netdev - [PATCH v3 devicetree 3/6] net: dsa: felix: Use PHY_INTERFACE_MODE

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Date:   Sun, 23 Feb 2020 22:47:13 +0200
From:   Vladimir Oltean <olteanv@...il.com>
To:     shawnguo@...nel.org, robh+dt@...nel.org, mark.rutland@....com,
        devicetree@...r.kernel.org
Cc:     andrew@...n.ch, vivien.didelot@...il.com, f.fainelli@...il.com,
        alexandru.marginean@....com, claudiu.manoil@....com,
        michael@...le.cc, davem@...emloft.net, netdev@...r.kernel.org,
        linux-kernel@...r.kernel.org
Subject: [PATCH v3 devicetree 3/6] net: dsa: felix: Use PHY_INTERFACE_MODE_INTERNAL instead of GMII

From: Vladimir Oltean <vladimir.oltean@....com>

phy-mode = "gmii" is confusing because it may mean that the port
supports the 8-bit-wide parallel data interface pinout, which it
doesn't.

It may also be confusing because one of the "gmii" internal ports is
actually overclocked to run at 2.5Gbps (even though, yes, as far as the
switch MAC is concerned, it still thinks it's gigabit).

So use the phy-mode = "internal" property to describe the internal ports
inside the NXP LS1028A chip (the ones facing the ENETC). The change
should be fine, because the device tree bindings document is yet to be
introduced, and there are no stable DT blobs in use.

Signed-off-by: Vladimir Oltean <vladimir.oltean@....com>
Reviewed-by: Andrew Lunn <andrew@...n.ch>
Tested-by: Michael Walle <michael@...le.cc>
---
Changes in v3:
None.

Changes in v2:
Patch is new.

 drivers/net/dsa/ocelot/felix.c         | 3 +--
 drivers/net/dsa/ocelot/felix_vsc9959.c | 3 +--
 2 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
index 3257962c147e..35124ef7e75b 100644
--- a/drivers/net/dsa/ocelot/felix.c
+++ b/drivers/net/dsa/ocelot/felix.c
@@ -176,8 +176,7 @@ static void felix_phylink_validate(struct dsa_switch *ds, int port,
 	phylink_set(mask, 100baseT_Full);
 	phylink_set(mask, 1000baseT_Full);
 
-	/* The internal ports that run at 2.5G are overclocked GMII */
-	if (state->interface == PHY_INTERFACE_MODE_GMII ||
+	if (state->interface == PHY_INTERFACE_MODE_INTERNAL ||
 	    state->interface == PHY_INTERFACE_MODE_2500BASEX ||
 	    state->interface == PHY_INTERFACE_MODE_USXGMII) {
 		phylink_set(mask, 2500baseT_Full);
diff --git a/drivers/net/dsa/ocelot/felix_vsc9959.c b/drivers/net/dsa/ocelot/felix_vsc9959.c
index 2c812b481778..93800e81cdd4 100644
--- a/drivers/net/dsa/ocelot/felix_vsc9959.c
+++ b/drivers/net/dsa/ocelot/felix_vsc9959.c
@@ -955,8 +955,7 @@ static int vsc9959_prevalidate_phy_mode(struct ocelot *ocelot, int port,
 					phy_interface_t phy_mode)
 {
 	switch (phy_mode) {
-	case PHY_INTERFACE_MODE_GMII:
-		/* Only supported on internal to-CPU ports */
+	case PHY_INTERFACE_MODE_INTERNAL:
 		if (port != 4 && port != 5)
 			return -ENOTSUPP;
 		return 0;
-- 
2.17.1