| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <ac3758c0b78956936c6011d7517a4bdfde3a352e.1588344146.git.mchehab+huawei@kernel.org>
Date: Fri, 1 May 2020 16:44:38 +0200
From: Mauro Carvalho Chehab <mchehab+huawei@...nel.org>
To: Linux Doc Mailing List <linux-doc@...r.kernel.org>
Cc: Mauro Carvalho Chehab <mchehab+huawei@...nel.org>,
linux-kernel@...r.kernel.org, Jonathan Corbet <corbet@....net>,
"David S. Miller" <davem@...emloft.net>,
Jakub Kicinski <kuba@...nel.org>, netdev@...r.kernel.org
Subject: [PATCH 16/37] docs: networking: device drivers: convert chelsio/cxgb.txt to ReST
- add SPDX header;
- use copyright symbol;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- add notes markups;
- mark tables as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@...nel.org>
---
.../chelsio/{cxgb.txt => cxgb.rst} | 183 +++++++++++-------
.../networking/device_drivers/index.rst | 1 +
drivers/net/ethernet/chelsio/Kconfig | 2 +-
3 files changed, 114 insertions(+), 72 deletions(-)
rename Documentation/networking/device_drivers/chelsio/{cxgb.txt => cxgb.rst} (81%)
diff --git a/Documentation/networking/device_drivers/chelsio/cxgb.txt b/Documentation/networking/device_drivers/chelsio/cxgb.rst
similarity index 81%
rename from Documentation/networking/device_drivers/chelsio/cxgb.txt
rename to Documentation/networking/device_drivers/chelsio/cxgb.rst
index 20a887615c4a..435dce5fa2c7 100644
--- a/Documentation/networking/device_drivers/chelsio/cxgb.txt
+++ b/Documentation/networking/device_drivers/chelsio/cxgb.rst
@@ -1,13 +1,18 @@
- Chelsio N210 10Gb Ethernet Network Controller
+.. SPDX-License-Identifier: GPL-2.0
+.. include:: <isonum.txt>
- Driver Release Notes for Linux
+=============================================
+Chelsio N210 10Gb Ethernet Network Controller
+=============================================
- Version 2.1.1
+Driver Release Notes for Linux
- June 20, 2005
+Version 2.1.1
+
+June 20, 2005
+
+.. Contents
-CONTENTS
-========
INTRODUCTION
FEATURES
PERFORMANCE
@@ -16,7 +21,7 @@ CONTENTS
SUPPORT
-INTRODUCTION
+Introduction
============
This document describes the Linux driver for Chelsio 10Gb Ethernet Network
@@ -24,11 +29,11 @@ INTRODUCTION
compatible with the Chelsio N110 model 10Gb NICs.
-FEATURES
+Features
========
- Adaptive Interrupts (adaptive-rx)
- ---------------------------------
+Adaptive Interrupts (adaptive-rx)
+---------------------------------
This feature provides an adaptive algorithm that adjusts the interrupt
coalescing parameters, allowing the driver to dynamically adapt the latency
@@ -39,24 +44,24 @@ FEATURES
ethtool manpage for additional usage information.
By default, adaptive-rx is disabled.
- To enable adaptive-rx:
+ To enable adaptive-rx::
ethtool -C <interface> adaptive-rx on
- To disable adaptive-rx, use ethtool:
+ To disable adaptive-rx, use ethtool::
ethtool -C <interface> adaptive-rx off
After disabling adaptive-rx, the timer latency value will be set to 50us.
- You may set the timer latency after disabling adaptive-rx:
+ You may set the timer latency after disabling adaptive-rx::
ethtool -C <interface> rx-usecs <microseconds>
- An example to set the timer latency value to 100us on eth0:
+ An example to set the timer latency value to 100us on eth0::
ethtool -C eth0 rx-usecs 100
- You may also provide a timer latency value while disabling adaptive-rx:
+ You may also provide a timer latency value while disabling adaptive-rx::
ethtool -C <interface> adaptive-rx off rx-usecs <microseconds>
@@ -64,13 +69,13 @@ FEATURES
will be set to the specified value until changed by the user or until
adaptive-rx is enabled.
- To view the status of the adaptive-rx and timer latency values:
+ To view the status of the adaptive-rx and timer latency values::
ethtool -c <interface>
- TCP Segmentation Offloading (TSO) Support
- -----------------------------------------
+TCP Segmentation Offloading (TSO) Support
+-----------------------------------------
This feature, also known as "large send", enables a system's protocol stack
to offload portions of outbound TCP processing to a network interface card
@@ -80,20 +85,20 @@ FEATURES
Please see the ethtool manpage for additional usage information.
By default, TSO is enabled.
- To disable TSO:
+ To disable TSO::
ethtool -K <interface> tso off
- To enable TSO:
+ To enable TSO::
ethtool -K <interface> tso on
- To view the status of TSO:
+ To view the status of TSO::
ethtool -k <interface>
-PERFORMANCE
+Performance
===========
The following information is provided as an example of how to change system
@@ -111,59 +116,81 @@ PERFORMANCE
your system. You may want to write a script that runs at boot-up which
includes the optimal settings for your system.
