[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20190408074042.74s5qckukcpore3e@flea>
Date: Mon, 8 Apr 2019 09:40:42 +0200
From: Maxime Ripard <maxime.ripard@...tlin.com>
To: megous@...ous.com
Cc: linux-sunxi@...glegroups.com, Chen-Yu Tsai <wens@...e.org>,
Rob Herring <robh+dt@...nel.org>,
Linus Walleij <linus.walleij@...aro.org>,
David Airlie <airlied@...ux.ie>,
Daniel Vetter <daniel@...ll.ch>,
Mark Rutland <mark.rutland@....com>,
Giuseppe Cavallaro <peppe.cavallaro@...com>,
Alexandre Torgue <alexandre.torgue@...com>,
Jose Abreu <joabreu@...opsys.com>,
"David S. Miller" <davem@...emloft.net>,
Maxime Coquelin <mcoquelin.stm32@...il.com>,
Arend van Spriel <arend.vanspriel@...adcom.com>,
Franky Lin <franky.lin@...adcom.com>,
Hante Meuleman <hante.meuleman@...adcom.com>,
Chi-Hsien Lin <chi-hsien.lin@...ress.com>,
Wright Feng <wright.feng@...ress.com>,
Kalle Valo <kvalo@...eaurora.org>,
Naveen Gupta <naveen.gupta@...ress.com>,
dri-devel@...ts.freedesktop.org, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
netdev@...r.kernel.org, linux-stm32@...md-mailman.stormreply.com,
linux-wireless@...r.kernel.org,
brcm80211-dev-list.pdl@...adcom.com,
brcm80211-dev-list@...ress.com, linux-gpio@...r.kernel.org
Subject: Re: [PATCH 07/12] arm64: dts: allwinner: orange-pi-3: Enable ethernet
On Sat, Apr 06, 2019 at 01:45:09AM +0200, megous@...ous.com wrote:
> From: Ondrej Jirman <megous@...ous.com>
>
> Orange Pi 3 has two regulators that power the Realtek RTL8211E.
> According to the phy datasheet, both regulators need to be enabled
> at the same time, but we can only specify a single phy-supply in
> the DT.
>
> This can be achieved by making one regulator depedning on the
> other via vin-supply. While it's not a technically correct
> description of the hardware, it achieves the purpose.
>
> All values of RX/TX delay were tested exhaustively and a middle
> one of the working values was chosen.
>
> Signed-off-by: Ondrej Jirman <megous@...ous.com>
> ---
> .../dts/allwinner/sun50i-h6-orangepi-3.dts | 44 +++++++++++++++++++
> 1 file changed, 44 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> index 644946749088..5270142527f5 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> @@ -15,6 +15,7 @@
>
> aliases {
> serial0 = &uart0;
> + ethernet0 = &emac;
> };
>
> chosen {
> @@ -64,6 +65,27 @@
> regulator-max-microvolt = <5000000>;
> regulator-always-on;
> };
> +
> + /*
> + * The board uses 2.5V RGMII signalling. Power sequence
> + * to enable the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2)
> + * power rails at the same time and to wait 100ms.
> + */
> + reg_gmac_2v5: gmac-2v5 {
> + compatible = "regulator-fixed";
> + regulator-name = "gmac-2v5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + startup-delay-us = <100000>;
> + enable-active-high;
> + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
Is enable-active-high still needed? It's redundant with the
GPIO_ACTIVE_HIGH flag.
The indentation is wrong here as well.
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
Download attachment "signature.asc" of type "application/pgp-signature" (229 bytes)
Powered by blists - more mailing lists