| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20190724192549.24615-2-opensource@vdorst.com>
Date: Wed, 24 Jul 2019 21:25:47 +0200
From: René van Dorst <opensource@...rst.com>
To: netdev@...r.kernel.org
Cc: frank-w@...lic-files.de, sean.wang@...iatek.com,
f.fainelli@...il.com, linux@...linux.org.uk, davem@...emloft.net,
matthias.bgg@...il.com, andrew@...n.ch, vivien.didelot@...il.com,
john@...ozen.org, linux-mediatek@...ts.infradead.org,
linux-mips@...r.kernel.org, robh+dt@...nel.org,
devicetree@...r.kernel.org,
René van Dorst <opensource@...rst.com>
Subject: [PATCH net-next 1/3] net: dsa: mt7530: Convert to PHYLINK API
Convert mt7530 to PHYLINK API
Signed-off-by: René van Dorst <opensource@...rst.com>
rfc->v1:
* Renamed P5_MODE_* to P5_INTF_SEL_*. fits the function more
* Convert if-statement for speed bits to a switch suggested by
Daniel Santos
* Refactor flow_control pause bits and don't use state->link in
mt7530_phylink_mac_config() suggested by Russell King
* Move MAC tx/rx en/disable to mt7530_phylink_mac_link_up/down()
suggested by Russell King
* Always support PHY_INTERFACE_MODE_NA in mt7530_phylink_validate()
suggested by Russell King
* Added phylink_set_port_modes() in mt7530_phylink_validate() suggested
by Russell King
* Remove dev_err on the end of mt7530_phylink_mac_config() suggested by
Russell King
---
drivers/net/dsa/mt7530.c | 255 +++++++++++++++++++++++++++++----------
drivers/net/dsa/mt7530.h | 32 +++--
2 files changed, 203 insertions(+), 84 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 3181e95586d6..73a2204bf81a 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -13,7 +13,7 @@
#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include <linux/of_platform.h>
-#include <linux/phy.h>
+#include <linux/phylink.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/reset.h>
@@ -633,63 +633,6 @@ mt7530_get_sset_count(struct dsa_switch *ds, int port, int sset)
return ARRAY_SIZE(mt7530_mib);
}
-static void mt7530_adjust_link(struct dsa_switch *ds, int port,
- struct phy_device *phydev)
-{
- struct mt7530_priv *priv = ds->priv;
-
- if (phy_is_pseudo_fixed_link(phydev)) {
- dev_dbg(priv->dev, "phy-mode for master device = %x\n",
- phydev->interface);
-
- /* Setup TX circuit incluing relevant PAD and driving */
- mt7530_pad_clk_setup(ds, phydev->interface);
-
- if (priv->id == ID_MT7530) {
- /* Setup RX circuit, relevant PAD and driving on the
- * host which must be placed after the setup on the
- * device side is all finished.
- */
- mt7623_pad_clk_setup(ds);
- }
- } else {
- u16 lcl_adv = 0, rmt_adv = 0;
- u8 flowctrl;
- u32 mcr = PMCR_USERP_LINK | PMCR_FORCE_MODE;
-
- switch (phydev->speed) {
- case SPEED_1000:
- mcr |= PMCR_FORCE_SPEED_1000;
- break;
- case SPEED_100:
- mcr |= PMCR_FORCE_SPEED_100;
- break;
- }
-
- if (phydev->link)
- mcr |= PMCR_FORCE_LNK;
-
- if (phydev->duplex) {
- mcr |= PMCR_FORCE_FDX;
-
- if (phydev->pause)
- rmt_adv = LPA_PAUSE_CAP;
- if (phydev->asym_pause)
- rmt_adv |= LPA_PAUSE_ASYM;
-
- lcl_adv = linkmode_adv_to_lcl_adv_t(
- phydev->advertising);
- flowctrl = mii_resolve_flowctrl_fdx(lcl_adv, rmt_adv);
-
- if (flowctrl & FLOW_CTRL_TX)
- mcr |= PMCR_TX_FC_EN;
- if (flowctrl & FLOW_CTRL_RX)
- mcr |= PMCR_RX_FC_EN;
- }
- mt7530_write(priv, MT7530_PMCR_P(port), mcr);
- }
-}
-
static int
mt7530_cpu_port_enable(struct mt7530_priv *priv,
int port)
@@ -698,9 +641,6 @@ mt7530_cpu_port_enable(struct mt7530_priv *priv,
mt7530_write(priv, MT7530_PVC_P(port),
PORT_SPEC_TAG);
- /* Setup the MAC by default for the cpu port */
- mt7530_write(priv, MT7530_PMCR_P(port), PMCR_CPUP_LINK);
-
/* Disable auto learning on the cpu port */
mt7530_set(priv, MT7530_PSC_P(port), SA_DIS);
@@ -728,9 +668,6 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
mutex_lock(&priv->reg_mutex);
- /* Setup the MAC for the user port */
- mt7530_write(priv, MT7530_PMCR_P(port), PMCR_USERP_LINK);
-
/* Allow the user port gets connected to the cpu port and also
* restore the port matrix if the port is the member of a certain
* bridge.
