| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Fri, 16 Nov 2018 17:03:25 -0800
From: Sean Wang <sean.wang@...nel.org>
To: biao.huang@...iatek.com
Cc: davem@...emloft.net, robh+dt@...nel.org, mark.rutland@....com,
devicetree@...r.kernel.org, nelson.chang@...iatek.com,
andrew@...n.ch, netdev@...r.kernel.org, liguo.zhang@...iatek.com,
linux-kernel@...r.kernel.org,
Matthias Brugger <matthias.bgg@...il.com>,
joabreu@...opsys.com, linux-mediatek@...ts.infradead.org,
honghui.zhang@...iatek.com, linux-arm-kernel@...ts.infradead.org
Subject: Re: [v3, PATCH 1/2] net:stmmac: dwmac-mediatek: add support for mt2712
wi
On Fri, Nov 16, 2018 at 1:19 AM Biao Huang <biao.huang@...iatek.com> wrote:
>
> Add Ethernet support for MediaTek SoCs from the mt2712 family
>
> Change-Id: Id3c535627088227793bd36405994edf2dc765e6a
Drop change-Id
> Signed-off-by: Biao Huang <biao.huang@...iatek.com>
> ---
> drivers/net/ethernet/stmicro/stmmac/Kconfig | 8 +
> drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
> .../net/ethernet/stmicro/stmmac/dwmac-mediatek.c | 383 ++++++++++++++++++++
> 3 files changed, 392 insertions(+)
> create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
>
> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> index edf2036..28a7a28 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> @@ -75,6 +75,14 @@ config DWMAC_LPC18XX
> ---help---
> Support for NXP LPC18xx/43xx DWMAC Ethernet.
>
> +config DWMAC_MEDIATEK
> + tristate "MediaTek MT27xx GMAC support"
> + depends on OF && (ARCH_MEDIATEK || COMPILE_TEST)
> + help
> + Support for MediaTek GMAC Ethernet controller.
> +
> + This selects the MT2712 SoC support for the stmmac driver.
> +
> config DWMAC_MESON
> tristate "Amlogic Meson dwmac support"
> default ARCH_MESON
> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
> index 99967a8..bf09701 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
> @@ -13,6 +13,7 @@ obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o
> obj-$(CONFIG_DWMAC_ANARION) += dwmac-anarion.o
> obj-$(CONFIG_DWMAC_IPQ806X) += dwmac-ipq806x.o
> obj-$(CONFIG_DWMAC_LPC18XX) += dwmac-lpc18xx.o
> +obj-$(CONFIG_DWMAC_MEDIATEK) += dwmac-mediatek.o
> obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o dwmac-meson8b.o
> obj-$(CONFIG_DWMAC_OXNAS) += dwmac-oxnas.o
> obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o
> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> new file mode 100644
> index 0000000..a80b3e0
> --- /dev/null
> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> @@ -0,0 +1,383 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2018 MediaTek Inc.
> + */
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_net.h>
> +#include <linux/regmap.h>
> +#include <linux/stmmac.h>
> +
> +#include "stmmac.h"
> +#include "stmmac_platform.h"
> +
> +/* Peri Configuration register */
> +#define PERI_ETH_PHY_INTF_SEL 0x418
> +#define PHY_INTF_MII_GMII 0
> +#define PHY_INTF_RGMII 1
> +#define PHY_INTF_RMII 4
> +#define RMII_CLK_SRC_RXC BIT(4)
> +#define RMII_CLK_SRC_INTERNAL BIT(5)
> +
> +#define PERI_ETH_PHY_DLY 0x428
> +#define PHY_DLY_GTXC_INV BIT(6)
> +#define PHY_DLY_GTXC_ENABLE BIT(5)
> +#define PHY_DLY_GTXC_STAGES GENMASK(4, 0)
> +#define PHY_DLY_TXC_INV BIT(20)
> +#define PHY_DLY_TXC_ENABLE BIT(19)
> +#define PHY_DLY_TXC_STAGES GENMASK(18, 14)
> +#define PHY_DLY_TXC_SHIFT 14
> +#define PHY_DLY_RXC_INV BIT(13)
> +#define PHY_DLY_RXC_ENABLE BIT(12)
> +#define PHY_DLY_RXC_STAGES GENMASK(11, 7)
> +#define PHY_DLY_RXC_SHIFT 7
> +
> +#define PERI_ETH_DLY_FINE 0x800
> +#define ETH_RMII_DLY_TX_INV BIT(2)
> +#define ETH_FINE_DLY_GTXC BIT(1)
> +#define ETH_FINE_DLY_RXC BIT(0)
> +
> +enum dwmac_clks_map {
> + DWMAC_CLK_AXI_DRAM,
> + DWMAC_CLK_APB_REG,
> + DWMAC_CLK_MAC_EXT,
> + DWMAC_CLK_MAC_PARENT,
> + DWMAC_CLK_PTP_REF,
> + DWMAC_CLK_PTP_PARENT,
> + DWMAC_CLK_PTP_TOP,
> + DWMAC_CLK_MAX
> +};
> +
> +struct mac_delay_struct {
> + u32 tx_delay;
> + u32 rx_delay;
> + u32 tx_inv;
> + u32 rx_inv;
> +};
> +
> +struct mediatek_dwmac_plat_data {
> + struct device *dev;
> + struct regmap *peri_regmap;
> + struct clk *clks[DWMAC_CLK_MAX];
> + struct device_node *np;
> + int phy_mode;
> + struct mac_delay_struct mac_delay;
> + const struct mediatek_dwmac_variant *variant;
> + int fine_tune;
> + int rmii_rxc;
> +};
> +
> +struct mediatek_dwmac_variant {
> + int (*dwmac_config_dt)(struct mediatek_dwmac_plat_data *plat);
> + int (*dwmac_enable_clks)(struct mediatek_dwmac_plat_data *plat);
> + void (*dwmac_disable_clks)(struct mediatek_dwmac_plat_data *plat);
Each variant usually can reuse the same config_dt, enable/disable_clks function.
