| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Wed, 8 Aug 2018 09:04:33 +0100
From: Jose Abreu <Jose.Abreu@...opsys.com>
To: netdev@...r.kernel.org
Cc: Jose Abreu <Jose.Abreu@...opsys.com>,
"David S. Miller" <davem@...emloft.net>,
Joao Pinto <Joao.Pinto@...opsys.com>,
Giuseppe Cavallaro <peppe.cavallaro@...com>,
Alexandre Torgue <alexandre.torgue@...com>,
Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>
Subject: [PATCH v4 net-next 5/9] net: stmmac: Add MDIO related functions for XGMAC2
Add the MDIO related funcionalities for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@...opsys.com>
Cc: David S. Miller <davem@...emloft.net>
Cc: Joao Pinto <jpinto@...opsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@...com>
Cc: Alexandre Torgue <alexandre.torgue@...com>
Cc: Andrew Lunn <andrew@...n.ch>
Cc: Florian Fainelli <f.fainelli@...il.com>
---
Changes from v3:
- Check if unsupported phy_addr was specified in DT
- Clear C22 reg before setting the bit (Florian)
- Limit the number of possible phys to 4 (for now) (Florian)
Changes from v2:
- Use helper to set C22 (Andrew)
- Wait for bus free before setting C22 reg (Andrew)
Changes from v1:
- Remove C45 support (Andrew)
- Add define for bits (Andrew)
- Remove uneeded cast (Andrew)
- Use different callbacks instead of if's (Andrew)
---
drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 133 +++++++++++++++++++++-
1 file changed, 129 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index 5df1a608e566..b72ef171477e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -29,6 +29,7 @@
#include <linux/phy.h>
#include <linux/slab.h>
+#include "dwxgmac2.h"
#include "stmmac.h"
#define MII_BUSY 0x00000001
@@ -39,6 +40,115 @@
#define MII_GMAC4_WRITE (1 << MII_GMAC4_GOC_SHIFT)
#define MII_GMAC4_READ (3 << MII_GMAC4_GOC_SHIFT)
+/* XGMAC defines */
+#define MII_XGMAC_SADDR BIT(18)
+#define MII_XGMAC_CMD_SHIFT 16
+#define MII_XGMAC_WRITE (1 << MII_XGMAC_CMD_SHIFT)
+#define MII_XGMAC_READ (3 << MII_XGMAC_CMD_SHIFT)
+#define MII_XGMAC_BUSY BIT(22)
+#define MII_XGMAC_MAX_C22ADDR 3
+#define MII_XGMAC_C22P_MASK GENMASK(MII_XGMAC_MAX_C22ADDR, 0)
+
+static int stmmac_xgmac2_c22_format(struct stmmac_priv *priv, int phyaddr,
+ int phyreg, u32 *hw_addr)
+{
+ unsigned int mii_data = priv->hw->mii.data;
+ u32 tmp;
+
+ /* HW does not support C22 addr >= 4 */
+ if (phyaddr > MII_XGMAC_MAX_C22ADDR)
+ return -ENODEV;
+ /* Wait until any existing MII operation is complete */
+ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
+ !(tmp & MII_XGMAC_BUSY), 100, 10000))
+ return -EBUSY;
+
+ /* Set port as Clause 22 */
+ tmp = readl(priv->ioaddr + XGMAC_MDIO_C22P);
+ tmp &= ~MII_XGMAC_C22P_MASK;
+ tmp |= BIT(phyaddr);
+ writel(tmp, priv->ioaddr + XGMAC_MDIO_C22P);
+
+ *hw_addr = (phyaddr << 16) | (phyreg & 0x1f);
+ return 0;
+}
+
+static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
+{
+ struct net_device *ndev = bus->priv;
+ struct stmmac_priv *priv = netdev_priv(ndev);
+ unsigned int mii_address = priv->hw->mii.addr;
+ unsigned int mii_data = priv->hw->mii.data;
+ u32 tmp, addr, value = MII_XGMAC_BUSY;
+ int ret;
+
+ if (phyreg & MII_ADDR_C45) {
+ return -EOPNOTSUPP;
+ } else {
+ ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
+ if (ret)
+ return ret;
+ }
+
