Message-ID: <2b2d0e14-59c7-5efa-93a8-8027f4ed43e5@mellanox.com>
Date:   Sun, 19 Jan 2020 14:52:53 +0000
From:   Maor Gottlieb <maorg@...lanox.com>
To:     Jay Vosburgh <jay.vosburgh@...onical.com>
CC:     Andy Gospodarek <andy@...yhouse.net>,
        Jiri Pirko <jiri@...nulli.us>,
        "vfalico@...il.com" <vfalico@...il.com>,
        "netdev@...r.kernel.org" <netdev@...r.kernel.org>,
        Saeed Mahameed <saeedm@...lanox.com>,
        Jason Gunthorpe <jgg@...lanox.com>,
        Leon Romanovsky <leonro@...lanox.com>,
        Jiri Pirko <jiri@...lanox.com>,
        Alex Rosenbaum <alexr@...lanox.com>,
        "davem@...emloft.net" <davem@...emloft.net>,
        Mark Zhang <markz@...lanox.com>,
        Parav Pandit <parav@...lanox.com>
Subject: Re: Expose bond_xmit_hash function


On 1/16/2020 6:00 PM, Jay Vosburgh wrote:
> Maor Gottlieb <maorg@...lanox.com> wrote:
>
>> On 1/16/2020 4:42 PM, Andy Gospodarek wrote:
>>> On Wed, Jan 15, 2020 at 03:15:35PM +0100, Jiri Pirko wrote:
>>>> Wed, Jan 15, 2020 at 02:04:49PM CET, maorg@...lanox.com wrote:
>>>>> On 1/15/2020 11:45 AM, Jiri Pirko wrote:
>>>>>> Wed, Jan 15, 2020 at 09:01:43AM CET, maorg@...lanox.com wrote:
>>>>>>> RDMA over Converged Ethernet (RoCE) is a standard protocol which enables
>>>>>>> RDMA’s efficient data transfer over Ethernet networks allowing transport
>>>>>>> offload with hardware RDMA engine implementation.
>>>>>>> The RoCE v2 protocol exists on top of either the UDP/IPv4 or the
>>>>>>> UDP/IPv6 protocol:
>>>>>>>
>>>>>>> --------------------------------------------------------------
>>>>>>> | L2 | L3 | UDP |IB BTH | Payload| ICRC | FCS |
>>>>>>> --------------------------------------------------------------
>>>>>>>
>>>>>>> When a bond LAG netdev is in use, we would like to have the same hash
>>>>>>> result for RoCE packets as any other UDP packets, for this purpose we
>>>>>>> need to expose the bond_xmit_hash function to external modules.
>>>>>>> If no objection, I will push a patch that export this symbol.
>>>>>> I don't think it is good idea to do it. It is an internal bond function.
>>>>>> it even accepts "struct bonding *bond". Do you plan to push netdev
>>>>>> struct as an arg instead? What about team? What about OVS bonding?
>>>>> No, I am planning to pass the bond struct as an arg. Currently, team
>>>> Hmm, that would be ofcourse wrong, as it is internal bonding driver
>>>> structure.
>>>>
>>>>
>>>>> bonding is not supported in RoCE LAG and I don't see how OVS is related.
>>>> Should work for all. OVS is related in a sense that you can do bonding
>>>> there too.
>>>>
>>>>
>>>>>> Also, you don't really need a hash, you need a slave that is going to be
>>>>>> used for a packet xmit.
>>>>>>
>>>>>> I think this could work in a generic way:
>>>>>>
>>>>>> struct net_device *master_xmit_slave_get(struct net_device *master_dev,
>>>>>> 					 struct sk_buff *skb);
>>>>> The suggestion is to put this function in the bond driver and call it
>>>>> instead of bond_xmit_hash? is it still necessary if I have the bond pointer?
>>>> No. This should be in a generic code. No direct calls down to bonding
>>>> driver please. Or do you want to load bonding module every time your
>>>> module loads?
>>>>
>>>> I thinks this can be implemented with ndo with "master_xmit_slave_get()"
>>>> as a wrapper. Masters that support this would just implement the ndo.
>>> In general I think this is a good idea (though maybe not with an skb as
>>> an arg so we can use it easily within BPF), but I'm not sure if solves
>>> the problem that Maor et al were setting out to solve.
>>>
>>> Maor, if you did export bond_xmit_hash() to be used by another driver,
>>> you would presumably have a check in place so if the RoCE and UDP
>>> packets had a different hash function output you would make a change and
>>> be sure that the UDP frames would go out on the same device that the
>>> RoCE traffic would normally use.  Is this correct?  Would you also send
>>> the frames directly on the interface using dev_queue_xmit() and bypass
>>> the bonding driver completely?
>> RoCE packets are UDP. The idea is that the same UDP header (RoCE as
>> well) will get the same hash result so they will be transmitted from the
>> same port.
>> The frames will be sent by using the RDMA send API and bypass the
>> bonding driver completely.
>> Is it answer your question?
> 	If the RDMA send bypasses bonding, how will you insure that the
> same hash result maps to the same underlying interface for both bonding
> and RDMA?
>
> 	-J

In RoCE, the affinity is determined while the HW resources are created 
and will be modified globally in run time to track the active salves.
If we get the slave result, all the UDP packets will have the same 
affinity as RoCE.
The downside is that all RoCE HW resources will be stuck with the 
original affinity port and not move to the re-activate slave once it 
goes up. Another disadvantage, when both ports are down, we still need 
to create the RoCE HW resources with a given port affinity. Both 
problems are solved by exporting the hash.

>
>>> I don't think I fundamentally have a problem with this, I just want to
>>> make sure I understand your proposed code-flow.
>>>
>>> Thanks!
>>>
> ---
> 	-Jay Vosburgh, jay.vosburgh@...onical.com

Powered by blists - more mailing lists