> + u32 rx_delay_max;
> + u32 tx_delay_max;
> +};
> +
> +static const char * const mediatek_dwmac_clks_name[] = {
> + "axi", "apb", "mac_ext", "mac_parent", "ptp_ref", "ptp_parent", "ptp_top"
> +};
> +
> +static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
Kconfig indicates it's a mt27xx driver. so it's good if there is a
more generic prefix.
> +{
> + int rmii_rxc = plat->rmii_rxc ? RMII_CLK_SRC_RXC : 0;
> + u32 intf_val = 0;
> +
> + /* select phy interface in top control domain */
> + switch (plat->phy_mode) {
> + case PHY_INTERFACE_MODE_MII:
> + intf_val |= PHY_INTF_MII_GMII;
> + break;
> + case PHY_INTERFACE_MODE_RMII:
> + intf_val |= PHY_INTF_RMII;
> + intf_val |= rmii_rxc;
> + break;
> + case PHY_INTERFACE_MODE_RGMII:
> + case PHY_INTERFACE_MODE_RGMII_TXID:
> + case PHY_INTERFACE_MODE_RGMII_RXID:
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + intf_val |= PHY_INTF_RGMII;
> + break;
> + default:
> + dev_err(plat->dev, "phy interface not supported\n");
> + return -EINVAL;
> + }
> +
> + regmap_write(plat->peri_regmap, PERI_ETH_PHY_INTF_SEL, intf_val);
> +
> + return 0;
> +}
> +
> +static int mt2712_set_delay(struct mediatek_dwmac_plat_data *plat)
> +{
> + struct mac_delay_struct *mac_delay = &plat->mac_delay;
> + u32 delay_val = 0;
> + u32 fine_val = 0;
> +
> + switch (plat->phy_mode) {
> + case PHY_INTERFACE_MODE_MII:
> + delay_val |= mac_delay->tx_delay ? PHY_DLY_TXC_ENABLE : 0;
> + delay_val |= (mac_delay->tx_delay << PHY_DLY_TXC_SHIFT) &
> + PHY_DLY_TXC_STAGES;
> + delay_val |= mac_delay->tx_inv ? PHY_DLY_TXC_INV : 0;
> + delay_val |= mac_delay->rx_delay ? PHY_DLY_RXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay << PHY_DLY_RXC_SHIFT) &
> + PHY_DLY_RXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_RXC_INV : 0;
> + break;
> + case PHY_INTERFACE_MODE_RMII:
> + if (plat->rmii_rxc) {
> + delay_val |= mac_delay->rx_delay ?
> + PHY_DLY_RXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay <<
> + PHY_DLY_RXC_SHIFT) & PHY_DLY_RXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_RXC_INV : 0;
> + fine_val |= mac_delay->tx_inv ?
> + ETH_RMII_DLY_TX_INV : 0;
> + } else {
> + delay_val |= mac_delay->rx_delay ?
> + PHY_DLY_TXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay <<
> + PHY_DLY_TXC_SHIFT) & PHY_DLY_TXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_TXC_INV : 0;
> + fine_val |= mac_delay->tx_inv ?
> + ETH_RMII_DLY_TX_INV : 0;
> + }
> + break;
> + case PHY_INTERFACE_MODE_RGMII:
> + fine_val = plat->fine_tune ?