- Setting PCI Latency Timer:
- setpci -d 1425:* 0x0c.l=0x0000F800
+ Setting PCI Latency Timer::
+
+ setpci -d 1425::
+
+* 0x0c.l=0x0000F800
+
+ Disabling TCP timestamp::
- Disabling TCP timestamp:
sysctl -w net.ipv4.tcp_timestamps=0
- Disabling SACK:
+ Disabling SACK::
+
sysctl -w net.ipv4.tcp_sack=0
- Setting large number of incoming connection requests:
+ Setting large number of incoming connection requests::
+
sysctl -w net.ipv4.tcp_max_syn_backlog=3000
- Setting maximum receive socket buffer size:
+ Setting maximum receive socket buffer size::
+
sysctl -w net.core.rmem_max=1024000
- Setting maximum send socket buffer size:
+ Setting maximum send socket buffer size::
+
sysctl -w net.core.wmem_max=1024000
- Set smp_affinity (on a multiprocessor system) to a single CPU:
+ Set smp_affinity (on a multiprocessor system) to a single CPU::
+
echo 1 > /proc/irq/<interrupt_number>/smp_affinity
- Setting default receive socket buffer size:
+ Setting default receive socket buffer size::
+
sysctl -w net.core.rmem_default=524287
- Setting default send socket buffer size:
+ Setting default send socket buffer size::
+
sysctl -w net.core.wmem_default=524287
- Setting maximum option memory buffers:
+ Setting maximum option memory buffers::
+
sysctl -w net.core.optmem_max=524287
- Setting maximum backlog (# of unprocessed packets before kernel drops):
+ Setting maximum backlog (# of unprocessed packets before kernel drops)::
+
sysctl -w net.core.netdev_max_backlog=300000
- Setting TCP read buffers (min/default/max):
+ Setting TCP read buffers (min/default/max)::
+
sysctl -w net.ipv4.tcp_rmem="10000000 10000000 10000000"
- Setting TCP write buffers (min/pressure/max):
+ Setting TCP write buffers (min/pressure/max)::
+
sysctl -w net.ipv4.tcp_wmem="10000000 10000000 10000000"
- Setting TCP buffer space (min/pressure/max):
+ Setting TCP buffer space (min/pressure/max)::
+
sysctl -w net.ipv4.tcp_mem="10000000 10000000 10000000"
TCP window size for single connections:
+
The receive buffer (RX_WINDOW) size must be at least as large as the
Bandwidth-Delay Product of the communication link between the sender and
receiver. Due to the variations of RTT, you may want to increase the buffer
size up to 2 times the Bandwidth-Delay Product. Reference page 289 of
"TCP/IP Illustrated, Volume 1, The Protocols" by W. Richard Stevens.
- At 10Gb speeds, use the following formula:
+
+ At 10Gb speeds, use the following formula::
+
RX_WINDOW >= 1.25MBytes * RTT(in milliseconds)
Example for RTT with 100us: RX_WINDOW = (1,250,000 * 0.1) = 125,000
+
RX_WINDOW sizes of 256KB - 512KB should be sufficient.
- Setting the min, max, and default receive buffer (RX_WINDOW) size:
+
+ Setting the min, max, and default receive buffer (RX_WINDOW) size::
+
sysctl -w net.ipv4.tcp_rmem="<min> <default> <max>"
TCP window size for multiple connections:
@@ -174,30 +201,35 @@ PERFORMANCE
not supported on the machine. Experimentation may be necessary to attain
the correct value. This method is provided as a starting point for the
correct receive buffer size.
+
Setting the min, max, and default receive buffer (RX_WINDOW) size is
performed in the same manner as single connection.
-DRIVER MESSAGES
+Driver Messages
===============
The following messages are the most common messages logged by syslog. These
may be found in /var/log/messages.
- Driver up:
+ Driver up::
+
Chelsio Network Driver - version 2.1.1
- NIC detected:
+ NIC detected::
+
eth#: Chelsio N210 1x10GBaseX NIC (rev #), PCIX 133MHz/64-bit
- Link up:
+ Link up::
+
eth#: link is up at 10 Gbps, full duplex
- Link down:
+ Link down::
+
eth#: link is down
-KNOWN ISSUES
+Known Issues
============
These issues have been identified during testing. The following information
@@ -214,27 +246,33 @@ KNOWN ISSUES
To eliminate the TCP retransmits, set smp_affinity on the particular
interrupt to a single CPU. You can locate the interrupt (IRQ) used on
- the N110/N210 by using ifconfig:
- ifconfig <dev_name> | grep Interrupt
- Set the smp_affinity to a single CPU:
- echo 1 > /proc/irq/<interrupt_number>/smp_affinity
+ the N110/N210 by using ifconfig::
+
+ ifconfig <dev_name> | grep Interrupt
+
+ Set the smp_affinity to a single CPU::
+
+ echo 1 > /proc/irq/<interrupt_number>/smp_affinity
It is highly suggested that you do not run the irqbalance daemon on your
system, as this will change any smp_affinity setting you have applied.
