Message-ID: <20200601063918.GD2282@nanopsycho>
Date:   Mon, 1 Jun 2020 08:39:18 +0200
From:   Jiri Pirko <jiri@...nulli.us>
To:     Michael Chan <michael.chan@...adcom.com>
Cc:     Jakub Kicinski <kuba@...nel.org>,
        Vasundhara Volam <vasundhara-v.volam@...adcom.com>,
        David Miller <davem@...emloft.net>,
        Netdev <netdev@...r.kernel.org>, Jiri Pirko <jiri@...lanox.com>
Subject: Re: [PATCH v2 net-next 1/4] devlink: Add new "allow_fw_live_reset"
 generic device parameter.

Wed, May 27, 2020 at 10:57:11PM CEST, michael.chan@...adcom.com wrote:
>On Wed, May 27, 2020 at 1:14 PM Jakub Kicinski <kuba@...nel.org> wrote:
>>
>> On Wed, 27 May 2020 09:07:09 +0530 Vasundhara Volam wrote:
>> > Here is a sample sequence of commands to do a "live reset" to get some
>> > clear idea.
>> > Note that I am providing the examples based on the current patchset.
>> >
>> > 1. FW live reset is disabled in the device/adapter. Here adapter has 2
>> > physical ports.
>> >
>> > $ devlink dev
>> > pci/0000:3b:00.0
>> > pci/0000:3b:00.1
>> > pci/0000:af:00.0
>> > $ devlink dev param show pci/0000:3b:00.0 name allow_fw_live_reset
>> > pci/0000:3b:00.0:
>> >   name allow_fw_live_reset type generic
>> >     values:
>> >       cmode runtime value false
>> >       cmode permanent value false
>> > $ devlink dev param show pci/0000:3b:00.1 name allow_fw_live_reset
>> > pci/0000:3b:00.1:
>> >   name allow_fw_live_reset type generic
>> >     values:
>> >       cmode runtime value false
>> >       cmode permanent value false
>>
>> What's the permanent value? What if after reboot the driver is too old
>> to change this, is the reset still allowed?
>
>The permanent value should be the NVRAM value.  If the NVRAM value is
>false, the feature is always and unconditionally disabled.  If the
>permanent value is true, the feature will only be available when all
>loaded drivers indicate support for it and set the runtime value to
>true.  If an old driver is loaded afterwards, it wouldn't indicate
>support for this feature and it wouldn't set the runtime value to
>true.  So the feature will not be available until the old driver is
>unloaded or upgraded.
>
>>
>> > 2. If a user issues "ethtool --reset p1p1 all", the device cannot
>> > perform "live reset" as capability is not enabled.
>> >
>> > User needs to do a driver reload, for firmware to undergo reset.
>>
>> Why does driver reload have anything to do with resetting a potentially
>> MH device?
>
>I think she meant that all drivers have to be unloaded before the
>reset would take place in case it's a MH device since live reset is
>not supported.  If it's a single function device, unloading this
>driver is sufficient.
>
>>
>> > $ ethtool --reset p1p1 all
>>
>> Reset probably needs to be done via devlink. In any case you need a new
>> reset level for resetting MH devices and smartnics, because the current
>> reset mask covers port local, and host local cases, not any form of MH.
>
>RIght.  This reset could be just a single function reset in this example.
>
>>
>> > ETHTOOL_RESET 0xffffffff
>> > Components reset:     0xff0000
>> > Components not reset: 0xff00ffff
>> > $ dmesg
>> > [  198.745822] bnxt_en 0000:3b:00.0 p1p1: Firmware reset request successful.
>> > [  198.745836] bnxt_en 0000:3b:00.0 p1p1: Reload driver to complete reset
>>
>> You said the reset was not performed, yet there is no information to
>> that effect in the log?!
>
>The firmware has been requested to reset, but the reset hasn't taken
>place yet because live reset cannot be done.  We can make the logs
>more clear.
>
>>
>> > 3. Now enable the capability in the device and reboot for device to
>> > enable the capability. Firmware does not get reset just by setting the
>> > param to true.
>> >
>> > $ devlink dev param set pci/0000:3b:00.1 name allow_fw_live_reset
>> > value true cmode permanent
>> >
>> > 4. After reboot, values of param.
>>
>> Is the reboot required here?
>>
>
>In general, our new NVRAM permanent parameters will take effect after
>reset (or reboot).

Ah, you need a reboot. I was not expecting that :/ So the "devlink dev
reload" attr would not work for you. MLNX hardware can change this on
runtime.


>
>> > $ devlink dev param show pci/0000:3b:00.1 name allow_fw_live_reset
>> > pci/0000:3b:00.1:
>> >   name allow_fw_live_reset type generic
>> >     values:
>> >       cmode runtime value true
>>
>> Why is runtime value true now?
>>
>
>If the permanent (NVRAM) parameter is true, all loaded new drivers
>will indicate support for this feature and set the runtime value to
>true by default.  The runtime value would not be true if any loaded
>driver is too old or has set the runtime value to false.

This is a bit odd. It is a configuration, not an indication. When you
want to indicate what you support something, I think it should be done
in a different place. I think that "devlink dev info" is the place to
put it, I think that we need "capabilities" there.

Powered by blists - more mailing lists