netdev - RE: [RFC,net-next,v1, 1/1] net: stmmac: Enable SERDES power up/down sequence

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <BYAPR11MB27575EF05D65A8AA9AF4128488F00@BYAPR11MB2757.namprd11.prod.outlook.com>
Date:   Mon, 23 Mar 2020 08:16:29 +0000
From:   "Voon, Weifeng" <weifeng.voon@...el.com>
To:     Jose Abreu <Jose.Abreu@...opsys.com>,
        "David S . Miller" <davem@...emloft.net>,
        Maxime Coquelin <mcoquelin.stm32@...il.com>
CC:     "netdev@...r.kernel.org" <netdev@...r.kernel.org>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        "Giuseppe Cavallaro" <peppe.cavallaro@...com>,
        Andrew Lunn <andrew@...n.ch>,
        "Alexandre Torgue" <alexandre.torgue@...com>,
        "Ong, Boon Leong" <boon.leong.ong@...el.com>
Subject: RE: [RFC,net-next,v1, 1/1] net: stmmac: Enable SERDES power up/down
 sequence

> > This patch is to enable Intel SERDES power up/down sequence. The
> > SERDES converts 8/10 bits data to SGMII signal. Below is an example of
> > HW configuration for SGMII mode. The SERDES is located in the PHY IF
> > in the diagram below.
> >
> > <-----------------GBE Controller---------->|<--External PHY chip-->
> > +----------+         +----+            +---+           +----------+
> > |   EQoS   | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
> > |   MAC    |         |xPCS|            |IF |           | PHY      |
> > +----------+         +----+            +---+           +----------+
> >        ^               ^                 ^                ^
> >        |               |                 |                |
> >        +---------------------MDIO-------------------------+
> >
> > PHY IF configuration and status registers are accessible through mdio
> > address 0x15 which is defined as intel_adhoc_addr. During D0, The
> > driver will need to power up PHY IF by changing the power state to P0.
> > Likewise, for D3, the driver sets PHY IF power state to P3.
> 
> I don't think this is the right approach.
> 
> You could just add a new "mdio-intel-serdes" to phy/ folder just like I
> did with XPCS because this is mostly related with PHY settings rather
> than EQoS.
I am taking this approach to put it in stmmac folder rather than phy folder
as a generic mdio-intel-serdes as this is a specific Intel serdes architecture which
would only pair with DW EQos and DW xPCS HW. Since this serdes will not able to
pair other MAC or other non-Intel platform, I would like you to reconsider this
approach. I am open for discussion. 
Thanks Jose for the fast response.

Regards,
Weifeng  

> 
> Perhaps Andrew has better insight on this.
> 
> BTW, are you using the standard XPCS helpers in phy/ folder ? Is it
> working fine for you ?
> 
> ---
> Thanks,
> Jose Miguel Abreu