| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200219151259.14273-4-olteanv@gmail.com>
Date: Wed, 19 Feb 2020 17:12:57 +0200
From: Vladimir Oltean <olteanv@...il.com>
To: shawnguo@...nel.org, robh+dt@...nel.org, mark.rutland@....com,
devicetree@...r.kernel.org, davem@...emloft.net,
netdev@...r.kernel.org
Cc: andrew@...n.ch, vivien.didelot@...il.com, f.fainelli@...il.com,
linux-kernel@...r.kernel.org
Subject: [PATCH v2 net-next/devicetree 3/5] dt-bindings: net: dsa: ocelot: document the vsc9959 core
From: Vladimir Oltean <vladimir.oltean@....com>
This patch adds the required documentation for the embedded L2 switch
inside the NXP LS1028A chip.
I've submitted it in the legacy format instead of yaml schema, because
DSA itself has not yet been converted to yaml, and this driver defines
no custom bindings.
Signed-off-by: Vladimir Oltean <vladimir.oltean@....com>
---
Changes in v2:
Adapted phy-mode = "gmii" to phy-mode = "internal".
.../devicetree/bindings/net/dsa/ocelot.txt | 96 +++++++++++++++++++
1 file changed, 96 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/dsa/ocelot.txt
diff --git a/Documentation/devicetree/bindings/net/dsa/ocelot.txt b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
new file mode 100644
index 000000000000..a9d86e09dafa
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/ocelot.txt
@@ -0,0 +1,96 @@
+Microchip Ocelot switch driver family
+=====================================
+
+Felix
+-----
+
+The VSC9959 core is currently the only switch supported by the driver, and is
+found in the NXP LS1028A. It is a PCI device, part of the larger ENETC root
+complex. As a result, the ethernet-switch node is a sub-node of the PCIe root
+complex node and its "reg" property conforms to the parent node bindings:
+
+* reg: Specifies PCIe Device Number and Function Number of the endpoint device,
+ in this case for the Ethernet L2Switch it is PF5 (of device 0, bus 0).
+
+It does not require a "compatible" string.
+
+The interrupt line is used to signal availability of PTP TX timestamps and for
+TSN frame preemption.
+
+For the external switch ports, depending on board configuration, "phy-mode" and
+"phy-handle" are populated by board specific device tree instances. Ports 4 and
+5 are fixed as internal ports in the NXP LS1028A instantiation.
+
+Any port can be disabled, but the CPU port should be kept enabled.
+
+The CPU port property ("ethernet"), which is assigned by default to the 2.5Gbps
+port@4, can be moved to the 1Gbps port@5, depending on the specific use case.
+DSA tagging is supported on a single port at a time.
+
+For the rest of the device tree binding definitions, which are standard DSA and
+PCI, refer to the following documents:
+
+Documentation/devicetree/bindings/net/dsa/dsa.txt
+Documentation/devicetree/bindings/pci/pci.txt
+
+Example:
+
+&soc {
+ pcie@...000000 { /* Integrated Endpoint Root Complex */
+ ethernet-switch@0,5 {
+ reg = <0x000500 0 0 0 0>;
+ /* IEP INT_B */
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* External ports */
+ port@0 {
+ reg = <0>;
+ label = "swp0";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "swp1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "swp2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "swp3";
+ };
+
+ /* Tagging CPU port */
+ port@4 {
+ reg = <4>;
+ ethernet = <&enetc_port2>;
+ phy-mode = "internal";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ };
+ };
+
+ /* Non-tagging CPU port */
+ port@5 {
+ reg = <5>;
+ phy-mode = "internal";
+ status = "disabled";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+};
--
2.17.1
Powered by blists - more mailing lists