| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20181017222322.2171-11-jeffrey.t.kirsher@intel.com>
Date: Wed, 17 Oct 2018 15:23:21 -0700
From: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
To: davem@...emloft.net
Cc: Sasha Neftin <sasha.neftin@...el.com>, netdev@...r.kernel.org,
nhorman@...hat.com, sassmann@...hat.com,
Jeff Kirsher <jeffrey.t.kirsher@...el.com>
Subject: [net-next 10/11] igc: Add setup link functionality
From: Sasha Neftin <sasha.neftin@...el.com>
Add link establishment methods
Add auto negotiation methods
Add read MAC address method
Signed-off-by: Sasha Neftin <sasha.neftin@...el.com>
Tested-by: Aaron Brown <aaron.f.brown@...el.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@...el.com>
---
drivers/net/ethernet/intel/igc/igc.h | 1 +
drivers/net/ethernet/intel/igc/igc_base.c | 40 +++
drivers/net/ethernet/intel/igc/igc_defines.h | 38 +++
drivers/net/ethernet/intel/igc/igc_mac.c | 271 +++++++++++++++
drivers/net/ethernet/intel/igc/igc_mac.h | 2 +
drivers/net/ethernet/intel/igc/igc_main.c | 30 ++
drivers/net/ethernet/intel/igc/igc_phy.c | 334 +++++++++++++++++++
drivers/net/ethernet/intel/igc/igc_phy.h | 1 +
8 files changed, 717 insertions(+)
diff --git a/drivers/net/ethernet/intel/igc/igc.h b/drivers/net/ethernet/intel/igc/igc.h
index 7cfbd83d25e4..86fa889b4ab6 100644
--- a/drivers/net/ethernet/intel/igc/igc.h
+++ b/drivers/net/ethernet/intel/igc/igc.h
@@ -314,6 +314,7 @@ struct igc_adapter {
struct work_struct reset_task;
struct work_struct watchdog_task;
struct work_struct dma_err_task;
+ bool fc_autoneg;
u8 tx_timeout_factor;
diff --git a/drivers/net/ethernet/intel/igc/igc_base.c b/drivers/net/ethernet/intel/igc/igc_base.c
index 55faef987479..832da609d9a7 100644
--- a/drivers/net/ethernet/intel/igc/igc_base.c
+++ b/drivers/net/ethernet/intel/igc/igc_base.c
@@ -177,6 +177,29 @@ static s32 igc_init_nvm_params_base(struct igc_hw *hw)
return 0;
}
+/**
+ * igc_setup_copper_link_base - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Configures the link for auto-neg or forced speed and duplex. Then we check
+ * for link, once link is established calls to configure collision distance
+ * and flow control are called.
+ */
+static s32 igc_setup_copper_link_base(struct igc_hw *hw)
+{
+ s32 ret_val = 0;
+ u32 ctrl;
+
+ ctrl = rd32(IGC_CTRL);
+ ctrl |= IGC_CTRL_SLU;
+ ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX);
+ wr32(IGC_CTRL, ctrl);
+
+ ret_val = igc_setup_copper_link(hw);
+
+ return ret_val;
+}
+
/**
* igc_init_mac_params_base - Init MAC func ptrs.
* @hw: pointer to the HW structure
@@ -200,6 +223,9 @@ static s32 igc_init_mac_params_base(struct igc_hw *hw)
if (mac->type == igc_i225)
dev_spec->clear_semaphore_once = true;
+ /* physical interface link setup */
+ mac->ops.setup_physical_interface = igc_setup_copper_link_base;
+
return 0;
}
@@ -242,6 +268,8 @@ static s32 igc_init_phy_params_base(struct igc_hw *hw)
if (ret_val)
return ret_val;
+ igc_check_for_link_base(hw);
+
/* Verify phy id and set remaining function pointers */
switch (phy->id) {
case I225_I_PHY_ID:
@@ -258,10 +286,22 @@ static s32 igc_init_phy_params_base(struct igc_hw *hw)
static s32 igc_get_invariants_base(struct igc_hw *hw)
{
+ struct igc_mac_info *mac = &hw->mac;
u32 link_mode = 0;
u32 ctrl_ext = 0;
s32 ret_val = 0;
+ switch (hw->device_id) {
+ case IGC_DEV_ID_I225_LM:
+ case IGC_DEV_ID_I225_V:
+ mac->type = igc_i225;
+ break;
+ default:
+ return -IGC_ERR_MAC_INIT;
+ }
+
+ hw->phy.media_type = igc_media_type_copper;
+
ctrl_ext = rd32(IGC_CTRL_EXT);
link_mode = ctrl_ext & IGC_CTRL_EXT_LINK_MODE_MASK;
diff --git a/drivers/net/ethernet/intel/igc/igc_defines.h b/drivers/net/ethernet/intel/igc/igc_defines.h
index d271671e6825..70275a0e85d7 100644
--- a/drivers/net/ethernet/intel/igc/igc_defines.h
+++ b/drivers/net/ethernet/intel/igc/igc_defines.h
@@ -13,6 +13,11 @@
/* Physical Func Reset Done Indication */
#define IGC_CTRL_EXT_LINK_MODE_MASK 0x00C00000
+/* Loop limit on how long we wait for auto-negotiation to complete */
+#define COPPER_LINK_UP_LIMIT 10
+#define PHY_AUTO_NEG_LIMIT 45
+#define PHY_FORCE_LIMIT 20
+
/* Number of 100 microseconds we wait for PCI Express master disable */
#define MASTER_DISABLE_TIMEOUT 800
/*Blocks new Master requests */
@@ -54,6 +59,12 @@
#define IGC_CTRL_RST 0x04000000 /* Global reset */
#define IGC_CTRL_PHY_RST 0x80000000 /* PHY Reset */
+#define IGC_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
+#define IGC_CTRL_FRCSPD 0x00000800 /* Force Speed */
+#define IGC_CTRL_FRCDPX 0x00001000 /* Force Duplex */
+
+#define IGC_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
+#define IGC_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
/* PBA constants */
#define IGC_PBA_34K 0x0022
@@ -66,6 +77,29 @@
#define IGC_SWFW_EEP_SM 0x1
#define IGC_SWFW_PHY0_SM 0x2
+/* Autoneg Advertisement Register */
+#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
+#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
+#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
+#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
+#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
+#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
+
+/* Link Partner Ability Register (Base Page) */
+#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
+#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
+
+/* 1000BASE-T Control Register */
+#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */
+#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
+#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
+
+/* PHY GPY 211 registers */
+#define STANDARD_AN_REG_MASK 0x0007 /* MMD */
+#define ANEG_MULTIGBT_AN_CTRL 0x0020 /* MULTI GBT AN Control Register */
+#define MMD_DEVADDR_SHIFT 16 /* Shift MMD to higher bits */
+#define CR_2500T_FD_CAPS 0x0080 /* Advertise 2500T FD capability */
+
/* NVM Control */
/* Number of milliseconds for NVM auto read done after MAC reset. */
#define AUTO_READ_DONE_TIMEOUT 10
@@ -318,6 +352,10 @@
#define PHY_STATUS 0x01 /* Status Register */
#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
+#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
+#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
/* Bit definitions for valid PHY IDs. I = Integrated E = External */
#define I225_I_PHY_ID 0x67C9DC00
diff --git a/drivers/net/ethernet/intel/igc/igc_mac.c b/drivers/net/ethernet/intel/igc/igc_mac.c
index fce7f7f5aa46..f7683d3ae47c 100644
--- a/drivers/net/ethernet/intel/igc/igc_mac.c
+++ b/drivers/net/ethernet/intel/igc/igc_mac.c
@@ -92,6 +92,8 @@ s32 igc_setup_link(struct igc_hw *hw)
/* In the case of the phy reset being blocked, we already have a link.
* We do not need to set it up again.
*/
+ if (igc_check_reset_block(hw))
+ goto out;
/* If requested flow control is set to default, set flow control
* based on the EEPROM flow control settings.
@@ -142,9 +144,73 @@ s32 igc_setup_link(struct igc_hw *hw)
*/
static s32 igc_set_default_fc(struct igc_hw *hw)
{
+ hw->fc.requested_mode = igc_fc_full;
return 0;
}
+/**
+ * igc_force_mac_fc - Force the MAC's flow control settings
+ * @hw: pointer to the HW structure
+ *
+ * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the
+ * device control register to reflect the adapter settings. TFCE and RFCE
+ * need to be explicitly set by software when a copper PHY is used because
+ * autonegotiation is managed by the PHY rather than the MAC. Software must
+ * also configure these bits when link is forced on a fiber connection.
