Message-ID: <20180312210812.GB17283@nanopsycho>
Date:   Mon, 12 Mar 2018 22:08:12 +0100
From:   Jiri Pirko <jiri@...nulli.us>
To:     "Samudrala, Sridhar" <sridhar.samudrala@...el.com>
Cc:     mst@...hat.com, stephen@...workplumber.org, davem@...emloft.net,
        netdev@...r.kernel.org, virtio-dev@...ts.oasis-open.org,
        jesse.brandeburg@...el.com, alexander.h.duyck@...el.com,
        kubakici@...pl
Subject: Re: [PATCH v4 2/2] virtio_net: Extend virtio to use VF datapath when
 available

Mon, Mar 12, 2018 at 09:58:06PM CET, sridhar.samudrala@...el.com wrote:
>
>
>On 3/12/2018 1:12 PM, Jiri Pirko wrote:
>> Thu, Mar 01, 2018 at 09:08:43PM CET, sridhar.samudrala@...el.com wrote:
>> > This patch enables virtio_net to switch over to a VF datapath when a VF
>> > netdev is present with the same MAC address. It allows live migration
>> > of a VM with a direct attached VF without the need to setup a bond/team
>> > between a VF and virtio net device in the guest.
>> > 
>> > The hypervisor needs to enable only one datapath at any time so that
>> > packets don't get looped back to the VM over the other datapath. When a VF
>> > is plugged, the virtio datapath link state can be marked as down. The
>> > hypervisor needs to unplug the VF device from the guest on the source host
>> > and reset the MAC filter of the VF to initiate failover of datapath to
>> > virtio before starting the migration. After the migration is completed,
>> > the destination hypervisor sets the MAC filter on the VF and plugs it back
>> > to the guest to switch over to VF datapath.
>> > 
>> > When BACKUP feature is enabled, an additional netdev(bypass netdev) is
>> > created that acts as a master device and tracks the state of the 2 lower
>> > netdevs. The original virtio_net netdev is marked as 'backup' netdev and a
>> > passthru device with the same MAC is registered as 'active' netdev.
>> > 
>> > This patch is based on the discussion initiated by Jesse on this thread.
>> > https://marc.info/?l=linux-virtualization&m=151189725224231&w=2
>> > 
>> > Signed-off-by: Sridhar Samudrala <sridhar.samudrala@...el.com>
>> > Signed-off-by: Alexander Duyck <alexander.h.duyck@...el.com>
>> > Reviewed-by: Jesse Brandeburg <jesse.brandeburg@...el.com>
>> [...]
>> 
>> 
>> > +static int virtnet_bypass_register_child(struct net_device *child_netdev)
>> > +{
>> > +	struct virtnet_bypass_info *vbi;
>> > +	struct net_device *dev;
>> > +	bool backup;
>> > +	int ret;
>> > +
>> > +	if (child_netdev->addr_len != ETH_ALEN)
>> > +		return NOTIFY_DONE;
>> > +
>> > +	/* We will use the MAC address to locate the virtnet_bypass netdev
>> > +	 * to associate with the child netdev. If we don't find a matching
>> > +	 * bypass netdev, move on.
>> > +	 */
>> > +	dev = get_virtnet_bypass_bymac(dev_net(child_netdev),
>> > +				       child_netdev->perm_addr);
>> > +	if (!dev)
>> > +		return NOTIFY_DONE;
>> > +
>> > +	vbi = netdev_priv(dev);
>> > +	backup = (child_netdev->dev.parent == dev->dev.parent);
>> > +	if (backup ? rtnl_dereference(vbi->backup_netdev) :
>> > +			rtnl_dereference(vbi->active_netdev)) {
>> > +		netdev_info(dev,
>> > +			    "%s attempting to join bypass dev when %s already present\n",
>> > +			    child_netdev->name, backup ? "backup" : "active");
>> > +		return NOTIFY_DONE;
>> > +	}
>> > +
>> > +	/* Avoid non pci devices as active netdev */
>> > +	if (!backup && (!child_netdev->dev.parent ||
>> > +			!dev_is_pci(child_netdev->dev.parent)))
>> > +		return NOTIFY_DONE;
>> > +
>> > +	ret = netdev_rx_handler_register(child_netdev,
>> > +					 virtnet_bypass_handle_frame, dev);
>> > +	if (ret != 0) {
>> > +		netdev_err(child_netdev,
>> > +			   "can not register bypass receive handler (err = %d)\n",
>> > +			   ret);
>> > +		goto rx_handler_failed;
>> > +	}
>> > +
>> > +	ret = netdev_upper_dev_link(child_netdev, dev, NULL);
>> > +	if (ret != 0) {
>> > +		netdev_err(child_netdev,
>> > +			   "can not set master device %s (err = %d)\n",
>> > +			   dev->name, ret);
>> > +		goto upper_link_failed;
>> > +	}
>> > +
>> > +	child_netdev->flags |= IFF_SLAVE;
>> > +
>> > +	if (netif_running(dev)) {
>> > +		ret = dev_open(child_netdev);
>> > +		if (ret && (ret != -EBUSY)) {
>> > +			netdev_err(dev, "Opening child %s failed ret:%d\n",
>> > +				   child_netdev->name, ret);
>> > +			goto err_interface_up;
>> > +		}
>> > +	}
>> Much of this function is copy of netvsc_vf_join, should be shared with
>> netvsc.
>
>Yes. This is based on netvsc_register_vf() and netvsc_vf_join(). But modified
>to handle registration of 2 child netdevs(backup virtio and active vf).  In case
>of netvsc, they only register VF. There is no backup netdev.
>I think trying to make this code shareable with netvsc will introduce additional
>checks and make it convoluted.