> + (ETH_FINE_DLY_GTXC | ETH_FINE_DLY_RXC) : 0;
> + delay_val |= mac_delay->tx_delay ? PHY_DLY_GTXC_ENABLE : 0;
> + delay_val |= mac_delay->tx_delay & PHY_DLY_GTXC_STAGES;
> + delay_val |= mac_delay->tx_inv ? PHY_DLY_GTXC_INV : 0;
> + delay_val |= mac_delay->rx_delay ? PHY_DLY_RXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay << PHY_DLY_RXC_SHIFT) &
> + PHY_DLY_RXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_RXC_INV : 0;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_TXID:
> + fine_val = plat->fine_tune ? ETH_FINE_DLY_RXC : 0;
> + delay_val |= mac_delay->rx_delay ? PHY_DLY_RXC_ENABLE : 0;
> + delay_val |= (mac_delay->rx_delay << PHY_DLY_RXC_SHIFT) &
> + PHY_DLY_RXC_STAGES;
> + delay_val |= mac_delay->rx_inv ? PHY_DLY_RXC_INV : 0;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_RXID:
> + fine_val = plat->fine_tune ? ETH_FINE_DLY_GTXC : 0;
> + delay_val |= mac_delay->tx_delay ? PHY_DLY_GTXC_ENABLE : 0;
> + delay_val |= mac_delay->tx_delay & PHY_DLY_GTXC_STAGES;
> + delay_val |= mac_delay->tx_inv ? PHY_DLY_GTXC_INV : 0;
> + break;
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + break;
> + default:
> + dev_err(plat->dev, "phy interface not supported\n");
> + return -EINVAL;
> + }
> + regmap_write(plat->peri_regmap, PERI_ETH_PHY_DLY, delay_val);
> + regmap_write(plat->peri_regmap, PERI_ETH_DLY_FINE, fine_val);
> +
> + return 0;
> +}
> +
> +static int mt2712_get_clks(struct mediatek_dwmac_plat_data *plat)
> +{
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(plat->clks); i++) {
> + plat->clks[i] = devm_clk_get(plat->dev,
> + mediatek_dwmac_clks_name[i]);
> + if (IS_ERR(plat->clks[i]))
> + return PTR_ERR(plat->clks[i]);
> + }
can we use devm_clk_bulk_get?
> +
> + return 0;
> +}
> +
> +static int mt2712_enable_clks(struct mediatek_dwmac_plat_data *plat)
> +{
> + int clk, ret;
> +
> + for (clk = 0; clk < DWMAC_CLK_MAX ; clk++) {
> + ret = clk_prepare_enable(plat->clks[clk]);
> + if (ret)
> + goto err_disable_clks;
> + }
can we use clk_bulk_enable?
> +
> + ret = clk_set_parent(plat->clks[DWMAC_CLK_MAC_EXT], plat->clks[DWMAC_CLK_MAC_PARENT]);
> + if (ret)
> + goto err_disable_clks;
> +
> + ret = clk_set_parent(plat->clks[DWMAC_CLK_PTP_REF], plat->clks[DWMAC_CLK_PTP_PARENT]);
> + if (ret)
> + goto err_disable_clks;
> +
I guess clk_set_parent can be trimmed if we involve assigned-clocks,
assigned-clock-parents, assigned-clock-rates in the dts
> + return 0;
> +
> +err_disable_clks:
> + while (--clk >= 0)
> + clk_disable_unprepare(plat->clks[clk]);
> +
clk_bulk_enable would take care about the failed case
> + return ret;
> +}
> +
> +static void mt2712_disable_clks(struct mediatek_dwmac_plat_data *plat)
> +{
> + int clk;
> +
> + for (clk = DWMAC_CLK_MAX - 1; clk >= 0; clk--)
> + clk_disable_unprepare(plat->clks[clk]);
> +}
can we use clk_bulk_disable ?
> +
> +static int mt2712_config_dt(struct mediatek_dwmac_plat_data *plat)
> +{
> + u32 tx_delay, rx_delay;
> +
> + plat->peri_regmap = syscon_regmap_lookup_by_compatible("mediatek,mt2712-pericfg");
the driver would be not generic enough if we assigned a specific
string into here.
how about apply syscon_regmap_lookup_by_phandle in here?
> + if (IS_ERR(plat->peri_regmap)) {
> + dev_err(plat->dev, "Failed to get pericfg syscon\n");
> + return PTR_ERR(plat->peri_regmap);
> + }
> +
> + if (!of_property_read_u32(plat->np, "tx-delay", &tx_delay)) {
> + if (tx_delay < plat->variant->tx_delay_max) {
> + plat->mac_delay.tx_delay = tx_delay;
> + } else {
> + dev_err(plat->dev, "Invalid TX clock delay: %d\n", tx_delay);
> + return -EINVAL;
> + }
> + }
> +
> + if (!of_property_read_u32(plat->np, "rx-delay", &rx_delay)) {
> + if (rx_delay < plat->variant->rx_delay_max) {
> + plat->mac_delay.rx_delay = rx_delay;
> + } else {
> + dev_err(plat->dev, "Invalid RX clock delay: %d\n", rx_delay);
> + return -EINVAL;
> + }
> + }
> +
> + plat->mac_delay.tx_inv = of_property_read_bool(plat->np, "txc-inverse");
> +
can we drop the empty line?