+ */
+s32 igc_force_mac_fc(struct igc_hw *hw)
+{
+ s32 ret_val = 0;
+ u32 ctrl;
+
+ ctrl = rd32(IGC_CTRL);
+
+ /* Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc.current_mode" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * frames but we do not receive pause frames).
+ * 3: Both Rx and TX flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
+ hw_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode);
+
+ switch (hw->fc.current_mode) {
+ case igc_fc_none:
+ ctrl &= (~(IGC_CTRL_TFCE | IGC_CTRL_RFCE));
+ break;
+ case igc_fc_rx_pause:
+ ctrl &= (~IGC_CTRL_TFCE);
+ ctrl |= IGC_CTRL_RFCE;
+ break;
+ case igc_fc_tx_pause:
+ ctrl &= (~IGC_CTRL_RFCE);
+ ctrl |= IGC_CTRL_TFCE;
+ break;
+ case igc_fc_full:
+ ctrl |= (IGC_CTRL_TFCE | IGC_CTRL_RFCE);
+ break;
+ default:
+ hw_dbg("Flow control param set incorrectly\n");
+ ret_val = -IGC_ERR_CONFIG;
+ goto out;
+ }
+
+ wr32(IGC_CTRL, ctrl);
+
+out:
+ return ret_val;
+}
+
/**
* igc_set_fc_watermarks - Set flow control high/low watermarks
* @hw: pointer to the HW structure
@@ -371,6 +437,7 @@ s32 igc_check_for_copper_link(struct igc_hw *hw)
* settings because we may have had to re-autoneg with a
* different link partner.
*/
+ ret_val = igc_config_fc_after_link_up(hw);
if (ret_val)
hw_dbg("Error configuring flow control\n");
@@ -399,6 +466,210 @@ void igc_config_collision_dist(struct igc_hw *hw)
wrfl();
}
+/**
+ * igc_config_fc_after_link_up - Configures flow control after link
+ * @hw: pointer to the HW structure
+ *
+ * Checks the status of auto-negotiation after link up to ensure that the
+ * speed and duplex were not forced. If the link needed to be forced, then
+ * flow control needs to be forced also. If auto-negotiation is enabled
+ * and did not fail, then we configure flow control based on our link
+ * partner.
+ */
+s32 igc_config_fc_after_link_up(struct igc_hw *hw)
+{
+ u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
+ struct igc_mac_info *mac = &hw->mac;
+ u16 speed, duplex;
+ s32 ret_val = 0;
+
+ /* Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if (mac->autoneg_failed) {
+ if (hw->phy.media_type == igc_media_type_copper)
+ ret_val = igc_force_mac_fc(hw);
+ }
+
+ if (ret_val) {
+ hw_dbg("Error forcing flow control settings\n");
+ goto out;
+ }
+
+ /* Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if (hw->phy.media_type == igc_media_type_copper && mac->autoneg) {
+ /* Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS,
+ &mii_status_reg);
+ if (ret_val)
+ goto out;
+ ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS,
+ &mii_status_reg);
+ if (ret_val)
+ goto out;
+
+ if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
+ hw_dbg("Copper PHY and Auto Neg has not completed.\n");
+ goto out;
+ }
+
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement
+ * Register (Address 4) and the Auto_Negotiation Base
+ * Page Ability Register (Address 5) to determine how
+ * flow control was negotiated.