No problem.


>
>
>> 
>> 
>> > +
>> > +	/* Align MTU of child with master */
>> > +	ret = dev_set_mtu(child_netdev, dev->mtu);
>> > +	if (ret) {
>> > +		netdev_err(dev,
>> > +			   "unable to change mtu of %s to %u register failed\n",
>> > +			   child_netdev->name, dev->mtu);
>> > +		goto err_set_mtu;
>> > +	}
>> > +
>> > +	call_netdevice_notifiers(NETDEV_JOIN, child_netdev);
>> > +
>> > +	netdev_info(dev, "registering %s\n", child_netdev->name);
>> > +
>> > +	dev_hold(child_netdev);
>> > +	if (backup) {
>> > +		rcu_assign_pointer(vbi->backup_netdev, child_netdev);
>> > +		dev_get_stats(vbi->backup_netdev, &vbi->backup_stats);
>> > +	} else {
>> > +		rcu_assign_pointer(vbi->active_netdev, child_netdev);
>> > +		dev_get_stats(vbi->active_netdev, &vbi->active_stats);
>> > +		dev->min_mtu = child_netdev->min_mtu;
>> > +		dev->max_mtu = child_netdev->max_mtu;
>> > +	}
>> > +
>> > +	return NOTIFY_OK;
>> > +
>> > +err_set_mtu:
>> > +	dev_close(child_netdev);
>> > +err_interface_up:
>> > +	netdev_upper_dev_unlink(child_netdev, dev);
>> > +	child_netdev->flags &= ~IFF_SLAVE;
>> > +upper_link_failed:
>> > +	netdev_rx_handler_unregister(child_netdev);
>> > +rx_handler_failed:
>> > +	return NOTIFY_DONE;
>> > +}
>> > +
>> > +static int virtnet_bypass_unregister_child(struct net_device *child_netdev)
>> > +{
>> > +	struct virtnet_bypass_info *vbi;
>> > +	struct net_device *dev, *backup;
>> > +
>> > +	dev = get_virtnet_bypass_byref(child_netdev);
>> > +	if (!dev)
>> > +		return NOTIFY_DONE;
>> > +
>> > +	vbi = netdev_priv(dev);
>> > +
>> > +	netdev_info(dev, "unregistering %s\n", child_netdev->name);
>> > +
>> > +	netdev_rx_handler_unregister(child_netdev);
>> > +	netdev_upper_dev_unlink(child_netdev, dev);
>> > +	child_netdev->flags &= ~IFF_SLAVE;
>> > +
>> > +	if (child_netdev->dev.parent == dev->dev.parent) {
>> > +		RCU_INIT_POINTER(vbi->backup_netdev, NULL);
>> > +	} else {
>> > +		RCU_INIT_POINTER(vbi->active_netdev, NULL);
>> > +		backup = rtnl_dereference(vbi->backup_netdev);
>> > +		if (backup) {
>> > +			dev->min_mtu = backup->min_mtu;
>> > +			dev->max_mtu = backup->max_mtu;
>> > +		}
>> > +	}
>> > +
>> > +	dev_put(child_netdev);
>> > +
>> > +	return NOTIFY_OK;
>> > +}
>> > +
>> > +static int virtnet_bypass_update_link(struct net_device *child_netdev)
>> > +{
>> > +	struct net_device *dev, *active, *backup;
>> > +	struct virtnet_bypass_info *vbi;
>> > +
>> > +	dev = get_virtnet_bypass_byref(child_netdev);
>> > +	if (!dev || !netif_running(dev))
>> > +		return NOTIFY_DONE;
>> > +
>> > +	vbi = netdev_priv(dev);
>> > +
>> > +	active = rtnl_dereference(vbi->active_netdev);
>> > +	backup = rtnl_dereference(vbi->backup_netdev);
>> > +
>> > +	if ((active && virtnet_bypass_xmit_ready(active)) ||
>> > +	    (backup && virtnet_bypass_xmit_ready(backup))) {
>> > +		netif_carrier_on(dev);
>> > +		netif_tx_wake_all_queues(dev);
>> > +	} else {
>> > +		netif_carrier_off(dev);
>> > +		netif_tx_stop_all_queues(dev);
>> > +	}
>> > +
>> > +	return NOTIFY_OK;
>> > +}
>> > +
>> > +static int virtnet_bypass_event(struct notifier_block *this,
>> > +				unsigned long event, void *ptr)
>> > +{
>> > +	struct net_device *event_dev = netdev_notifier_info_to_dev(ptr);
>> > +
>> > +	/* Skip our own events */
>> > +	if (event_dev->netdev_ops == &virtnet_bypass_netdev_ops)
>> > +		return NOTIFY_DONE;
>> > +
>> > +	/* Avoid non-Ethernet type devices */
>> > +	if (event_dev->type != ARPHRD_ETHER)
>> > +		return NOTIFY_DONE;
>> > +
>> > +	/* Avoid Vlan dev with same MAC registering as child dev */
>> > +	if (is_vlan_dev(event_dev))
>> > +		return NOTIFY_DONE;
>> > +
>> > +	/* Avoid Bonding master dev with same MAC registering as child dev */
>> > +	if ((event_dev->priv_flags & IFF_BONDING) &&
>> > +	    (event_dev->flags & IFF_MASTER))
>> > +		return NOTIFY_DONE;
>> > +
>> > +	switch (event) {
>> > +	case NETDEV_REGISTER:
>> > +		return virtnet_bypass_register_child(event_dev);
>> > +	case NETDEV_UNREGISTER:
>> > +		return virtnet_bypass_unregister_child(event_dev);
>> > +	case NETDEV_UP:
>> > +	case NETDEV_DOWN:
>> > +	case NETDEV_CHANGE:
>> > +		return virtnet_bypass_update_link(event_dev);
>> > +	default:
>> > +		return NOTIFY_DONE;
>> > +	}
>> > +}
>> For example this function is 1:1 copy of netvsc, even with comments
>> and bugs (like IFF_BODING check).
>> 
>> This is also something that should be shared with netvsc.
>
>The problem is with the calls that are made from this function.
>Sharing would have been possible if both virtio and netvsc went with
>same netdev model.

