H_
>+#define _RMNET_STATS_H_
>+
>+enum rmnet_skb_free_e {
>+ RMNET_STATS_SKBFREE_UNKNOWN,
>+ RMNET_STATS_SKBFREE_BRDG_NO_EGRESS,
>+ RMNET_STATS_SKBFREE_DELIVER_NO_EP,
>+ RMNET_STATS_SKBFREE_IPINGRESS_NO_EP,
>+ RMNET_STATS_SKBFREE_MAPINGRESS_BAD_MUX,
>+ RMNET_STATS_SKBFREE_MAPINGRESS_MUX_NO_EP,
>+ RMNET_STATS_SKBFREE_MAPINGRESS_AGGBUF,
>+ RMNET_STATS_SKBFREE_INGRESS_NOT_EXPECT_MAPD,
>+ RMNET_STATS_SKBFREE_INGRESS_NOT_EXPECT_MAPC,
>+ RMNET_STATS_SKBFREE_EGR_MAPFAIL,
>+ RMNET_STATS_SKBFREE_VND_NO_EGRESS,
>+ RMNET_STATS_SKBFREE_MAPC_BAD_MUX,
>+ RMNET_STATS_SKBFREE_MAPC_MUX_NO_EP,
>+ RMNET_STATS_SKBFREE_AGG_CPY_EXPAND,
>+ RMNET_STATS_SKBFREE_AGG_INTO_BUFF,
>+ RMNET_STATS_SKBFREE_DEAGG_MALFORMED,
>+ RMNET_STATS_SKBFREE_DEAGG_CLONE_FAIL,
>+ RMNET_STATS_SKBFREE_DEAGG_UNKNOWN_IP_TYPE,
>+ RMNET_STATS_SKBFREE_DEAGG_DATA_LEN_0,
>+ RMNET_STATS_SKBFREE_INGRESS_BAD_MAP_CKSUM,
>+ RMNET_STATS_SKBFREE_MAPC_UNSUPPORTED,
>+ RMNET_STATS_SKBFREE_MAX
>+};
>+
>+enum rmnet_queue_xmit_e {
>+ RMNET_STATS_QUEUE_XMIT_UNKNOWN,
>+ RMNET_STATS_QUEUE_XMIT_EGRESS,
>+ RMNET_STATS_QUEUE_XMIT_AGG_FILL_BUFFER,
>+ RMNET_STATS_QUEUE_XMIT_AGG_TIMEOUT,
>+ RMNET_STATS_QUEUE_XMIT_AGG_CPY_EXP_FAIL,
>+ RMNET_STATS_QUEUE_XMIT_AGG_SKIP,
>+ RMNET_STATS_QUEUE_XMIT_MAX
>+};
>+
>+void rmnet_kfree_skb(struct sk_buff *skb, unsigned int reason);
>+void rmnet_stats_queue_xmit(int rc, unsigned int reason);
>+void rmnet_stats_deagg_pkts(int aggcount);
>+void rmnet_stats_agg_pkts(int aggcount);
>+void rmnet_stats_dl_checksum(unsigned int rc);
>+void rmnet_stats_ul_checksum(unsigned int rc);
>+#endif /* _RMNET_STATS_H_ */
>diff --git a/drivers/net/rmnet/rmnet_vnd.c b/drivers/net/rmnet/rmnet_vnd.c
>new file mode 100644
>index 0000000..a737d0e
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_vnd.c
>@@ -0,0 +1,353 @@
>+/* Copyright (c) 2013-2017, The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ *
>+ * RMNET Data virtual network driver
>+ *
>+ */
>+
>+#include <linux/types.h>
>+#include <linux/rmnet.h>
>+#include <linux/etherdevice.h>
>+#include <linux/if_arp.h>
>+#include <linux/spinlock.h>
>+#include <net/pkt_sched.h>
>+#include <linux/atomic.h>
>+#include "rmnet_config.h"
>+#include "rmnet_handlers.h"
>+#include "rmnet_private.h"
>+#include "rmnet_map.h"
>+#include "rmnet_vnd.h"
>+#include "rmnet_stats.h"
>+
>+RMNET_LOG_MODULE(RMNET_LOGMASK_VND);
>+
>+struct net_device *rmnet_devices[RMNET_MAX_VND];
Avoid this global variable.
