| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Fri, 9 Nov 2018 00:06:01 +0530
From: sunil.kovvuri@...il.com
To: netdev@...r.kernel.org, davem@...emloft.net
Cc: arnd@...db.de, linux-soc@...r.kernel.org,
Sunil Goutham <sgoutham@...vell.com>,
Jerin Jacob <jerinj@...vell.com>
Subject: [PATCH 20/20] octeontx2-af: Workarounds for HW errata
From: Sunil Goutham <sgoutham@...vell.com>
Errata 35038
Software sets NIX_AF_RX_SW_SYNC[ENA] to sync (flush) in-flight packets
the RX data path before configuration changes (e.g. disabling one or
more RQs). Hardware clears [ENA] to indicate sync is done
An issue exists whereby NIX may clear NIX_AF_RX_SW_SYNC [ENA] too
early.
Errata 35057
NIX may corrupt internal state when conditional clocks turn off.
So turnon all clocks by default.
Errata 35786
Parse nibble enable NPC configuration for KEY generation has to be
identical for both Rx and Tx interfaces.
Also corrected endianness configuration for NIX i.e NIX_AF_CFG[AF_BE]
is bit8 and not bit1.
Signed-off-by: Sunil Goutham <sgoutham@...vell.com>
Signed-off-by: Jerin Jacob <jerinj@...vell.com>
---
drivers/net/ethernet/marvell/octeontx2/af/rvu.h | 12 ++++++++++++
drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c | 18 ++++++++++++++++--
drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c | 12 +++++++++---
3 files changed, 37 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ethernet/marvell/octeontx2/af/rvu.h b/drivers/net/ethernet/marvell/octeontx2/af/rvu.h
index cf9139e..aa9f8c2 100644
--- a/drivers/net/ethernet/marvell/octeontx2/af/rvu.h
+++ b/drivers/net/ethernet/marvell/octeontx2/af/rvu.h
@@ -11,6 +11,7 @@
#ifndef RVU_H
#define RVU_H
+#include <linux/pci.h>
#include "rvu_struct.h"
#include "common.h"
#include "mbox.h"
@@ -18,6 +19,9 @@
/* PCI device IDs */
#define PCI_DEVID_OCTEONTX2_RVU_AF 0xA065
+/* Subsystem Device ID */
+#define PCI_SUBSYS_DEVID_96XX 0xB200
+
/* PCI BAR nos */
#define PCI_AF_REG_BAR_NUM 0
#define PCI_PF_REG_BAR_NUM 2
@@ -255,6 +259,14 @@ static inline u64 rvupf_read64(struct rvu *rvu, u64 offset)
return readq(rvu->pfreg_base + offset);
}
+static inline bool is_rvu_9xxx_A0(struct rvu *rvu)
+{
+ struct pci_dev *pdev = rvu->pdev;
+
+ return (pdev->revision == 0x00) &&
+ (pdev->subsystem_device == PCI_SUBSYS_DEVID_96XX);
+}
+
/* Function Prototypes
* RVU
*/
diff --git a/drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c b/drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c
index 1f73c05..63df40d 100644
--- a/drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c
+++ b/drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c
@@ -114,6 +114,12 @@ static void nix_rx_sync(struct rvu *rvu, int blkaddr)
err = rvu_poll_reg(rvu, blkaddr, NIX_AF_RX_SW_SYNC, BIT_ULL(0), true);
if (err)
dev_err(rvu->dev, "NIX RX software sync failed\n");
+
+ /* As per a HW errata in 9xxx A0 silicon, HW may clear SW_SYNC[ENA]
+ * bit too early. Hence wait for 50us more.
+ */
+ if (is_rvu_9xxx_A0(rvu))
+ usleep_range(50, 60);
}
static bool is_valid_txschq(struct rvu *rvu, int blkaddr,
@@ -2135,10 +2141,10 @@ static int nix_aq_init(struct rvu *rvu, struct rvu_block *block)
/* Set admin queue endianness */
cfg = rvu_read64(rvu, block->addr, NIX_AF_CFG);
#ifdef __BIG_ENDIAN
- cfg |= BIT_ULL(1);
+ cfg |= BIT_ULL(8);
rvu_write64(rvu, block->addr, NIX_AF_CFG, cfg);
#else
- cfg &= ~BIT_ULL(1);
+ cfg &= ~BIT_ULL(8);
rvu_write64(rvu, block->addr, NIX_AF_CFG, cfg);
#endif
@@ -2175,6 +2181,14 @@ int rvu_nix_init(struct rvu *rvu)
return 0;
block = &hw->block[blkaddr];
+ /* As per a HW errata in 9xxx A0 silicon, NIX may corrupt
+ * internal state when conditional clocks are turned off.
+ * Hence enable them.
+ */
+ if (is_rvu_9xxx_A0(rvu))
+ rvu_write64(rvu, blkaddr, NIX_AF_CFG,
+ rvu_read64(rvu, blkaddr, NIX_AF_CFG) | 0x5EULL);
+
/* Calibrate X2P bus to check if CGX/LBK links are fine */
err = nix_calibrate_x2p(rvu, blkaddr);
if (err)
diff --git a/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c b/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c
index e61f5b3..bff253c 100644
--- a/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c
+++ b/drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c
@@ -973,7 +973,7 @@ int rvu_npc_init(struct rvu *rvu)
struct npc_pkind *pkind = &rvu->hw->pkind;
u64 keyz = NPC_MCAM_KEY_X2;
int blkaddr, entry, bank, err;
- u64 cfg;
+ u64 cfg, nibble_ena;
blkaddr = rvu_get_blkaddr(rvu, BLKTYPE_NPC, 0);
if (blkaddr < 0) {
@@ -1022,10 +1022,16 @@ int rvu_npc_init(struct rvu *rvu)
/* Set RX and TX side MCAM search key size.
* LA..LD (ltype only) + Channel
*/
+ nibble_ena = 0x49247;
rvu_write64(rvu, blkaddr, NPC_AF_INTFX_KEX_CFG(NIX_INTF_RX),
- ((keyz & 0x3) << 32) | 0x49247);
+ ((keyz & 0x3) << 32) | nibble_ena);
+ /* Due to an errata (35786) in A0 pass silicon, parse nibble enable
+ * configuration has to be identical for both Rx and Tx interfaces.
+ */
+ if (!is_rvu_9xxx_A0(rvu))
+ nibble_ena = (1ULL << 19) - 1;
rvu_write64(rvu, blkaddr, NPC_AF_INTFX_KEX_CFG(NIX_INTF_TX),
- ((keyz & 0x3) << 32) | ((1ULL << 19) - 1));
+ ((keyz & 0x3) << 32) | nibble_ena);
err = npc_mcam_rsrcs_init(rvu, blkaddr);
if (err)
--
2.7.4
Powered by blists - more mailing lists