> + plat->mac_delay.rx_inv = of_property_read_bool(plat->np, "rxc-inverse");
> +
can we drop the empty line?
> + plat->fine_tune = of_property_read_bool(plat->np, "fine-tune");
> +
can we drop the empty line?
> + plat->rmii_rxc = of_property_read_bool(plat->np, "rmii-rxc");
> +
> + mt2712_set_interface(plat);
> +
> + mt2712_set_delay(plat);
> +
> + return mt2712_get_clks(plat);
> +}
> +
> +static const struct mediatek_dwmac_variant mt2712_gmac_variant = {
> + .dwmac_config_dt = mt2712_config_dt,
> + .dwmac_enable_clks = mt2712_enable_clks,
> + .dwmac_disable_clks = mt2712_disable_clks,
> + .rx_delay_max = 32,
> + .tx_delay_max = 32,
> +};
I thought we add the variant structure when the SoC variant is really in.
> +
> +static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
> +{
> + const struct mediatek_dwmac_variant *variant = plat->variant;
> +
> + /* Set the DMA mask, 4GB mode enabled */
> + dma_set_mask_and_coherent(plat->dev, DMA_BIT_MASK(33));
> +
> + return variant->dwmac_config_dt(plat);
> +}
> +
> +static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
> +{
> + struct mediatek_dwmac_plat_data *plat = priv;
> + const struct mediatek_dwmac_variant *variant = plat->variant;
> +
> + return variant->dwmac_enable_clks(plat);
> +}
> +
> +static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv)
> +{
> + struct mediatek_dwmac_plat_data *plat = priv;
> + const struct mediatek_dwmac_variant *variant = plat->variant;
> +
> + variant->dwmac_disable_clks(plat);
> +}
> +
> +static int mediatek_dwmac_probe(struct platform_device *pdev)
> +{
> + int ret = 0;
> + struct plat_stmmacenet_data *plat_dat;
> + struct stmmac_resources stmmac_res;
> + struct mediatek_dwmac_plat_data *priv_plat;
sorting these declarations into reverse Xmas tree seems to be good
> +
> + priv_plat = devm_kzalloc(&pdev->dev, sizeof(*priv_plat), GFP_KERNEL);
> + if (!priv_plat)
> + return -ENOMEM;
> +
> + priv_plat->variant = of_device_get_match_data(&pdev->dev);
> + if (!priv_plat->variant) {
> + dev_err(&pdev->dev, "Missing dwmac-mediatek variant\n");
> + return -EINVAL;
> + }
> +
> + priv_plat->dev = &pdev->dev;
> + priv_plat->np = pdev->dev.of_node;
> + priv_plat->phy_mode = of_get_phy_mode(priv_plat->np);
> +
> + ret = mediatek_dwmac_config_dt(priv_plat);
> + if (ret)
> + return ret;
> +
> + ret = stmmac_get_platform_resources(pdev, &stmmac_res);
> + if (ret)
> + return ret;
> +
> + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac);
> + if (IS_ERR(plat_dat))
> + return PTR_ERR(plat_dat);
> +
> + plat_dat->interface = priv_plat->phy_mode;
> + /* clk_csr_i = 250-300MHz & MDC = clk_csr_i/124 */
> + plat_dat->clk_csr = 5;
> + plat_dat->has_gmac4 = 1;
> + plat_dat->has_gmac = 0;
> + plat_dat->pmt = 0;
> + plat_dat->maxmtu = ETH_DATA_LEN;
> + plat_dat->bsp_priv = priv_plat;
> + plat_dat->init = mediatek_dwmac_init;
> + plat_dat->exit = mediatek_dwmac_exit;
> + mediatek_dwmac_init(pdev, priv_plat);
> +
> + ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
> + if (ret) {
> + stmmac_remove_config_dt(pdev, plat_dat);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id mediatek_dwmac_match[] = {
> + { .compatible = "mediatek,mt2712-gmac",
> + .data = &mt2712_gmac_variant },
> + { }
> +};
> +
> +MODULE_DEVICE_TABLE(of, mediatek_dwmac_match);
> +
> +static struct platform_driver mediatek_dwmac_driver = {
> + .probe = mediatek_dwmac_probe,
> + .remove = stmmac_pltfr_remove,
> + .driver = {
> + .name = "dwmac-mediatek",
> + .pm = &stmmac_pltfr_pm_ops,
> + .of_match_table = mediatek_dwmac_match,
> + },
> +};
> +module_platform_driver(mediatek_dwmac_driver);
> --
> 1.7.9.5
>
>
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek@...ts.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
Powered by blists - more mailing lists