| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <5AC684B1-79CA-41EB-9553-FFBFD7284085@gmail.com>
Date: Fri, 4 Oct 2019 14:53:15 +0100
From: Rudolf Spring <rudolf.spring@...il.com>
To: Siva Reddy Kallam <siva.kallam@...adcom.com>
Cc: Michael Chan <michael.chan@...adcom.com>,
Netdev <netdev@...r.kernel.org>
Subject: Re: Gentoo Linux 5.x - Tigon3
With Kernel 5.3.2. Interesting all are tx_mac_errors.
ifconfig eth0
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 9000
ether a8:20:66:28:e6:95 txqueuelen 1000 (Ethernet)
RX packets 1649204 bytes 775261068 (739.3 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1144621 bytes 1241414276 (1.1 GiB)
TX errors 369 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 16
ethtool -S eth0
NIC statistics:
rx_octets: 752756285
rx_fragments: 0
rx_ucast_packets: 1132211
rx_mcast_packets: 128115
rx_bcast_packets: 372162
rx_fcs_errors: 0
rx_align_errors: 0
rx_xon_pause_rcvd: 0
rx_xoff_pause_rcvd: 0
rx_mac_ctrl_rcvd: 0
rx_xoff_entered: 0
rx_frame_too_long_errors: 0
rx_jabbers: 0
rx_undersize_packets: 0
rx_in_length_errors: 0
rx_out_length_errors: 0
rx_64_or_less_octet_packets: 0
rx_65_to_127_octet_packets: 0
rx_128_to_255_octet_packets: 0
rx_256_to_511_octet_packets: 0
rx_512_to_1023_octet_packets: 0
rx_1024_to_1522_octet_packets: 0
rx_1523_to_2047_octet_packets: 0
rx_2048_to_4095_octet_packets: 0
rx_4096_to_8191_octet_packets: 0
rx_8192_to_9022_octet_packets: 0
tx_octets: 1236703101
tx_collisions: 0
tx_xon_sent: 0
tx_xoff_sent: 0
tx_flow_control: 0
tx_mac_errors: 369
tx_single_collisions: 0
tx_mult_collisions: 0
tx_deferred: 0
tx_excessive_collisions: 0
tx_late_collisions: 0
tx_collide_2times: 0
tx_collide_3times: 0
tx_collide_4times: 0
tx_collide_5times: 0
tx_collide_6times: 0
tx_collide_7times: 0
tx_collide_8times: 0
tx_collide_9times: 0
tx_collide_10times: 0
tx_collide_11times: 0
tx_collide_12times: 0
tx_collide_13times: 0
tx_collide_14times: 0
tx_collide_15times: 0
tx_ucast_packets: 986854
tx_mcast_packets: 146951
tx_bcast_packets: 1117
tx_carrier_sense_errors: 0
tx_discards: 0
tx_errors: 0
dma_writeq_full: 0
dma_write_prioq_full: 0
rxbds_empty: 0
rx_discards: 0
rx_errors: 0
rx_threshold_hit: 0
dma_readq_full: 0
dma_read_prioq_full: 0
tx_comp_queue_full: 0
ring_set_send_prod_index: 0
ring_status_update: 0
nic_irqs: 0
nic_avoided_irqs: 0
nic_tx_threshold_hit: 0
mbuf_lwm_thresh_hit: 0
> On 4 Oct 2019, at 12:52, Siva Reddy Kallam <siva.kallam@...adcom.com> wrote:
>
>
>
> On Wed, Oct 2, 2019 at 10:05 PM Rudolf Spring <rudolf.spring@...il.com> wrote:
> The output of dmesg and ethtool is identical between 4.19.72 and 5.3.2. Any suggestions ?
> Can you please provide the output of "ethtool -S eth0" command?
> In the mean time, I will review the register dump and also try to reproduce in our lab.
