[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Date: Thu, 8 Aug 2019 09:26:26 +0100
From: Russell King - ARM Linux admin <linux@...linux.org.uk>
To: Jose Abreu <Jose.Abreu@...opsys.com>
Cc: "netdev@...r.kernel.org" <netdev@...r.kernel.org>,
Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Heiner Kallweit <hkallweit1@...il.com>
Subject: Re: Clause 73 and USXGMII
Hi,
Have you tried enabling debug mode in phylink (add #define DEBUG at the
top of the file) ?
Thanks.
On Thu, Aug 08, 2019 at 08:17:29AM +0000, Jose Abreu wrote:
> ++ PHY Experts
>
> From: Jose Abreu <joabreu@...opsys.com>
> Date: Aug/07/2019, 16:46:23 (UTC+00:00)
>
> > Hello,
> >
> > I've some sample code for Clause 73 support using Synopsys based XPCS
> > but I would like to clarify some things that I noticed.
> >
> > I'm using USXGMII as interface and a single SERDES that operates at 10G
> > rate but MAC side is working at 2.5G. Maximum available bandwidth is
> > therefore 2.5Gbps.
> >
> > So, I configure USXGMII for 2.5G mode and it works but if I try to limit
> > the autoneg abilities to 2.5G max then it never finishes:
> > # ethtool enp4s0
> > Settings for enp4s0:
> > Supported ports: [ ]
> > Supported link modes: 1000baseKX/Full
> > 2500baseX/Full
> > Supported pause frame use: Symmetric Receive-only
> > Supports auto-negotiation: Yes
> > Supported FEC modes: Not reported
> > Advertised link modes: 1000baseKX/Full
> > 2500baseX/Full
> > Advertised pause frame use: Symmetric Receive-only
> > Advertised auto-negotiation: Yes
> > Advertised FEC modes: Not reported
> > Speed: Unknown!
> > Duplex: Unknown! (255)
> > Port: MII
> > PHYAD: 0
> > Transceiver: internal
> > Auto-negotiation: on
> > Supports Wake-on: ug
> > Wake-on: d
> > Current message level: 0x0000003f (63)
> > drv probe link timer ifdown ifup
> > Link detected: no
> >
> > When I do not limit autoneg and I say that maximum limit is 10G then I
> > get Link Up and autoneg finishes with this outcome:
> > # ethtool enp4s0
> > Settings for enp4s0:
> > Supported ports: [ ]
> > Supported link modes: 1000baseKX/Full
> > 2500baseX/Full
> > 10000baseKX4/Full
> > 10000baseKR/Full
> > Supported pause frame use: Symmetric Receive-only
> > Supports auto-negotiation: Yes
> > Supported FEC modes: Not reported
> > Advertised link modes: 1000baseKX/Full
> > 2500baseX/Full
> > 10000baseKX4/Full
> > 10000baseKR/Full
> > Advertised pause frame use: Symmetric Receive-only
> > Advertised auto-negotiation: Yes
> > Advertised FEC modes: Not reported
> > Link partner advertised link modes: 1000baseKX/Full
> > 2500baseX/Full
> > 10000baseKX4/Full
> > 10000baseKR/Full
> > Link partner advertised pause frame use: Symmetric Receive-only
> > Link partner advertised auto-negotiation: Yes
> > Link partner advertised FEC modes: Not reported
> > Speed: 2500Mb/s
> > Duplex: Full
> > Port: MII <- Never mind this, it's a SW issue
> > PHYAD: 0
> > Transceiver: internal
> > Auto-negotiation: on
> > Supports Wake-on: ug
> > Wake-on: d
> > Current message level: 0x0000003f (63)
> > drv probe link timer ifdown ifup
> > Link detected: yes
> >
> > I was expecting that, as MAC side is limited to 2.5G, I should set in
> > phylink the correct capabilities and then outcome of autoneg would only
> > have up to 2.5G modes. Am I wrong ?
> >
> > ---
> > Thanks,
> > Jose Miguel Abreu
>
>
> ---
> Thanks,
> Jose Miguel Abreu
>
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
Powered by blists - more mailing lists