ops? You can still share.


>
>> 
>> 
>> > +
>> > +static struct notifier_block virtnet_bypass_notifier = {
>> > +	.notifier_call = virtnet_bypass_event,
>> > +};
>> > +
>> > +static int virtnet_bypass_create(struct virtnet_info *vi)
>> > +{
>> > +	struct net_device *backup_netdev = vi->dev;
>> > +	struct device *dev = &vi->vdev->dev;
>> > +	struct net_device *bypass_netdev;
>> > +	int res;
>> > +
>> > +	/* Alloc at least 2 queues, for now we are going with 16 assuming
>> > +	 * that most devices being bonded won't have too many queues.
>> > +	 */
>> > +	bypass_netdev = alloc_etherdev_mq(sizeof(struct virtnet_bypass_info),
>> > +					  16);
>> > +	if (!bypass_netdev) {
>> > +		dev_err(dev, "Unable to allocate bypass_netdev!\n");
>> > +		return -ENOMEM;
>> > +	}
>> > +
>> > +	dev_net_set(bypass_netdev, dev_net(backup_netdev));
>> > +	SET_NETDEV_DEV(bypass_netdev, dev);
>> > +
>> > +	bypass_netdev->netdev_ops = &virtnet_bypass_netdev_ops;
>> > +	bypass_netdev->ethtool_ops = &virtnet_bypass_ethtool_ops;
>> > +
>> > +	/* Initialize the device options */
>> > +	bypass_netdev->flags |= IFF_MASTER;
>> > +	bypass_netdev->priv_flags |= IFF_BONDING | IFF_UNICAST_FLT |
>> No clue why you set IFF_BONDING here...
>
>This is to indicate to the userspace that this is a master bond device.

This is not a master bond device! If you say this, it makes me really
worried....



>May be it is sufficient to just set IFF_MASTER.
>
>> 
>> 
>> 
>> 
>> 
>

Powered by blists - more mailing lists