> 0000:01:00.0: enabling device (0000 -> 0002)
> [ 1.140738] tg3 0000:01:00.0 eth0: Tigon3 [partno(BCM957766a) rev 57766001] (PCI Express) MAC address a8:20:66:28:e6:95
> [ 1.140741] tg3 0000:01:00.0 eth0: attached PHY is 57765 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
> [ 1.140743] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
> [ 1.140744] tg3 0000:01:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit]
> [ 10.290239] tg3 0000:01:00.0 eth0: Link is up at 1000 Mbps, full duplex
> [ 10.290241] tg3 0000:01:00.0 eth0: Flow control is on for TX and on for RX
> [ 10.290242] tg3 0000:01:00.0 eth0: EEE is enabled
>
> ethtool eth0
> Settings for eth0:
> Supported ports: [ TP ]
> Supported link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> 1000baseT/Half 1000baseT/Full
> Supported pause frame use: No
> Supports auto-negotiation: Yes
> Supported FEC modes: Not reported
> Advertised link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> 1000baseT/Half 1000baseT/Full
> Advertised pause frame use: Symmetric
> Advertised auto-negotiation: Yes
> Advertised FEC modes: Not reported
> Link partner advertised link modes: 10baseT/Half 10baseT/Full
> 100baseT/Half 100baseT/Full
> 1000baseT/Full
> Link partner advertised pause frame use: Symmetric
> Link partner advertised auto-negotiation: Yes
> Link partner advertised FEC modes: Not reported
> Speed: 1000Mb/s
> Duplex: Full
> Port: Twisted Pair
> PHYAD: 1
> Transceiver: internal
> Auto-negotiation: on
> MDI-X: off
> Supports Wake-on: g
> Wake-on: g
> Current message level: 0x000000ff (255)
> drv probe link timer ifdown ifup rx_err tx_err
> Link detected: yes
>
> ethtool -a eth0
> Pause parameters for eth0:
> Autonegotiate: on
> RX: on
> TX: on
> RX negotiated: on
> TX negotiated: on
>
> ethtool -g eth0
> Ring parameters for eth0:
> Pre-set maximums:
> RX: 511
> RX Mini: 0
> RX Jumbo: 255
> TX: 511
> Current hardware settings:
> RX: 200
> RX Mini: 0
> RX Jumbo: 100
> TX: 511
>
> ethtool -c eth0
> Coalesce parameters for eth0:
> Adaptive RX: off TX: off
> stats-block-usecs: 0
> sample-interval: 0
> pkt-rate-low: 0
> pkt-rate-high: 0
>
> rx-usecs: 20
> rx-frames: 5
> rx-usecs-irq: 0
> rx-frames-irq: 5
>
> tx-usecs: 72
> tx-frames: 53
> tx-usecs-irq: 0
> tx-frames-irq: 5
>
> rx-usecs-low: 0
> rx-frame-low: 0
> tx-usecs-low: 0
> tx-frame-low: 0
>
> rx-usecs-high: 0
> rx-frame-high: 0
> tx-usecs-high: 0
> tx-frame-high: 0
>
> ethtool -k eth0
> Features for eth0:
> rx-checksumming: on
> tx-checksumming: on
> tx-checksum-ipv4: on
> tx-checksum-ip-generic: off [fixed]
> tx-checksum-ipv6: on
> tx-checksum-fcoe-crc: off [fixed]
> tx-checksum-sctp: off [fixed]
> scatter-gather: on
> tx-scatter-gather: on
> tx-scatter-gather-fraglist: off [fixed]
> tcp-segmentation-offload: on
> tx-tcp-segmentation: on
> tx-tcp-ecn-segmentation: on
> tx-tcp-mangleid-segmentation: off
> tx-tcp6-segmentation: on
> udp-fragmentation-offload: off
> generic-segmentation-offload: on
> generic-receive-offload: on
> large-receive-offload: off [fixed]
> rx-vlan-offload: on [fixed]
> tx-vlan-offload: on [fixed]
> ntuple-filters: off [fixed]
> receive-hashing: off [fixed]
> highdma: on
> rx-vlan-filter: off [fixed]
> vlan-challenged: off [fixed]
> tx-lockless: off [fixed]
> netns-local: off [fixed]
> tx-gso-robust: off [fixed]
> tx-fcoe-segmentation: off [fixed]
> tx-gre-segmentation: off [fixed]
> tx-gre-csum-segmentation: off [fixed]