@@ -739,7 +676,7 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
priv->ports[port].enable = true;
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
priv->ports[port].pm);
- mt7530_port_set_status(priv, port, 1);
+ mt7530_port_set_status(priv, port, 0);
mutex_unlock(&priv->reg_mutex);
@@ -1299,6 +1236,8 @@ mt7530_setup(struct dsa_switch *ds)
val |= MHWTRAP_MANUAL;
mt7530_write(priv, MT7530_MHWTRAP, val);
+ priv->p6_interface = PHY_INTERFACE_MODE_NA;
+
/* Enable and reset MIB counters */
mt7530_mib_reset(ds);
@@ -1323,6 +1262,186 @@ mt7530_setup(struct dsa_switch *ds)
return 0;
}
+static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct mt7530_priv *priv = ds->priv;
+ u32 mcr_cur, mcr_new;
+
+ switch (port) {
+ case 0: /* Internal phy */
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ if (state->interface != PHY_INTERFACE_MODE_GMII)
+ return;
+ break;
+ /* case 5: Port 5 is not supported! */
+ case 6: /* 1st cpu port */
+ if (state->interface != PHY_INTERFACE_MODE_RGMII &&
+ state->interface != PHY_INTERFACE_MODE_TRGMII)
+ return;
+
+ if (priv->p6_interface == state->interface)
+ break;
+ /* Setup TX circuit incluing relevant PAD and driving */
+ mt7530_pad_clk_setup(ds, state->interface);
+
+ if (priv->id == ID_MT7530) {
+ /* Setup RX circuit, relevant PAD and driving on the
+ * host which must be placed after the setup on the
+ * device side is all finished.
+ */
+ mt7623_pad_clk_setup(ds);
+ }
+ priv->p6_interface = state->interface;
+ break;
+ default:
+ dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+ return;
+ }
+
+ mcr_cur = mt7530_read(priv, MT7530_PMCR_P(port));
+ mcr_new = mcr_cur;
+ mcr_new &= ~(PMCR_FORCE_SPEED_1000 | PMCR_FORCE_SPEED_100 |
+ PMCR_FORCE_FDX | PMCR_TX_FC_EN | PMCR_RX_FC_EN);
+ mcr_new |= PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | PMCR_BACKOFF_EN |
+ PMCR_BACKPR_EN | PMCR_FORCE_MODE | PMCR_FORCE_LNK;
+
+ switch (state->speed) {
+ case SPEED_1000:
+ mcr_new |= PMCR_FORCE_SPEED_1000;
+ break;
+ case SPEED_100:
+ mcr_new |= PMCR_FORCE_SPEED_100;
+ break;
+ }
+ if (state->duplex == DUPLEX_FULL) {
+ mcr_new |= PMCR_FORCE_FDX;
+ if (state->pause & MLO_PAUSE_TX)
+ mcr_new |= PMCR_TX_FC_EN;
+ if (state->pause & MLO_PAUSE_RX)
+ mcr_new |= PMCR_RX_FC_EN;
+ }
+
+ if (mcr_new != mcr_cur)
+ mt7530_write(priv, MT7530_PMCR_P(port), mcr_new);
+}
+
+static void mt7530_phylink_mac_link_down(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ mt7530_port_set_status(priv, port, 0);
+}
+
+static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface,
+ struct phy_device *phydev)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ mt7530_port_set_status(priv, port, 1);
+}
+
+static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+
+ switch (port) {
+ case 0: /* Internal phy */
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
+ state->interface != PHY_INTERFACE_MODE_GMII)
+ goto unsupported;
+ break;
+ /* case 5: Port 5 not supported! */
+ case 6: /* 1st cpu port */
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
+ state->interface != PHY_INTERFACE_MODE_RGMII &&
+ state->interface != PHY_INTERFACE_MODE_TRGMII)
+ goto unsupported;
+ break;
+ default:
+ linkmode_zero(supported);
+ dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+ return;
+ }
+
+ phylink_set_port_modes(mask);
+ phylink_set(mask, Autoneg);
+
+ if (state->interface != PHY_INTERFACE_MODE_TRGMII) {
+ phylink_set(mask, 10baseT_Half);
+ phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
+ phylink_set(mask, 100baseT_Full);
+ phylink_set(mask, 1000baseT_Half);
+ }
+
+ phylink_set(mask, 1000baseT_Full);
+
+ phylink_set(mask, Pause);
+ phylink_set(mask, Asym_Pause);
+
+ linkmode_and(supported, supported, mask);
+ linkmode_and(state->advertising, state->advertising, mask);
+ return;
+
+unsupported:
+ linkmode_zero(supported);
+}
+
+static int