+ */
+ ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV,
+ &mii_nway_adv_reg);
+ if (ret_val)
+ goto out;
+ ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY,
+ &mii_nway_lp_ability_reg);
+ if (ret_val)
+ goto out;
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | igc_fc_none
+ * 0 | 1 | 0 | DC | igc_fc_none
+ * 0 | 1 | 1 | 0 | igc_fc_none
+ * 0 | 1 | 1 | 1 | igc_fc_tx_pause
+ * 1 | 0 | 0 | DC | igc_fc_none
+ * 1 | DC | 1 | DC | igc_fc_full
+ * 1 | 1 | 0 | 0 | igc_fc_none
+ * 1 | 1 | 0 | 1 | igc_fc_rx_pause
+ *
+ * Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | IGC_fc_full
+ *
+ */
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /* Now we need to check if the user selected RX ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == igc_fc_full) {
+ hw->fc.current_mode = igc_fc_full;
+ hw_dbg("Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = igc_fc_rx_pause;
+ hw_dbg("Flow Control = RX PAUSE frames only.\n");
+ }
+ }
+
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | igc_fc_tx_pause
+ */
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.current_mode = igc_fc_tx_pause;
+ hw_dbg("Flow Control = TX PAUSE frames only.\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | igc_fc_rx_pause
+ */
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ hw->fc.current_mode = igc_fc_rx_pause;
+ hw_dbg("Flow Control = RX PAUSE frames only.\n");
+ }
+ /* Per the IEEE spec, at this point flow control should be
+ * disabled. However, we want to consider that we could
+ * be connected to a legacy switch that doesn't advertise
+ * desired flow control, but can be forced on the link
+ * partner. So if we advertised no flow control, that is
+ * what we will resolve to. If we advertised some kind of
+ * receive capability (Rx Pause Only or Full Flow Control)
+ * and the link partner advertised none, we will configure
+ * ourselves to enable Rx Flow Control only. We can do
+ * this safely for two reasons: If the link partner really
+ * didn't want flow control enabled, and we enable Rx, no
+ * harm done since we won't be receiving any PAUSE frames
+ * anyway. If the intent on the link partner was to have
+ * flow control enabled, then by us enabling RX only, we
+ * can at least receive pause frames and process them.
+ * This is a good idea because in most cases, since we are
+ * predominantly a server NIC, more times than not we will
+ * be asked to delay transmission of packets than asking
+ * our link partner to pause transmission of frames.
+ */
+ else if ((hw->fc.requested_mode == igc_fc_none) ||
+ (hw->fc.requested_mode == igc_fc_tx_pause) ||
+ (hw->fc.strict_ieee)) {
+ hw->fc.current_mode = igc_fc_none;
+ hw_dbg("Flow Control = NONE.\n");
+ } else {
+ hw->fc.current_mode = igc_fc_rx_pause;
+ hw_dbg("Flow Control = RX PAUSE frames only.\n");
+ }
+
+ /* Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val = hw->mac.ops.get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ hw_dbg("Error getting link speed and duplex\n");
+ goto out;
+ }
+
+ if (duplex == HALF_DUPLEX)
+ hw->fc.current_mode = igc_fc_none;
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = igc_force_mac_fc(hw);
+ if (ret_val) {
+ hw_dbg("Error forcing flow control settings\n");
+ goto out;
+ }
+ }
+
+out:
+ return 0;
+}
+
/**
* igc_get_auto_rd_done - Check for auto read completion
* @hw: pointer to the HW structure
diff --git a/drivers/net/ethernet/intel/igc/igc_mac.h b/drivers/net/ethernet/intel/igc/igc_mac.h
index c842cc561123..782bc995badc 100644
--- a/drivers/net/ethernet/intel/igc/igc_mac.h
+++ b/drivers/net/ethernet/intel/igc/igc_mac.h
@@ -15,6 +15,8 @@
/* forward declaration */
s32 igc_disable_pcie_master(struct igc_hw *hw);
s32 igc_check_for_copper_link(struct igc_hw *hw);
+s32 igc_config_fc_after_link_up(struct igc_hw *hw);
+s32 igc_force_mac_fc(struct igc_hw *hw);
void igc_init_rx_addrs(struct igc_hw *hw, u16 rar_count);
s32 igc_setup_link(struct igc_hw *hw);
void igc_clear_hw_cntrs_base(struct igc_hw *hw);
diff --git a/drivers/net/ethernet/intel/igc/igc_main.c b/drivers/net/ethernet/intel/igc/igc_main.c
index 14f324826604..e1a078e084f0 100644
--- a/drivers/net/ethernet/intel/igc/igc_main.c
