| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <E1jEDa8-0008Iv-AR@rmk-PC.armlinux.org.uk>
Date: Tue, 17 Mar 2020 14:52:36 +0000
From: Russell King <rmk+kernel@...linux.org.uk>
To: Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Heiner Kallweit <hkallweit1@...il.com>
Cc: "David S. Miller" <davem@...emloft.net>, netdev@...r.kernel.org
Subject: [PATCH v2 net-next 3/4] net: phylink: pcs: add 802.3 clause 22
helpers
Implement helpers for PCS accessed via the MII bus using 802.3 clause
22 cycles, conforming to 802.3 clause 37 and Cisco SGMII specifications
for the advertisement word.
Signed-off-by: Russell King <rmk+kernel@...linux.org.uk>
---
drivers/net/phy/phylink.c | 206 ++++++++++++++++++++++++++++++++++++++
include/linux/phylink.h | 6 ++
include/uapi/linux/mii.h | 5 +
3 files changed, 217 insertions(+)
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 60f32b354013..ced99e8fda31 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -2068,4 +2068,210 @@ void phylink_helper_basex_speed(struct phylink_link_state *state)
}
EXPORT_SYMBOL_GPL(phylink_helper_basex_speed);
+static void phylink_decode_c37_word(struct phylink_link_state *state,
+ uint16_t config_reg, int speed)
+{
+ bool tx_pause, rx_pause;
+ int fd_bit;
+
+ if (speed == SPEED_2500)
+ fd_bit = ETHTOOL_LINK_MODE_2500baseX_Full_BIT;
+ else
+ fd_bit = ETHTOOL_LINK_MODE_1000baseX_Full_BIT;
+
+ mii_lpa_mod_linkmode_x(state->lp_advertising, config_reg, fd_bit);
+
+ if (linkmode_test_bit(fd_bit, state->advertising) &&
+ linkmode_test_bit(fd_bit, state->lp_advertising)) {
+ state->speed = speed;
+ state->duplex = DUPLEX_FULL;
+ } else {
+ /* negotiation failure */
+ state->link = false;
+ }
+
+ linkmode_resolve_pause(state->advertising, state->lp_advertising,
+ &tx_pause, &rx_pause);
+
+ if (tx_pause)
+ state->pause |= MLO_PAUSE_TX;
+ if (rx_pause)
+ state->pause |= MLO_PAUSE_RX;
+}
+
+static void phylink_decode_sgmii_word(struct phylink_link_state *state,
+ uint16_t config_reg)
+{
+ if (!(config_reg & LPA_SGMII_LINK)) {
+ state->link = false;
+ return;
+ }
+
+ switch (config_reg & LPA_SGMII_SPD_MASK) {
+ case LPA_SGMII_10:
+ state->speed = SPEED_10;
+ break;
+ case LPA_SGMII_100:
+ state->speed = SPEED_100;
+ break;
+ case LPA_SGMII_1000:
+ state->speed = SPEED_1000;
+ break;
+ default:
+ state->link = false;
+ return;
+ }
+ if (config_reg & LPA_SGMII_FULL_DUPLEX)
+ state->duplex = DUPLEX_FULL;
+ else
+ state->duplex = DUPLEX_HALF;
+}
+
+/**
+ * phylink_mii_c22_pcs_get_state() - read the MAC PCS state
+ * @pcs: a pointer to a &struct mdio_device.
+ * @state: a pointer to a &struct phylink_link_state.
+ *
+ * Helper for MAC PCS supporting the 802.3 clause 22 register set for
+ * clause 37 negotiation and/or SGMII control.
+ *
+ * Read the MAC PCS state from the MII device configured in @config and
+ * parse the Clause 37 or Cisco SGMII link partner negotiation word into
+ * the phylink @state structure. This is suitable to be directly plugged
+ * into the mac_pcs_get_state() member of the struct phylink_mac_ops
+ * structure.
+ */
+void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
+ struct phylink_link_state *state)
+{
+ struct mii_bus *bus = pcs->bus;
+ int addr = pcs->addr;
+ int bmsr, lpa;
+
+ bmsr = mdiobus_read(bus, addr, MII_BMSR);
+ lpa = mdiobus_read(bus, addr, MII_LPA);
+ if (bmsr < 0 || lpa < 0) {
+ state->link = false;
+ return;
+ }
+
+ state->link = !!(bmsr & BMSR_LSTATUS);
+ state->an_complete = !!(bmsr & BMSR_ANEGCOMPLETE);
+ if (!state->link)
+ return;
+
+ switch (state->interface) {
+ case PHY_INTERFACE_MODE_1000BASEX:
+ phylink_decode_c37_word(state, lpa, SPEED_1000);
+ break;
+
+ case PHY_INTERFACE_MODE_2500BASEX:
+ phylink_decode_c37_word(state, lpa, SPEED_2500);
+ break;
+
+ case PHY_INTERFACE_MODE_SGMII:
+ phylink_decode_sgmii_word(state, lpa);
+ break;
+
+ default:
+ state->link = false;
+ break;
+ }
+}
+EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_get_state);
+
+/**
+ * phylink_mii_c22_pcs_set_advertisement() - configure the clause 37 PCS
+ * advertisement
+ * @pcs: a pointer to a &struct mdio_device.