>+
>+/* RX/TX Fixup */
>+
>+/* rmnet_vnd_rx_fixup() - Virtual Network Device receive fixup hook
>+ * @skb: Socket buffer ("packet") to modify
>+ * @dev: Virtual network device
>+ *
>+ * Additional VND specific packet processing for ingress packets
>+ */
>+int rmnet_vnd_rx_fixup(struct sk_buff *skb, struct net_device *dev)
>+{
>+ if (unlikely(!dev || !skb))
>+ return RX_HANDLER_CONSUMED;
>+
>+ dev->stats.rx_packets++;
>+ dev->stats.rx_bytes += skb->len;
>+
>+ return RX_HANDLER_PASS;
>+}
>+
>+/* rmnet_vnd_tx_fixup() - Virtual Network Device transmic fixup hook
>+ * @skb: Socket buffer ("packet") to modify
>+ * @dev: Virtual network device
>+ *
>+ * Additional VND specific packet processing for egress packets
>+ */
>+int rmnet_vnd_tx_fixup(struct sk_buff *skb, struct net_device *dev)
>+{
>+ struct rmnet_vnd_private_s *dev_conf;
>+
>+ dev_conf = (struct rmnet_vnd_private_s *)netdev_priv(dev);
>+
>+ if (unlikely(!dev || !skb))
>+ return RX_HANDLER_CONSUMED;
>+
>+ dev->stats.tx_packets++;
>+ dev->stats.tx_bytes += skb->len;
>+
>+ return RX_HANDLER_PASS;
>+}
>+
>+/* Network Device Operations */
>+
>+/* rmnet_vnd_start_xmit() - Transmit NDO callback
>+ * @skb: Socket buffer ("packet") being sent from network stack
>+ * @dev: Virtual Network Device
>+ *
>+ * Standard network driver operations hook to transmit packets on virtual
>+ * network device. Called by network stack. Packet is not transmitted directly
>+ * from here; instead it is given to the rmnet egress handler.
>+ */
>+static netdev_tx_t rmnet_vnd_start_xmit(struct sk_buff *skb,
>+ struct net_device *dev)
>+{
>+ struct rmnet_vnd_private_s *dev_conf;
>+
>+ dev_conf = (struct rmnet_vnd_private_s *)netdev_priv(dev);
>+ if (dev_conf->local_ep.egress_dev) {
>+ rmnet_egress_handler(skb, &dev_conf->local_ep);
>+ } else {
>+ dev->stats.tx_dropped++;
>+ rmnet_kfree_skb(skb, RMNET_STATS_SKBFREE_VND_NO_EGRESS);
>+ }
>+ return NETDEV_TX_OK;
>+}
>+
>+/* rmnet_vnd_change_mtu() - Change MTU NDO callback
>+ * @dev: Virtual network device
>+ * @new_mtu: New MTU value to set (in bytes)
>+ *
>+ * Standard network driver operations hook to set the MTU. Called by kernel to
>+ * set the device MTU. Checks if desired MTU is less than zero or greater than
>+ * RMNET_MAX_PACKET_SIZE;
>+ */
>+static int rmnet_vnd_change_mtu(struct net_device *dev, int new_mtu)
>+{
>+ if (new_mtu < 0 || new_mtu > RMNET_MAX_PACKET_SIZE)
>+ return -EINVAL;
>+
>+ dev->mtu = new_mtu;
>+ return 0;
>+}
>+
>+static const struct net_device_ops rmnet_vnd_ops = {
>+ .ndo_init = 0,
>+ .ndo_start_xmit = rmnet_vnd_start_xmit,
>+ .ndo_change_mtu = rmnet_vnd_change_mtu,
>+ .ndo_set_mac_address = 0,
>+ .ndo_validate_addr = 0,
These are NULL by default. No need to init.
