netdev - [PATCH RFC V2 6/6] ARM: dts: bcm2711-rpi-4: Enable GENET support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <1572702093-18261-7-git-send-email-wahrenst@gmx.net>
Date:   Sat,  2 Nov 2019 14:41:33 +0100
From:   Stefan Wahren <wahrenst@....net>
To:     Matthias Brugger <matthias.bgg@...nel.org>,
        Matthias Brugger <mbrugger@...e.com>,
        "David S . Miller" <davem@...emloft.net>,
        Florian Fainelli <f.fainelli@...il.com>
Cc:     Eric Anholt <eric@...olt.net>,
        Nicolas Saenz Julienne <nsaenzjulienne@...e.de>,
        Doug Berger <opendmb@...il.com>, netdev@...r.kernel.org,
        bcm-kernel-feedback-list@...adcom.com,
        linux-arm-kernel@...ts.infradead.org,
        Stefan Wahren <wahrenst@....net>
Subject: [PATCH RFC V2 6/6] ARM: dts: bcm2711-rpi-4: Enable GENET support

This enables the Gigabit Ethernet support on the Raspberry Pi 4.
The defined PHY mode is equivalent to the default register settings
in the downstream tree.

Signed-off-by: Stefan Wahren <wahrenst@....net>
Signed-off-by: Matthias Brugger <mbrugger@...e.com>
---
 arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 23 +++++++++++++++++++++++
 arch/arm/boot/dts/bcm2711.dtsi        | 19 +++++++++++++++++++
 2 files changed, 42 insertions(+)

diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
index cccc1cc..904efe1 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@@ -19,6 +19,10 @@
 		reg = <0 0 0>;
 	};

+	aliases {
+		ethernet0 = &genet;
+	};
+
 	leds {
 		act {
 			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
@@ -97,6 +101,25 @@
 	status = "okay";
 };

+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+
+	mdio@e14 {
+		compatible = "brcm,genet-mdio-v5";
+		reg = <0xe14 0x8>;
+		reg-names = "mdio";
+		#address-cells = <0x0>;
+		#size-cells = <0x1>;
+
+		phy1: ethernet-phy@1 {
+			/* No PHY interrupt */
+			reg = <0x1>;
+		};
+	};
+};
+
 /* uart0 communicates with the BT module */
 &uart0 {
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
index ac83dac..ff24396 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@@ -305,6 +305,25 @@
 			cpu-release-addr = <0x0 0x000000f0>;
 		};
 	};
+
+	scb {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>;
+
+		genet: ethernet@...80000 {
+			compatible = "brcm,genet-v5";
+			reg = <0x0 0x7d580000 0x10000>;
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			dma-burst-sz = <0x08>;
+			status = "disabled";
+		};
+	};
 };

 &clk_osc {
--
2.7.4