+mt7530_phylink_mac_link_state(struct dsa_switch *ds, int port,
+ struct phylink_link_state *state)
+{
+ struct mt7530_priv *priv = ds->priv;
+ u32 pmsr;
+
+ if (port < 0 || port >= MT7530_NUM_PORTS)
+ return -EINVAL;
+
+ pmsr = mt7530_read(priv, MT7530_PMSR_P(port));
+
+ state->link = (pmsr & PMSR_LINK);
+ state->an_complete = state->link;
+ state->duplex = !!(pmsr & PMSR_DPX);
+
+ switch (pmsr & PMSR_SPEED_MASK) {
+ case PMSR_SPEED_10:
+ state->speed = SPEED_10;
+ break;
+ case PMSR_SPEED_100:
+ state->speed = SPEED_100;
+ break;
+ case PMSR_SPEED_1000:
+ state->speed = SPEED_1000;
+ break;
+ default:
+ state->speed = SPEED_UNKNOWN;
+ break;
+ }
+
+ state->pause &= ~(MLO_PAUSE_RX | MLO_PAUSE_TX);
+ if (pmsr & PMSR_RX_FC)
+ state->pause |= MLO_PAUSE_RX;
+ if (pmsr & PMSR_TX_FC)
+ state->pause |= MLO_PAUSE_TX;
+
+ return 1;
+}
+
static const struct dsa_switch_ops mt7530_switch_ops = {
.get_tag_protocol = mtk_get_tag_protocol,
.setup = mt7530_setup,
@@ -1331,7 +1450,6 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
.phy_write = mt7530_phy_write,
.get_ethtool_stats = mt7530_get_ethtool_stats,
.get_sset_count = mt7530_get_sset_count,
- .adjust_link = mt7530_adjust_link,
.port_enable = mt7530_port_enable,
.port_disable = mt7530_port_disable,
.port_stp_state_set = mt7530_stp_state_set,
@@ -1344,6 +1462,11 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
.port_vlan_prepare = mt7530_port_vlan_prepare,
.port_vlan_add = mt7530_port_vlan_add,
.port_vlan_del = mt7530_port_vlan_del,
+ .phylink_validate = mt7530_phylink_validate,
+ .phylink_mac_link_state = mt7530_phylink_mac_link_state,
+ .phylink_mac_config = mt7530_phylink_mac_config,
+ .phylink_mac_link_down = mt7530_phylink_mac_link_down,
+ .phylink_mac_link_up = mt7530_phylink_mac_link_up,
};
static const struct of_device_id mt7530_of_match[] = {
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index bfac90f48102..107dd04acede 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -198,26 +198,20 @@ enum mt7530_vlan_port_attr {
#define PMCR_FORCE_SPEED_100 BIT(2)
#define PMCR_FORCE_FDX BIT(1)
#define PMCR_FORCE_LNK BIT(0)
-#define PMCR_COMMON_LINK (PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
- PMCR_BACKOFF_EN | PMCR_BACKPR_EN | \
- PMCR_TX_EN | PMCR_RX_EN | \
- PMCR_TX_FC_EN | PMCR_RX_FC_EN)
-#define PMCR_CPUP_LINK (PMCR_COMMON_LINK | PMCR_FORCE_MODE | \
- PMCR_FORCE_SPEED_1000 | \
- PMCR_FORCE_FDX | \
- PMCR_FORCE_LNK)
-#define PMCR_USERP_LINK PMCR_COMMON_LINK
-#define PMCR_FIXED_LINK (PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
- PMCR_FORCE_MODE | PMCR_TX_EN | \
- PMCR_RX_EN | PMCR_BACKPR_EN | \
- PMCR_BACKOFF_EN | \
- PMCR_FORCE_SPEED_1000 | \
- PMCR_FORCE_FDX | \
- PMCR_FORCE_LNK)
-#define PMCR_FIXED_LINK_FC (PMCR_FIXED_LINK | \
- PMCR_TX_FC_EN | PMCR_RX_FC_EN)
+#define PMCR_SPEED_MASK (PMCR_FORCE_SPEED_100 | \
+ PMCR_FORCE_SPEED_1000)
#define MT7530_PMSR_P(x) (0x3008 + (x) * 0x100)
+#define PMSR_EEE1G BIT(7)
+#define PMSR_EEE100M BIT(6)
+#define PMSR_RX_FC BIT(5)
+#define PMSR_TX_FC BIT(4)
+#define PMSR_SPEED_1000 BIT(3)
+#define PMSR_SPEED_100 BIT(2)
+#define PMSR_SPEED_10 0x00
+#define PMSR_SPEED_MASK (PMSR_SPEED_100 | PMSR_SPEED_1000)
+#define PMSR_DPX BIT(1)
+#define PMSR_LINK BIT(0)
/* Register for MIB */
#define MT7530_PORT_MIB_COUNTER(x) (0x4000 + (x) * 0x100)
@@ -423,6 +417,7 @@ struct mt7530_port {
* @ports: Holding the state among ports
* @reg_mutex: The lock for protecting among process accessing
* registers
+ * @p6_interface Holding the current port 6 interface
*/
struct mt7530_priv {
struct device *dev;
@@ -435,6 +430,7 @@ struct mt7530_priv {
struct gpio_desc *reset;
unsigned int id;
bool mcm;
+ phy_interface_t p6_interface;
struct mt7530_port ports[MT7530_NUM_PORTS];
/* protect among processes for registers access*/
--
2.20.1
Powered by blists - more mailing lists