>+};
>+
>+static void rmnet_vnd_free(struct net_device *dev)
>+{
>+ free_netdev(dev);
>+}
>+
>+/* rmnet_vnd_setup() - net_device initialization callback
>+ * @dev: Virtual network device
>+ *
>+ * Called by kernel whenever a new rmnet<n> device is created. Sets MTU,
>+ * flags, ARP type, needed headroom, etc...
>+ */
>+void rmnet_vnd_setup(struct net_device *dev)
>+{
>+ struct rmnet_vnd_private_s *dev_conf;
>+
>+ LOGM("Setting up device %s", dev->name);
>+
>+ /* Clear out private data */
>+ dev_conf = (struct rmnet_vnd_private_s *)netdev_priv(dev);
>+ memset(dev_conf, 0, sizeof(struct rmnet_vnd_private_s));
>+
>+ dev->netdev_ops = &rmnet_vnd_ops;
>+ dev->mtu = RMNET_DFLT_PACKET_SIZE;
>+ dev->needed_headroom = RMNET_NEEDED_HEADROOM;
>+ random_ether_addr(dev->dev_addr);
>+ dev->tx_queue_len = RMNET_TX_QUEUE_LEN;
>+
>+ /* Raw IP mode */
>+ dev->header_ops = 0; /* No header */
>+ dev->type = ARPHRD_RAWIP;
>+ dev->hard_header_len = 0;
>+ dev->flags &= ~(IFF_BROADCAST | IFF_MULTICAST);
>+
>+ dev->destructor = rmnet_vnd_free;
>+}
>+
>+/* Exposed API */
>+
>+/* rmnet_vnd_exit() - Shutdown cleanup hook
>+ *
>+ * Called by RmNet main on module unload. Cleans up data structures and
>+ * unregisters/frees net_devices.
>+ */
>+void rmnet_vnd_exit(void)
>+{
>+ int i;
>+
>+ for (i = 0; i < RMNET_MAX_VND; i++)
>+ if (rmnet_devices[i]) {
>+ unregister_netdev(rmnet_devices[i]);
>+ free_netdev(rmnet_devices[i]);
>+ }
>+}
>+
>+/* rmnet_vnd_init() - Init hook
>+ *
>+ * Called by RmNet main on module load. Initializes data structures
>+ */
>+int rmnet_vnd_init(void)
>+{
>+ memset(rmnet_devices, 0, sizeof(struct net_device *) * RMNET_MAX_VND);
>+ return 0;
>+}
>+
>+/* rmnet_vnd_create_dev() - Create a new virtual network device node.
>+ * @id: Virtual device node id
>+ * @new_device: Pointer to newly created device node
>+ * @prefix: Device name prefix
>+ *
>+ * Allocates structures for new virtual network devices. Sets the name of the
>+ * new device and registers it with the network stack. Device will appear in
>+ * ifconfig list after this is called. If the prefix is null, then
>+ * RMNET_DEV_NAME_STR will be assumed.
>+ */
>+int rmnet_vnd_newlink(int id, struct net_device *new_device)
>+{
>+ int rc;
>+
>+ if (rmnet_devices[id])
>+ return -EINVAL;
>+
>+ rc = register_netdevice(new_device);
>+ if (!rc) {
>+ rmnet_devices[id] = new_device;
>+ new_device->rtnl_link_ops = &rmnet_link_ops;
>+ }
>+
>+ return rc;
>+}
>+
>+/* rmnet_vnd_free_dev() - free a virtual network device node.
>+ * @id: Virtual device node id
>+ *
>+ * Unregisters the virtual network device node and frees it.