> tx-ipxip4-segmentation: off [fixed]
> tx-ipxip6-segmentation: off [fixed]
> tx-udp_tnl-segmentation: off [fixed]
> tx-udp_tnl-csum-segmentation: off [fixed]
> tx-gso-partial: off [fixed]
> tx-sctp-segmentation: off [fixed]
> tx-esp-segmentation: off [fixed]
> tx-udp-segmentation: off [fixed]
> fcoe-mtu: off [fixed]
> tx-nocache-copy: off
> loopback: off [fixed]
> rx-fcs: off [fixed]
> rx-all: off [fixed]
> tx-vlan-stag-hw-insert: off [fixed]
> rx-vlan-stag-hw-parse: off [fixed]
> rx-vlan-stag-filter: off [fixed]
> l2-fwd-offload: off [fixed]
> hw-tc-offload: off [fixed]
> esp-hw-offload: off [fixed]
> esp-tx-csum-hw-offload: off [fixed]
> rx-udp_tunnel-port-offload: off [fixed]
> tls-hw-tx-offload: off [fixed]
> tls-hw-rx-offload: off [fixed]
> rx-gro-hw: off [fixed]
> tls-hw-record: off [fixed]
>
> ethtool -n eth0
> 4 RX rings available
> rxclass: Cannot get RX class rule count: Operation not supported
> RX classification rule retrieval failed
>
> ethtool -t eth0
> The test result is PASS
> The test extra info:
> nvram test (online) 0
> link test (online) 0
> register test (offline) 0
> memory test (offline) 0
> mac loopback test (offline) 0
> phy loopback test (offline) 0
> ext loopback test (offline) 0
> interrupt test (offline) 0
>
> ethtool -T eth0
> Time stamping parameters for eth0:
> Capabilities:
> software-transmit (SOF_TIMESTAMPING_TX_SOFTWARE)
> software-receive (SOF_TIMESTAMPING_RX_SOFTWARE)
> software-system-clock (SOF_TIMESTAMPING_SOFTWARE)
> PTP Hardware Clock: none
> Hardware Transmit Timestamp Modes:
> off (HWTSTAMP_TX_OFF)
> on (HWTSTAMP_TX_ON)
> Hardware Receive Filter Modes:
> none (HWTSTAMP_FILTER_NONE)
> ptpv1-l4-event (HWTSTAMP_FILTER_PTP_V1_L4_EVENT)
> ptpv2-l4-event (HWTSTAMP_FILTER_PTP_V2_L4_EVENT)
> ptpv2-l2-event (HWTSTAMP_FILTER_PTP_V2_L2_EVENT)
>
> ethtool -l eth0
> Channel parameters for eth0:
> Pre-set maximums:
> RX: 4
> TX: 1
> Other: 0
> Combined: 0
> Current hardware settings:
> RX: 4
> TX: 1
> Other: 0
> Combined: 0
>
> ethtool --show-eee eth0
> EEE Settings for eth0:
> EEE status: enabled - active
> Tx LPI: 2047 (us)
> Supported EEE link modes: 100baseT/Full
> 1000baseT/Full
> Advertised EEE link modes: 100baseT/Full
> 1000baseT/Full
> Link partner advertised EEE link modes: 100baseT/Full
> 1000baseT/Full
>
> > These are all the tg3 changes between 4.19 and 5.0:
> >
> > 750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
> > cddaf02bcb73 tg3: optionally use eth_platform_get_mac_address() to get
> > mac address
> > 3c1bcc8614db net: ethernet: Convert phydev advertize and supported
> > from u32 to link mode
> > 6fe42e228dc2 tg3: extend PTP gettime function to read system clock
> > 310fc0513ea9 tg3: Fix fall-through annotations
> > 22b7d29926b5 net: ethernet: Add helper to determine if pause
> > configuration is supported
> > 70814e819c11 net: ethernet: Add helper for set_pauseparam for Asym Pause
> > af8d9bb2f2f4 net: ethernet: Add helper for MACs which support asym pause
> > 04b7d41d8046 net: ethernet: Fix up drivers masking pause support
> > 58056c1e1b0e net: ethernet: Use phy_set_max_speed() to limit advertised speed
> >
> > Most of the changes are related to PHY settings. I suggest that you
> > check the link settings, including speed, pause, asym pause, etc
> > between the working kernel and the non-working kernel to see if there
> > are differences in the settings.
>
Powered by blists - more mailing lists