netdev - Re: [PATCH 05/16] net: phy: adin: configure RGMII/RMII/MII modes on config

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20190805143935.GM24275@lunn.ch>
Date:   Mon, 5 Aug 2019 16:39:35 +0200
From:   Andrew Lunn <andrew@...n.ch>
To:     Alexandru Ardelean <alexandru.ardelean@...log.com>
Cc:     netdev@...r.kernel.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org, davem@...emloft.net,
        robh+dt@...nel.org, mark.rutland@....com, f.fainelli@...il.com,
        hkallweit1@...il.com
Subject: Re: [PATCH 05/16] net: phy: adin: configure RGMII/RMII/MII modes on
 config

On Mon, Aug 05, 2019 at 07:54:42PM +0300, Alexandru Ardelean wrote:
> The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
> unconfigured) is RGMII.
> This change adds support for configuring these modes via the device
> registers.
> 
> For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),

It would be nice to add the missing space.

> the default delay is 2 ns. This can be configurable and will be done in
> a subsequent change.
> 
> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@...log.com>
> ---
>  drivers/net/phy/adin.c | 79 +++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 78 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
> index 3dd9fe50f4c8..dbdb8f60741c 100644
> --- a/drivers/net/phy/adin.c
> +++ b/drivers/net/phy/adin.c
> @@ -33,14 +33,91 @@
>  	 ADIN1300_INT_HW_IRQ_EN)
>  #define ADIN1300_INT_STATUS_REG			0x0019
>  
> +#define ADIN1300_GE_RGMII_CFG_REG		0xff23
> +#define   ADIN1300_GE_RGMII_RXID_EN		BIT(2)
> +#define   ADIN1300_GE_RGMII_TXID_EN		BIT(1)
> +#define   ADIN1300_GE_RGMII_EN			BIT(0)
> +
> +#define ADIN1300_GE_RMII_CFG_REG		0xff24
> +#define   ADIN1300_GE_RMII_EN			BIT(0)
> +
> +static int adin_config_rgmii_mode(struct phy_device *phydev,
> +				  phy_interface_t intf)
> +{
> +	int reg;
> +
> +	reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_RGMII_CFG_REG);
> +	if (reg < 0)
> +		return reg;
> +
> +	if (!phy_interface_mode_is_rgmii(intf)) {
> +		reg &= ~ADIN1300_GE_RGMII_EN;
> +		goto write;
> +	}
> +
> +	reg |= ADIN1300_GE_RGMII_EN;
> +
> +	if (intf == PHY_INTERFACE_MODE_RGMII_ID ||
> +	    intf == PHY_INTERFACE_MODE_RGMII_RXID) {
> +		reg |= ADIN1300_GE_RGMII_RXID_EN;
> +	} else {
> +		reg &= ~ADIN1300_GE_RGMII_RXID_EN;
> +	}
> +
> +	if (intf == PHY_INTERFACE_MODE_RGMII_ID ||
> +	    intf == PHY_INTERFACE_MODE_RGMII_TXID) {
> +		reg |= ADIN1300_GE_RGMII_TXID_EN;
> +	} else {
> +		reg &= ~ADIN1300_GE_RGMII_TXID_EN;
> +	}

Nice. Often driver writers forget to clear the delay, they only set
it. Not so here.

However, is checkpatch happy with this? Each half of the if/else is a
single statement, so the {} are not needed.

> +
> +write:
> +	return phy_write_mmd(phydev, MDIO_MMD_VEND1,
> +			     ADIN1300_GE_RGMII_CFG_REG, reg);
> +}
> +
> +static int adin_config_rmii_mode(struct phy_device *phydev,
> +				 phy_interface_t intf)
> +{
> +	int reg;
> +
> +	reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_RMII_CFG_REG);
> +	if (reg < 0)
> +		return reg;
> +
> +	if (intf != PHY_INTERFACE_MODE_RMII) {
> +		reg &= ~ADIN1300_GE_RMII_EN;
> +		goto write;

goto? Really?

> +	}
> +
> +	reg |= ADIN1300_GE_RMII_EN;
> +
> +write:
> +	return phy_write_mmd(phydev, MDIO_MMD_VEND1,
> +			     ADIN1300_GE_RMII_CFG_REG, reg);
> +}
> +
>  static int adin_config_init(struct phy_device *phydev)
>  {
> -	int rc;
> +	phy_interface_t interface, rc;

genphy_config_init() does not return a phy_interface_t!

>  
>  	rc = genphy_config_init(phydev);
>  	if (rc < 0)
>  		return rc;
>  
> +	interface = phydev->interface;
> +
> +	rc = adin_config_rgmii_mode(phydev, interface);
> +	if (rc < 0)
> +		return rc;
> +
> +	rc = adin_config_rmii_mode(phydev, interface);
> +	if (rc < 0)
> +		return rc;
> +
> +	dev_info(&phydev->mdio.dev, "PHY is using mode '%s'\n",
> +		 phy_modes(phydev->interface));

phydev_dbg(), or not at all.

	      Andrew