+++ b/drivers/net/ethernet/intel/igc/igc_main.c
@@ -3403,6 +3403,25 @@ static int igc_probe(struct pci_dev *pdev,
netdev->min_mtu = ETH_MIN_MTU;
netdev->max_mtu = MAX_STD_JUMBO_FRAME_SIZE;
+ /* before reading the NVM, reset the controller to put the device in a
+ * known good starting state
+ */
+ hw->mac.ops.reset_hw(hw);
+
+ if (eth_platform_get_mac_address(&pdev->dev, hw->mac.addr)) {
+ /* copy the MAC address out of the NVM */
+ if (hw->mac.ops.read_mac_addr(hw))
+ dev_err(&pdev->dev, "NVM Read Error\n");
+ }
+
+ memcpy(netdev->dev_addr, hw->mac.addr, netdev->addr_len);
+
+ if (!is_valid_ether_addr(netdev->dev_addr)) {
+ dev_err(&pdev->dev, "Invalid MAC Address\n");
+ err = -EIO;
+ goto err_eeprom;
+ }
+
/* configure RXPBSIZE and TXPBSIZE */
wr32(IGC_RXPBS, I225_RXPBSIZE_DEFAULT);
wr32(IGC_TXPBS, I225_TXPBSIZE_DEFAULT);
@@ -3411,6 +3430,14 @@ static int igc_probe(struct pci_dev *pdev,
INIT_WORK(&adapter->reset_task, igc_reset_task);
+ /* Initialize link properties that are user-changeable */
+ adapter->fc_autoneg = true;
+ hw->mac.autoneg = true;
+ hw->phy.autoneg_advertised = 0xaf;
+
+ hw->fc.requested_mode = igc_fc_default;
+ hw->fc.current_mode = igc_fc_default;
+
/* reset the hardware with the new settings */
igc_reset(adapter);
@@ -3438,6 +3465,9 @@ static int igc_probe(struct pci_dev *pdev,
err_register:
igc_release_hw_control(adapter);
+err_eeprom:
+ if (!igc_check_reset_block(hw))
+ igc_reset_phy(hw);
err_sw_init:
igc_clear_interrupt_scheme(adapter);
iounmap(adapter->io_addr);
diff --git a/drivers/net/ethernet/intel/igc/igc_phy.c b/drivers/net/ethernet/intel/igc/igc_phy.c
index 88583c1d4970..38e43e6fc1c7 100644
--- a/drivers/net/ethernet/intel/igc/igc_phy.c
+++ b/drivers/net/ethernet/intel/igc/igc_phy.c
@@ -3,6 +3,10 @@
#include "igc_phy.h"
+/* forward declaration */
+static s32 igc_phy_setup_autoneg(struct igc_hw *hw);
+static s32 igc_wait_autoneg(struct igc_hw *hw);
+
/**
* igc_check_reset_block - Check if PHY reset is blocked
* @hw: pointer to the HW structure
@@ -211,6 +215,336 @@ s32 igc_phy_hw_reset(struct igc_hw *hw)
return ret_val;
}
+/**
+ * igc_copper_link_autoneg - Setup/Enable autoneg for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Performs initial bounds checking on autoneg advertisement parameter, then
+ * configure to advertise the full capability. Setup the PHY to autoneg
+ * and restart the negotiation process between the link partner. If
+ * autoneg_wait_to_complete, then wait for autoneg to complete before exiting.
+ */
+static s32 igc_copper_link_autoneg(struct igc_hw *hw)
+{
+ struct igc_phy_info *phy = &hw->phy;
+ u16 phy_ctrl;
+ s32 ret_val;
+
+ /* Perform some bounds checking on the autoneg advertisement
+ * parameter.
+ */
+ phy->autoneg_advertised &= phy->autoneg_mask;
+
+ /* If autoneg_advertised is zero, we assume it was not defaulted
+ * by the calling code so we set to advertise full capability.
+ */
+ if (phy->autoneg_advertised == 0)
+ phy->autoneg_advertised = phy->autoneg_mask;
+
+ hw_dbg("Reconfiguring auto-neg advertisement params\n");
+ ret_val = igc_phy_setup_autoneg(hw);
+ if (ret_val) {
+ hw_dbg("Error Setting up Auto-Negotiation\n");
+ goto out;
+ }
+ hw_dbg("Restarting Auto-Neg\n");
+
+ /* Restart auto-negotiation by setting the Auto Neg Enable bit and
+ * the Auto Neg Restart bit in the PHY control register.
+ */
+ ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl);
+ if (ret_val)
+ goto out;
+
+ phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+ ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl);
+ if (ret_val)
+ goto out;
+
+ /* Does the user want to wait for Auto-Neg to complete here, or
+ * check at a later time (for example, callback routine).
+ */
+ if (phy->autoneg_wait_to_complete) {
+ ret_val = igc_wait_autoneg(hw);
+ if (ret_val) {
+ hw_dbg("Error while waiting for autoneg to complete\n");
+ goto out;
+ }
+ }
+
+ hw->mac.get_link_status = true;
+
+out:
+ return ret_val;
+}
+
+/**
+ * igc_wait_autoneg - Wait for auto-neg completion
+ * @hw: pointer to the HW structure
+ *
+ * Waits for auto-negotiation to complete or for the auto-negotiation time
+ * limit to expire, which ever happens first.