>+ * unregister_netdev locks the rtnl mutex, so the mutex must not be locked
>+ * by the caller of the function. unregister_netdev enqueues the request to
>+ * unregister the device into a TODO queue. The requests in the TODO queue
>+ * are only done after rtnl mutex is unlocked, therefore free_netdev has to
>+ * called after unlocking rtnl mutex.
>+ */
>+int rmnet_vnd_free_dev(int id)
>+{
>+ struct rmnet_logical_ep_conf_s *epconfig_l;
>+ struct net_device *dev;
>+
>+ rtnl_lock();
>+ if ((id < 0) || (id >= RMNET_MAX_VND) || !rmnet_devices[id]) {
>+ rtnl_unlock();
>+ LOGM("Invalid id [%d]", id);
>+ return -EINVAL;
>+ }
>+
>+ epconfig_l = rmnet_vnd_get_le_config(rmnet_devices[id]);
>+ if (epconfig_l && epconfig_l->refcount) {
>+ rtnl_unlock();
>+ return -EINVAL;
>+ }
>+
>+ dev = rmnet_devices[id];
>+ rmnet_devices[id] = 0;
>+ rtnl_unlock();
>+
>+ if (dev) {
>+ unregister_netdev(dev);
>+ free_netdev(dev);
>+ return 0;
>+ } else {
>+ return -EINVAL;
>+ }
>+}
>+
>+int rmnet_vnd_remove_ref_dev(int id)
>+{
>+ struct rmnet_logical_ep_conf_s *epconfig_l;
>+
>+ if ((id < 0) || (id >= RMNET_MAX_VND) || !rmnet_devices[id])
Unneeded inner "()"s. I see you have it on multiple places.
>+ return -EINVAL;
>+
>+ epconfig_l = rmnet_vnd_get_le_config(rmnet_devices[id]);
>+ if (epconfig_l && epconfig_l->refcount)
>+ return -EBUSY;
>+
>+ rmnet_devices[id] = 0;
>+ return 0;
>+}
>+
>+/* rmnet_vnd_is_vnd() - Determine if net_device is RmNet owned virtual devices
>+ * @dev: Network device to test
>+ *
>+ * Searches through list of known RmNet virtual devices. This function is O(n)
>+ * and should not be used in the data path.
>+ *
>+ * To get the read id, subtract this result by 1.
>+ */
>+int rmnet_vnd_is_vnd(struct net_device *dev)
>+{
>+ /* This is not an efficient search, but, this will only be called in
>+ * a configuration context, and the list is small.
>+ */
>+ int i;
>+
>+ if (!dev)
>+ return 0;
>+
>+ for (i = 0; i < RMNET_MAX_VND; i++)
>+ if (dev == rmnet_devices[i])
>+ return i + 1;
>+
>+ return 0;
>+}
>+
>+/* rmnet_vnd_get_le_config() - Get the logical endpoint configuration
>+ * @dev: Virtual device node
>+ *
>+ * Gets the logical endpoint configuration for a RmNet virtual network device
>+ * node. Caller should confirm that devices is a RmNet VND before calling.
>+ */
>+struct rmnet_logical_ep_conf_s *rmnet_vnd_get_le_config(struct net_device *dev)
>+{
>+ struct rmnet_vnd_private_s *dev_conf;
>+
>+ if (!dev)
>+ return 0;
>+
>+ dev_conf = (struct rmnet_vnd_private_s *)netdev_priv(dev);
The typecast is not needed since netdev_priv is void*. You have it all
over the code.
>+ if (!dev_conf)
>+ return 0;
>+
>+ return &dev_conf->local_ep;
>+}
>+
>+/* rmnet_vnd_do_flow_control() - Process flow control request
>+ * @dev: Virtual network device node to do lookup on
>+ * @enable: boolean to enable/disable flow.