+ value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
+ & priv->hw->mii.clk_csr_mask;
+ value |= MII_XGMAC_SADDR | MII_XGMAC_READ;
+
+ /* Wait until any existing MII operation is complete */
+ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
+ !(tmp & MII_XGMAC_BUSY), 100, 10000))
+ return -EBUSY;
+
+ /* Set the MII address register to read */
+ writel(addr, priv->ioaddr + mii_address);
+ writel(value, priv->ioaddr + mii_data);
+
+ /* Wait until any existing MII operation is complete */
+ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
+ !(tmp & MII_XGMAC_BUSY), 100, 10000))
+ return -EBUSY;
+
+ /* Read the data from the MII data register */
+ return readl(priv->ioaddr + mii_data) & GENMASK(15, 0);
+}
+
+static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr,
+ int phyreg, u16 phydata)
+{
+ struct net_device *ndev = bus->priv;
+ struct stmmac_priv *priv = netdev_priv(ndev);
+ unsigned int mii_address = priv->hw->mii.addr;
+ unsigned int mii_data = priv->hw->mii.data;
+ u32 addr, tmp, value = MII_XGMAC_BUSY;
+ int ret;
+
+ if (phyreg & MII_ADDR_C45) {
+ return -EOPNOTSUPP;
+ } else {
+ ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
+ if (ret)
+ return ret;
+ }
+
+ value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
+ & priv->hw->mii.clk_csr_mask;
+ value |= phydata | MII_XGMAC_SADDR;
+ value |= MII_XGMAC_WRITE;
+
+ /* Wait until any existing MII operation is complete */
+ if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
+ !(tmp & MII_XGMAC_BUSY), 100, 10000))
+ return -EBUSY;
+
+ /* Set the MII address register to write */
+ writel(addr, priv->ioaddr + mii_address);
+ writel(value, priv->ioaddr + mii_data);
+
+ /* Wait until any existing MII operation is complete */
+ return readl_poll_timeout(priv->ioaddr + mii_data, tmp,
+ !(tmp & MII_XGMAC_BUSY), 100, 10000);
+}
+
/**
* stmmac_mdio_read
* @bus: points to the mii_bus structure
@@ -205,7 +315,7 @@ int stmmac_mdio_register(struct net_device *ndev)
struct stmmac_mdio_bus_data *mdio_bus_data = priv->plat->mdio_bus_data;
struct device_node *mdio_node = priv->plat->mdio_node;
struct device *dev = ndev->dev.parent;
- int addr, found;
+ int addr, found, max_addr;
if (!mdio_bus_data)
return 0;
@@ -223,8 +333,23 @@ int stmmac_mdio_register(struct net_device *ndev)
#endif
new_bus->name = "stmmac";
- new_bus->read = &stmmac_mdio_read;
- new_bus->write = &stmmac_mdio_write;
+
+ if (priv->plat->has_xgmac) {
+ new_bus->read = &stmmac_xgmac2_mdio_read;
+ new_bus->write = &stmmac_xgmac2_mdio_write;
+
+ /* Right now only C22 phys are supported */
+ max_addr = MII_XGMAC_MAX_C22ADDR + 1;
+
+ /* Check if DT specified an unsupported phy addr */
+ if (priv->plat->phy_addr > MII_XGMAC_MAX_C22ADDR)
+ dev_err(dev, "Unsupported phy_addr (max=%d)\n",
+ MII_XGMAC_MAX_C22ADDR);
+ } else {
+ new_bus->read = &stmmac_mdio_read;
+ new_bus->write = &stmmac_mdio_write;
+ max_addr = PHY_MAX_ADDR;
+ }
new_bus->reset = &stmmac_mdio_reset;
snprintf(new_bus->id, MII_BUS_ID_SIZE, "%s-%x",
@@ -243,7 +368,7 @@ int stmmac_mdio_register(struct net_device *ndev)
goto bus_register_done;
found = 0;
- for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
+ for (addr = 0; addr < max_addr; addr++) {
struct phy_device *phydev = mdiobus_get_phy(new_bus, addr);
if (!phydev)
--
2.7.4
Powered by blists - more mailing lists