+ */
+static s32 igc_wait_autoneg(struct igc_hw *hw)
+{
+ u16 i, phy_status;
+ s32 ret_val = 0;
+
+ /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
+ for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
+ ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
+ if (ret_val)
+ break;
+ if (phy_status & MII_SR_AUTONEG_COMPLETE)
+ break;
+ msleep(100);
+ }
+
+ /* PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
+ * has completed.
+ */
+ return ret_val;
+}
+
+/**
+ * igc_phy_setup_autoneg - Configure PHY for auto-negotiation
+ * @hw: pointer to the HW structure
+ *
+ * Reads the MII auto-neg advertisement register and/or the 1000T control
+ * register and if the PHY is already setup for auto-negotiation, then
+ * return successful. Otherwise, setup advertisement and flow control to
+ * the appropriate values for the wanted auto-negotiation.
+ */
+static s32 igc_phy_setup_autoneg(struct igc_hw *hw)
+{
+ struct igc_phy_info *phy = &hw->phy;
+ u16 aneg_multigbt_an_ctrl = 0;
+ u16 mii_1000t_ctrl_reg = 0;
+ u16 mii_autoneg_adv_reg;
+ s32 ret_val;
+
+ phy->autoneg_advertised &= phy->autoneg_mask;
+
+ /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+ ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL,
+ &mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+ }
+
+ if ((phy->autoneg_mask & ADVERTISE_2500_FULL) &&
+ hw->phy.id == I225_I_PHY_ID) {
+ /* Read the MULTI GBT AN Control Register - reg 7.32 */
+ ret_val = phy->ops.read_reg(hw, (STANDARD_AN_REG_MASK <<
+ MMD_DEVADDR_SHIFT) |
+ ANEG_MULTIGBT_AN_CTRL,
+ &aneg_multigbt_an_ctrl);
+
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Need to parse both autoneg_advertised and fc and set up
+ * the appropriate PHY registers. First we will parse for
+ * autoneg_advertised software override. Since we can advertise
+ * a plethora of combinations, we need to check each bit
+ * individually.
+ */
+
+ /* First we clear all the 10/100 mb speed bits in the Auto-Neg
+ * Advertisement Register (Address 4) and the 1000 mb speed bits in
+ * the 1000Base-T Control Register (Address 9).
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
+ NWAY_AR_100TX_HD_CAPS |
+ NWAY_AR_10T_FD_CAPS |
+ NWAY_AR_10T_HD_CAPS);
+ mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
+
+ hw_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
+
+ /* Do we want to advertise 10 Mb Half Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
+ hw_dbg("Advertise 10mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ }
+
+ /* Do we want to advertise 10 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
+ hw_dbg("Advertise 10mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Half Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
+ hw_dbg("Advertise 100mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+ }
+
+ /* Do we want to advertise 100 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
+ hw_dbg("Advertise 100mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+ }
+
+ /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+ if (phy->autoneg_advertised & ADVERTISE_1000_HALF)
+ hw_dbg("Advertise 1000mb Half duplex request denied!\n");
+
+ /* Do we want to advertise 1000 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
+ hw_dbg("Advertise 1000mb Full duplex\n");
+ mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ }
+
+ /* We do not allow the Phy to advertise 2500 Mb Half Duplex */
+ if (phy->autoneg_advertised & ADVERTISE_2500_HALF)
+ hw_dbg("Advertise 2500mb Half duplex request denied!\n");
+
+ /* Do we want to advertise 2500 Mb Full Duplex? */
+ if (phy->autoneg_advertised & ADVERTISE_2500_FULL) {
+ hw_dbg("Advertise 2500mb Full duplex\n");
+ aneg_multigbt_an_ctrl |= CR_2500T_FD_CAPS;
+ } else {
+ aneg_multigbt_an_ctrl &= ~CR_2500T_FD_CAPS;
+ }
+
+ /* Check for a software override of the flow control settings, and
+ * setup the PHY advertisement registers accordingly. If
+ * auto-negotiation is enabled, then software will have to set the
+ * "PAUSE" bits to the correct value in the Auto-Negotiation
+ * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
+ * negotiation.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * but we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: No software override. The flow control configuration
+ * in the EEPROM is used.