>+ */
>+int rmnet_vnd_do_flow_control(struct net_device *dev, int enable)
>+{
>+ struct rmnet_vnd_private_s *dev_conf;
>+
>+ if (unlikely(!dev) || !rmnet_vnd_is_vnd(dev))
>+ return -EINVAL;
>+
>+ dev_conf = (struct rmnet_vnd_private_s *)netdev_priv(dev);
>+ if (unlikely(!dev_conf))
>+ return -EINVAL;
>+
>+ LOGD("Setting VND TX queue state to %d", enable);
>+ /* Although we expect similar number of enable/disable
>+ * commands, optimize for the disable. That is more
>+ * latency sensitive than enable
>+ */
>+ if (unlikely(enable))
>+ netif_wake_queue(dev);
>+ else
>+ netif_stop_queue(dev);
>+
>+ return 0;
>+}
>+
>+/* rmnet_vnd_get_by_id() - Get VND by array index ID
>+ * @id: Virtual network deice id [0:RMNET_MAX_VND]
>+ */
>+struct net_device *rmnet_vnd_get_by_id(int id)
>+{
>+ if (id < 0 || id >= RMNET_MAX_VND)
>+ return 0;
>+
>+ return rmnet_devices[id];
>+}
>diff --git a/drivers/net/rmnet/rmnet_vnd.h b/drivers/net/rmnet/rmnet_vnd.h
>new file mode 100644
>index 0000000..8095e91
>--- /dev/null
>+++ b/drivers/net/rmnet/rmnet_vnd.h
>@@ -0,0 +1,34 @@
>+/* Copyright (c) 2013-2017, The Linux Foundation. All rights reserved.
>+ *
>+ * This program is free software; you can redistribute it and/or modify
>+ * it under the terms of the GNU General Public License version 2 and
>+ * only version 2 as published by the Free Software Foundation.
>+ *
>+ * This program is distributed in the hope that it will be useful,
>+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
>+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>+ * GNU General Public License for more details.
>+ *
>+ * RMNET Data Virtual Network Device APIs
>+ *
>+ */
>+
>+#include <linux/types.h>
>+
>+#ifndef _RMNET_VND_H_
>+#define _RMNET_VND_H_
>+
>+int rmnet_vnd_do_flow_control(struct net_device *dev, int enable);
>+struct rmnet_logical_ep_conf_s *rmnet_vnd_get_le_config(struct net_device *dev);
>+int rmnet_vnd_free_dev(int id);
>+int rmnet_vnd_remove_ref_dev(int id);
>+int rmnet_vnd_rx_fixup(struct sk_buff *skb, struct net_device *dev);
>+int rmnet_vnd_tx_fixup(struct sk_buff *skb, struct net_device *dev);
>+int rmnet_vnd_is_vnd(struct net_device *dev);
>+int rmnet_vnd_init(void);
>+void rmnet_vnd_exit(void);
>+struct net_device *rmnet_vnd_get_by_id(int id);
>+void rmnet_vnd_setup(struct net_device *dev);
>+int rmnet_vnd_newlink(int id, struct net_device *new_device);
>+
>+#endif /* _RMNET_VND_H_ */
>diff --git a/include/uapi/linux/Kbuild b/include/uapi/linux/Kbuild
>index dd9820b..ec29d61 100644
>--- a/include/uapi/linux/Kbuild
>+++ b/include/uapi/linux/Kbuild
>@@ -370,6 +370,7 @@ header-y += resource.h
> header-y += rfkill.h
> header-y += rio_cm_cdev.h
> header-y += rio_mport_cdev.h
>+header-y += rmnet.h
> header-y += romfs_fs.h
> header-y += rose.h
> header-y += route.h