+ * @state: a pointer to the state being configured.
+ *
+ * Helper for MAC PCS supporting the 802.3 clause 22 register set for
+ * clause 37 negotiation and/or SGMII control.
+ *
+ * Configure the clause 37 PCS advertisement as specified by @state. This
+ * does not trigger a renegotiation; phylink will do that via the
+ * mac_an_restart() method of the struct phylink_mac_ops structure.
+ *
+ * Returns negative error code on failure to configure the advertisement,
+ * zero if no change has been made, or one if the advertisement has changed.
+ */
+int phylink_mii_c22_pcs_set_advertisement(struct mdio_device *pcs,
+ const struct phylink_link_state *state)
+{
+ struct mii_bus *bus = pcs->bus;
+ int addr = pcs->addr;
+ int val, ret;
+ u16 adv;
+
+ switch (state->interface) {
+ case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
+ adv = ADVERTISE_1000XFULL;
+ if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+ state->advertising))
+ adv |= ADVERTISE_1000XPAUSE;
+ if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+ state->advertising))
+ adv |= ADVERTISE_1000XPSE_ASYM;
+
+ val = mdiobus_read(bus, addr, MII_ADVERTISE);
+ if (val < 0)
+ return val;
+
+ if (val == adv)
+ return 0;
+
+ ret = mdiobus_write(bus, addr, MII_ADVERTISE, adv);
+ if (ret < 0)
+ return ret;
+
+ return 1;
+
+ case PHY_INTERFACE_MODE_SGMII:
+ val = mdiobus_read(bus, addr, MII_ADVERTISE);
+ if (val < 0)
+ return val;
+
+ if (val == 0x0001)
+ return 0;
+
+ ret = mdiobus_write(bus, addr, MII_ADVERTISE, 0x0001);
+ if (ret < 0)
+ return ret;
+
+ return 1;
+
+ default:
+ /* Nothing to do for other modes */
+ return 0;
+ }
+}
+EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_set_advertisement);
+
+/**
+ * phylink_mii_c22_pcs_an_restart() - restart 802.3z autonegotiation
+ * @pcs: a pointer to a &struct mdio_device.
+ *
+ * Helper for MAC PCS supporting the 802.3 clause 22 register set for
+ * clause 37 negotiation.
+ *
+ * Restart the clause 37 negotiation with the link partner. This is
+ * suitable to be directly plugged into the mac_pcs_get_state() member
+ * of the struct phylink_mac_ops structure.
+ */
+void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs)
+{
+ struct mii_bus *bus = pcs->bus;
+ int val, addr = pcs->addr;
+
+ val = mdiobus_read(bus, addr, MII_BMCR);
+ if (val >= 0) {
+ val |= BMCR_ANRESTART;
+
+ mdiobus_write(bus, addr, MII_BMCR, val);
+ }
+}
+EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_an_restart);
+
MODULE_LICENSE("GPL v2");
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 2180eb1aa254..de591c2fb37e 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -317,4 +317,10 @@ int phylink_mii_ioctl(struct phylink *, struct ifreq *, int);
void phylink_set_port_modes(unsigned long *bits);
void phylink_helper_basex_speed(struct phylink_link_state *state);
+void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
+ struct phylink_link_state *state);
+int phylink_mii_c22_pcs_set_advertisement(struct mdio_device *pcs,
+ const struct phylink_link_state *state);
+void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs);
+
#endif
diff --git a/include/uapi/linux/mii.h b/include/uapi/linux/mii.h
index 0b9c3beda345..90f9b4e1ba27 100644
--- a/include/uapi/linux/mii.h
+++ b/include/uapi/linux/mii.h
@@ -134,11 +134,16 @@
/* MAC and PHY tx_config_Reg[15:0] for SGMII in-band auto-negotiation.*/
#define ADVERTISE_SGMII 0x0001 /* MAC can do SGMII */
#define LPA_SGMII 0x0001 /* PHY can do SGMII */
+#define LPA_SGMII_SPD_MASK 0x0c00 /* SGMII speed mask */
+#define LPA_SGMII_FULL_DUPLEX 0x1000 /* SGMII full duplex */
#define LPA_SGMII_DPX_SPD_MASK 0x1C00 /* SGMII duplex and speed bits */
+#define LPA_SGMII_10 0x0000 /* 10Mbps */
#define LPA_SGMII_10HALF 0x0000 /* Can do 10mbps half-duplex */
#define LPA_SGMII_10FULL 0x1000 /* Can do 10mbps full-duplex */
+#define LPA_SGMII_100 0x0400 /* 100Mbps */
#define LPA_SGMII_100HALF 0x0400 /* Can do 100mbps half-duplex */
#define LPA_SGMII_100FULL 0x1400 /* Can do 100mbps full-duplex */
+#define LPA_SGMII_1000 0x0800 /* 1000Mbps */
#define LPA_SGMII_1000HALF 0x0800 /* Can do 1000mbps half-duplex */
#define LPA_SGMII_1000FULL 0x1800 /* Can do 1000mbps full-duplex */
#define LPA_SGMII_LINK 0x8000 /* PHY link with copper-side partner */
--
2.20.1
Powered by blists - more mailing lists