+ */
+ switch (hw->fc.current_mode) {
+ case igc_fc_none:
+ /* Flow control (Rx & Tx) is completely disabled by a
+ * software over-ride.
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case igc_fc_rx_pause:
+ /* Rx Flow control is enabled, and Tx Flow control is
+ * disabled, by a software over-ride.
+ *
+ * Since there really isn't a way to advertise that we are
+ * capable of Rx Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric Rx PAUSE. Later
+ * (in igc_config_fc_after_link_up) we will disable the
+ * hw's ability to send PAUSE frames.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case igc_fc_tx_pause:
+ /* Tx Flow control is enabled, and Rx Flow control is
+ * disabled, by a software over-ride.
+ */
+ mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+ mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+ break;
+ case igc_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by a software
+ * over-ride.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ default:
+ hw_dbg("Flow control param set incorrectly\n");
+ return -IGC_ERR_CONFIG;
+ }
+
+ ret_val = phy->ops.write_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+
+ hw_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+
+ if (phy->autoneg_mask & ADVERTISE_1000_FULL)
+ ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL,
+ mii_1000t_ctrl_reg);
+
+ if ((phy->autoneg_mask & ADVERTISE_2500_FULL) &&
+ hw->phy.id == I225_I_PHY_ID)
+ ret_val = phy->ops.write_reg(hw,
+ (STANDARD_AN_REG_MASK <<
+ MMD_DEVADDR_SHIFT) |
+ ANEG_MULTIGBT_AN_CTRL,
+ aneg_multigbt_an_ctrl);
+
+ return ret_val;
+}
+
+/**
+ * igc_setup_copper_link - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Calls the appropriate function to configure the link for auto-neg or forced
+ * speed and duplex. Then we check for link, once link is established calls
+ * to configure collision distance and flow control are called. If link is
+ * not established, we return -IGC_ERR_PHY (-2).
+ */
+s32 igc_setup_copper_link(struct igc_hw *hw)
+{
+ s32 ret_val = 0;
+ bool link;
+
+ if (hw->mac.autoneg) {
+ /* Setup autoneg and flow control advertisement and perform
+ * autonegotiation.
+ */
+ ret_val = igc_copper_link_autoneg(hw);
+ if (ret_val)
+ goto out;
+ } else {
+ /* PHY will be set to 10H, 10F, 100H or 100F
+ * depending on user settings.
+ */
+ hw_dbg("Forcing Speed and Duplex\n");
+ ret_val = hw->phy.ops.force_speed_duplex(hw);
+ if (ret_val) {
+ hw_dbg("Error Forcing Speed and Duplex\n");
+ goto out;
+ }
+ }
+
+ /* Check link status. Wait up to 100 microseconds for link to become
+ * valid.
+ */
+ ret_val = igc_phy_has_link(hw, COPPER_LINK_UP_LIMIT, 10, &link);
+ if (ret_val)
+ goto out;
+
+ if (link) {
+ hw_dbg("Valid link established!!!\n");
+ igc_config_collision_dist(hw);
+ ret_val = igc_config_fc_after_link_up(hw);
+ } else {
+ hw_dbg("Unable to establish link!!!\n");
+ }
+
+out:
+ return ret_val;
+}
+
/**
* igc_read_phy_reg_mdic - Read MDI control register
* @hw: pointer to the HW structure
diff --git a/drivers/net/ethernet/intel/igc/igc_phy.h b/drivers/net/ethernet/intel/igc/igc_phy.h
index 6a62f381559d..25cba33de7e2 100644
--- a/drivers/net/ethernet/intel/igc/igc_phy.h
+++ b/drivers/net/ethernet/intel/igc/igc_phy.h
@@ -12,6 +12,7 @@ s32 igc_get_phy_id(struct igc_hw *hw);
s32 igc_phy_has_link(struct igc_hw *hw, u32 iterations,
u32 usec_interval, bool *success);
s32 igc_check_downshift(struct igc_hw *hw);
+s32 igc_setup_copper_link(struct igc_hw *hw);
void igc_power_up_phy_copper(struct igc_hw *hw);
void igc_power_down_phy_copper(struct igc_hw *hw);
s32 igc_write_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 data);
--
2.17.2
Powered by blists - more mailing lists