>diff --git a/include/uapi/linux/if_arp.h b/include/uapi/linux/if_arp.h
>index 4d024d7..e762447 100644
>--- a/include/uapi/linux/if_arp.h
>+++ b/include/uapi/linux/if_arp.h
>@@ -59,6 +59,7 @@
> #define ARPHRD_LAPB 516 /* LAPB */
> #define ARPHRD_DDCMP 517 /* Digital's DDCMP protocol */
> #define ARPHRD_RAWHDLC 518 /* Raw HDLC */
>+#define ARPHRD_RAWIP 530 /* Raw IP */
>
> #define ARPHRD_TUNNEL 768 /* IPIP tunnel */
> #define ARPHRD_TUNNEL6 769 /* IP6IP6 tunnel */
>diff --git a/include/uapi/linux/if_ether.h b/include/uapi/linux/if_ether.h
>index 5bc9bfd..70520da 100644
>--- a/include/uapi/linux/if_ether.h
>+++ b/include/uapi/linux/if_ether.h
>@@ -104,7 +104,9 @@
> #define ETH_P_QINQ3 0x9300 /* deprecated QinQ VLAN [ NOT AN OFFICIALLY REGISTERED ID ] */
> #define ETH_P_EDSA 0xDADA /* Ethertype DSA [ NOT AN OFFICIALLY REGISTERED ID ] */
> #define ETH_P_AF_IUCV 0xFBFB /* IBM af_iucv [ NOT AN OFFICIALLY REGISTERED ID ] */
>-
>+#define ETH_P_MAP 0xDA1A /* Multiplexing and Aggregation Protocol
>+ * NOT AN OFFICIALLY REGISTERED ID ]
Please push this and ARPHRD_RAWIP as separate patches, to increase the
visibility.
>+ */
> #define ETH_P_802_3_MIN 0x0600 /* If the value in the ethernet type is less than this value
> * then the frame is Ethernet II. Else it is 802.3 */
>
>diff --git a/include/uapi/linux/rmnet.h b/include/uapi/linux/rmnet.h
>new file mode 100644
>index 0000000..dce5763
>--- /dev/null
>+++ b/include/uapi/linux/rmnet.h
>@@ -0,0 +1,34 @@
>+#ifndef _RMNET_DATA_H_
>+#define _RMNET_DATA_H_
>+
>+/* Constants */
>+#define RMNET_EGRESS_FORMAT__RESERVED__ (1<<0)
>+#define RMNET_EGRESS_FORMAT_MAP (1<<1)
>+#define RMNET_EGRESS_FORMAT_AGGREGATION (1<<2)
>+#define RMNET_EGRESS_FORMAT_MUXING (1<<3)
>+#define RMNET_EGRESS_FORMAT_MAP_CKSUMV3 (1<<4)
>+#define RMNET_EGRESS_FORMAT_MAP_CKSUMV4 (1<<5)
>+
>+#define RMNET_INGRESS_FIX_ETHERNET (1<<0)
>+#define RMNET_INGRESS_FORMAT_MAP (1<<1)
>+#define RMNET_INGRESS_FORMAT_DEAGGREGATION (1<<2)
>+#define RMNET_INGRESS_FORMAT_DEMUXING (1<<3)
>+#define RMNET_INGRESS_FORMAT_MAP_COMMANDS (1<<4)
>+#define RMNET_INGRESS_FORMAT_MAP_CKSUMV3 (1<<5)
>+#define RMNET_INGRESS_FORMAT_MAP_CKSUMV4 (1<<6)
>+
>+/* Pass the frame up the stack with no modifications to skb->dev */
>+#define RMNET_EPMODE_NONE (0)
>+/* Replace skb->dev to a virtual rmnet device and pass up the stack */
>+#define RMNET_EPMODE_VND (1)
>+/* Pass the frame directly to another device with dev_queue_xmit() */
>+#define RMNET_EPMODE_BRIDGE (2)
>+
>+enum {
>+ IFLA_RMNET_UNSPEC,
>+ IFLA_RMNET_MUX_ID,
>+ __IFLA_RMNET_MAX,
>+};
This belongs to include/uapi/linux/if_link.h
Please see IFLA_BOND_* as example
>+#define __IFLA_RMNET_MAX (__IFLA_RMNET_MAX - 1)
>+
>+#endif /* _RMNET_DATA_H_ */
>--
>1.9.1
>
Powered by blists - more mailing lists