The irqbalance daemon runs on a 10 second interval and binds interrupts
- to the least loaded CPU determined by the daemon. To disable this daemon:
- chkconfig --level 2345 irqbalance off
+ to the least loaded CPU determined by the daemon. To disable this daemon::
+
+ chkconfig --level 2345 irqbalance off
By default, some Linux distributions enable the kernel feature,
irqbalance, which performs the same function as the daemon. To disable
- this feature, add the following line to your bootloader:
- noirqbalance
+ this feature, add the following line to your bootloader::
- Example using the Grub bootloader:
- title Red Hat Enterprise Linux AS (2.4.21-27.ELsmp)
- root (hd0,0)
- kernel /vmlinuz-2.4.21-27.ELsmp ro root=/dev/hda3 noirqbalance
- initrd /initrd-2.4.21-27.ELsmp.img
+ noirqbalance
+
+ Example using the Grub bootloader::
+
+ title Red Hat Enterprise Linux AS (2.4.21-27.ELsmp)
+ root (hd0,0)
+ kernel /vmlinuz-2.4.21-27.ELsmp ro root=/dev/hda3 noirqbalance
+ initrd /initrd-2.4.21-27.ELsmp.img
2. After running insmod, the driver is loaded and the incorrect network
interface is brought up without running ifup.
@@ -277,12 +315,13 @@ KNOWN ISSUES
AMD's provides three workarounds for this problem, however, Chelsio
recommends the first option for best performance with this bug:
- For 133Mhz secondary bus operation, limit the transaction length and
- the number of outstanding transactions, via BIOS configuration
- programming of the PCI-X card, to the following:
+ For 133Mhz secondary bus operation, limit the transaction length and
+ the number of outstanding transactions, via BIOS configuration
+ programming of the PCI-X card, to the following:
- Data Length (bytes): 1k
- Total allowed outstanding transactions: 2
+ Data Length (bytes): 1k
+
+ Total allowed outstanding transactions: 2
Please refer to AMD 8131-HT/PCI-X Errata 26310 Rev 3.08 August 2004,
section 56, "133-MHz Mode Split Completion Data Corruption" for more
@@ -293,8 +332,10 @@ KNOWN ISSUES
have issues with these settings, please revert to the "safe" settings
and duplicate the problem before submitting a bug or asking for support.
- NOTE: The default setting on most systems is 8 outstanding transactions
- and 2k bytes data length.
+ .. note::
+
+ The default setting on most systems is 8 outstanding transactions
+ and 2k bytes data length.
4. On multiprocessor systems, it has been noted that an application which
is handling 10Gb networking can switch between CPUs causing degraded
@@ -320,14 +361,16 @@ KNOWN ISSUES
particular CPU: runon 0 ifup eth0
-SUPPORT
+Support
=======
If you have problems with the software or hardware, please contact our
customer support team via email at support@...lsio.com or check our website
at http://www.chelsio.com
-===============================================================================
+-------------------------------------------------------------------------------
+
+::
Chelsio Communications
370 San Aleso Ave.
@@ -343,10 +386,8 @@ You should have received a copy of the GNU General Public License along
with this program; if not, write to the Free Software Foundation, Inc.,
59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
-THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED
+THIS SOFTWARE IS PROVIDED ``AS IS`` AND WITHOUT ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- Copyright (c) 2003-2005 Chelsio Communications. All rights reserved.
-
-===============================================================================
+Copyright |copy| 2003-2005 Chelsio Communications. All rights reserved.
diff --git a/Documentation/networking/device_drivers/index.rst b/Documentation/networking/device_drivers/index.rst
index 7dde314fc957..23c4ec9c9125 100644
--- a/Documentation/networking/device_drivers/index.rst
+++ b/Documentation/networking/device_drivers/index.rst
@@ -31,6 +31,7 @@ Contents:
3com/vortex
amazon/ena
aquantia/atlantic
+ chelsio/cxgb
.. only:: subproject and html
diff --git a/drivers/net/ethernet/chelsio/Kconfig b/drivers/net/ethernet/chelsio/Kconfig
index 9909bfda167e..82cdfa51ce37 100644
--- a/drivers/net/ethernet/chelsio/Kconfig
+++ b/drivers/net/ethernet/chelsio/Kconfig
@@ -26,7 +26,7 @@ config CHELSIO_T1
This driver supports Chelsio gigabit and 10-gigabit
Ethernet cards. More information about adapter features and
performance tuning is in
- <file:Documentation/networking/device_drivers/chelsio/cxgb.txt>.
+ <file:Documentation/networking/device_drivers/chelsio/cxgb.rst>.
For general information about Chelsio and our products, visit
our website at <http://www.chelsio.com>.
--
2.25.4
Powered by blists - more mailing lists