netdev - Re: [v3,4/5] net: phy: at803x: Disable phy delay for RGMII mode

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <147151c4-d162-4ebe-189a-564492d84d18@ti.com>
Date:   Tue, 12 Feb 2019 12:55:33 +0200
From:   Peter Ujfalusi <peter.ujfalusi@...com>
To:     Vinod Koul <vkoul@...nel.org>,
        David S Miller <davem@...emloft.net>,
        Roger Quadros <rogerq@...com>
CC:     <netdev@...r.kernel.org>, <linux-arm-msm@...r.kernel.org>,
        Niklas Cassel <niklas.cassel@...aro.org>,
        Bjorn Andersson <bjorn.andersson@...aro.org>,
        Andrew Lunn <andrew@...n.ch>,
        Florian Fainelli <f.fainelli@...il.com>,
        "Nori, Sekhar" <nsekhar@...com>
Subject: Re: [v3,4/5] net: phy: at803x: Disable phy delay for RGMII mode

Vinod,

On 21/01/2019 11.13, Vinod Koul wrote:
> For RGMII mode, phy delay should be disabled. Add this case along
> with disable delay routines.

In next-20190211 I need to revert this patch to get cpsw networking to work on am335x-evmsk. The board uses AR8031_AL1A PHY, which is handled by the phy/at803x.c

On next-20190211:
[    3.374601] net eth0: initializing cpsw version 1.12 (0)
[    3.384484] Atheros 8031 ethernet 4a101000.mdio:00: attached PHY driver [Atheros 8031 ethernet] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL)
[    3.400041] cpsw 4a100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    3.410813] mmc1: new SDIO card at address 0001
[    3.439362] IP-Config: Complete:
[    3.442649]      device=eth0, hwaddr=bc:6a:29:7d:2c:a9, ipaddr=10.0.0.90, mask=255.255.255.0, gw=10.0.0.1
[    3.452840]      host=10.0.0.90, domain=, nis-domain=(none)
[    3.458462]      bootserver=10.0.0.30, rootserver=10.0.0.30, rootpath=
[    3.466296] vwl1271: disabling
[    3.470195] ALSA device list:
[    3.473189]   #0: AM335x-EVMSK

After reverting this patch:
[    3.374636] net eth0: initializing cpsw version 1.12 (0)
[    3.384534] Atheros 8031 ethernet 4a101000.mdio:00: attached PHY driver [Atheros 8031 ethernet] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL)
[    3.400125] cpsw 4a100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    3.410866] mmc1: new SDIO card at address 0001
[    3.439379] IP-Config: Complete:
[    3.442666]      device=eth0, hwaddr=bc:6a:29:7d:2c:a9, ipaddr=10.0.0.90, mask=255.255.255.0, gw=10.0.0.1
[    3.452865]      host=10.0.0.90, domain=, nis-domain=(none)
[    3.458482]      bootserver=10.0.0.30, rootserver=10.0.0.30, rootpath=
[    3.466334] vwl1271: disabling
[    3.470245] ALSA device list:
[    3.473241]   #0: AM335x-EVMSK
[    3.501052] VFS: Mounted root (nfs filesystem) readonly on device 0:15.
[    3.508694] devtmpfs: mounted
[    3.514546] Freeing unused kernel memory: 1024K
[    3.520567] Run /sbin/init as init process

and the board boots to nfsroot fine.

 
> Signed-off-by: Vinod Koul <vkoul@...nel.org>
> ---
>  drivers/net/phy/at803x.c | 22 ++++++++++++----------
>  1 file changed, 12 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
> index f9432d053a22..8ff12938ab47 100644
> --- a/drivers/net/phy/at803x.c
> +++ b/drivers/net/phy/at803x.c
> @@ -110,16 +110,16 @@ static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
>  	return phy_write(phydev, AT803X_DEBUG_DATA, val);
>  }
>  
> -static inline int at803x_enable_rx_delay(struct phy_device *phydev)
> +static inline int at803x_disable_rx_delay(struct phy_device *phydev)
>  {
> -	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
> -					AT803X_DEBUG_RX_CLK_DLY_EN);
> +	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
> +				     AT803X_DEBUG_RX_CLK_DLY_EN, 0);
>  }
>  
> -static inline int at803x_enable_tx_delay(struct phy_device *phydev)
> +static inline int at803x_disable_tx_delay(struct phy_device *phydev)
>  {
> -	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5, 0,
> -					AT803X_DEBUG_TX_CLK_DLY_EN);
> +	return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_5,
> +				     AT803X_DEBUG_TX_CLK_DLY_EN, 0);
>  }
>  
>  /* save relevant PHY registers to private copy */
> @@ -256,15 +256,17 @@ static int at803x_config_init(struct phy_device *phydev)
>  		return ret;
>  
>  	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
> -			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
> -		ret = at803x_enable_rx_delay(phydev);
> +			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
> +			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
> +		ret = at803x_disable_rx_delay(phydev);
>  		if (ret < 0)
>  			return ret;
>  	}
>  
>  	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
> -			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
> -		ret = at803x_enable_tx_delay(phydev);
> +			phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
> +			phydev->interface == PHY_INTERFACE_MODE_RGMII) {
> +		ret = at803x_disable_tx_delay(phydev);
>  		if (ret < 0)
>  			return ret;
>  	}
> 

- Péter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki