Date:   Sat,  4 May 2019 04:18:26 +0300
From:   Vladimir Oltean <olteanv@...il.com>
To:     f.fainelli@...il.com, vivien.didelot@...il.com, andrew@...n.ch,
        davem@...emloft.net
Cc:     netdev@...r.kernel.org, linux-kernel@...r.kernel.org,
        Vladimir Oltean <olteanv@...il.com>
Subject: [PATCH net-next 9/9] Documentation: net: dsa: sja1105: Add info about supported traffic modes

Signed-off-by: Vladimir Oltean <olteanv@...il.com>
---
 Documentation/networking/dsa/sja1105.rst | 49 ++++++++++++++++++++++++
 1 file changed, 49 insertions(+)

diff --git a/Documentation/networking/dsa/sja1105.rst b/Documentation/networking/dsa/sja1105.rst
index 7c13b40915c0..a70a04164d07 100644
--- a/Documentation/networking/dsa/sja1105.rst
+++ b/Documentation/networking/dsa/sja1105.rst
@@ -63,6 +63,38 @@ If that changed setting can be transmitted to the switch through the dynamic
 reconfiguration interface, it is; otherwise the switch is reset and
 reprogrammed with the updated static configuration.
 
+Traffic support
+===============
+
+The switches do not support switch tagging in hardware. But they do support
+customizing the TPID by which VLAN traffic is identified as such. The switch
+driver is leveraging ``CONFIG_NET_DSA_TAG_8021Q`` by requesting that special
+VLANs (with a custom TPID of ``ETH_P_EDSA`` instead of ``ETH_P_8021Q``) are
+installed on its ports when not in ``vlan_filtering`` mode. This does not
+interfere with the reception and transmission of real 802.1Q-tagged traffic,
+because the switch does no longer parse those packets as VLAN after the TPID
+change.
+The TPID is restored when ``vlan_filtering`` is requested by the user through
+the bridge layer, and general IP termination becomes no longer possible through
+the switch netdevices in this mode.
+
+The switches have two programmable filters for link-local destination MACs.
+These are used to trap BPDUs and PTP traffic to the master netdevice, and are
+further used to support STP and 1588 ordinary clock/boundary clock
+functionality.
+
+The following traffic modes are supported over the switch netdevices:
+
++--------------------+------------+------------------+------------------+
+|                    | Standalone |   Bridged with   |   Bridged with   |
+|                    |    ports   | vlan_filtering 0 | vlan_filtering 1 |
++====================+============+==================+==================+
+| Regular traffic    |     Yes    |       Yes        |  No (use master) |
++--------------------+------------+------------------+------------------+
+| Management traffic |     Yes    |       Yes        |       Yes        |
+|    (BPDU, PTP)     |            |                  |                  |
++--------------------+------------+------------------+------------------+
+
 Switching features
 ==================
 
@@ -92,6 +124,23 @@ that VLAN awareness is global at the switch level is that once a bridge with
 ``vlan_filtering`` enslaves at least one switch port, the other un-bridged
 ports are no longer available for standalone traffic termination.
 
+Topology and loop detection through STP is supported.
+
+L2 FDB manipulation (add/delete/dump) is currently possible for the first
+generation devices. Aging time of FDB entries, as well as enabling fully static
+management (no address learning and no flooding of unknown traffic) is not yet
+configurable in the driver.
+
+Other notable features
+======================
+
+The switches have a PTP Hardware Clock that can be steered through SPI and used
+for timestamping management traffic on ingress and egress.
+Also, the T, Q and S devices support TTEthernet (an implementation of SAE
+AS6802 from TTTech), which is a set of Ethernet QoS enhancements somewhat
+similar in behavior to IEEE TSN (time-aware shaping, time-based policing).
+Configuring these features is currently not supported in the driver.
+
 Device Tree bindings and board design
 =====================================
 
-- 
2.17.1

Powered by blists - more mailing lists