| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200617213326.1532365-4-heiko@sntech.de>
Date: Wed, 17 Jun 2020 23:33:26 +0200
From: Heiko Stuebner <heiko@...ech.de>
To: davem@...emloft.net, kuba@...nel.org
Cc: robh+dt@...nel.org, andrew@...n.ch, f.fainelli@...il.com,
hkallweit1@...il.com, linux@...linux.org.uk,
netdev@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, heiko@...ech.de,
christoph.muellner@...obroma-systems.com,
Heiko Stuebner <heiko.stuebner@...obroma-systems.com>
Subject: [PATCH v4 3/3] net: phy: mscc: handle the clkout control on some phy variants
From: Heiko Stuebner <heiko.stuebner@...obroma-systems.com>
At least VSC8530/8531/8540/8541 contain a clock output that can emit
a predefined rate of 25, 50 or 125MHz.
This may then feed back into the network interface as source clock.
So follow the example the at803x already set and introduce a
vsc8531,clk-out-frequency property to set that output.
Signed-off-by: Heiko Stuebner <heiko.stuebner@...obroma-systems.com>
---
drivers/net/phy/mscc/mscc.h | 9 ++++
drivers/net/phy/mscc/mscc_main.c | 87 +++++++++++++++++++++++++++++---
2 files changed, 89 insertions(+), 7 deletions(-)
diff --git a/drivers/net/phy/mscc/mscc.h b/drivers/net/phy/mscc/mscc.h
index fbcee5fce7b2..a3afc35c3eab 100644
--- a/drivers/net/phy/mscc/mscc.h
+++ b/drivers/net/phy/mscc/mscc.h
@@ -218,6 +218,13 @@ enum rgmii_clock_delay {
#define INT_MEM_DATA_M 0x00ff
#define INT_MEM_DATA(x) (INT_MEM_DATA_M & (x))
+#define MSCC_CLKOUT_CNTL 13
+#define CLKOUT_ENABLE BIT(15)
+#define CLKOUT_FREQ_MASK GENMASK(14, 13)
+#define CLKOUT_FREQ_25M (0x0 << 13)
+#define CLKOUT_FREQ_50M (0x1 << 13)
+#define CLKOUT_FREQ_125M (0x2 << 13)
+
#define MSCC_PHY_PROC_CMD 18
#define PROC_CMD_NCOMPLETED 0x8000
#define PROC_CMD_FAILED 0x4000
@@ -360,6 +367,8 @@ struct vsc8531_private {
*/
unsigned int base_addr;
+ u32 clkout_rate;
+
#if IS_ENABLED(CONFIG_MACSEC)
/* MACsec fields:
* - One SecY per device (enforced at the s/w implementation level)
diff --git a/drivers/net/phy/mscc/mscc_main.c b/drivers/net/phy/mscc/mscc_main.c
index 5d2777522fb4..2f06cfa2f539 100644
--- a/drivers/net/phy/mscc/mscc_main.c
+++ b/drivers/net/phy/mscc/mscc_main.c
@@ -432,6 +432,18 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev,
return led_mode;
}
+static void vsc8531_dt_clkout_rate_get(struct phy_device *phydev)
+{
+ struct vsc8531_private *priv = phydev->priv;
+ struct device *dev = &phydev->mdio.dev;
+ struct device_node *of_node = dev->of_node;
+
+ if (!of_node)
+ return;
+
+ of_property_read_u32(of_node, "enet-phy-clock-out-frequency",
+ &priv->clkout_rate);
+}
#else
static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)
{
@@ -444,6 +456,10 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev,
{
return default_mode;
}
+
+static void vsc8531_dt_clkout_rate_get(struct phy_device *phydev)
+{
+}
#endif /* CONFIG_OF_MDIO */
static int vsc85xx_dt_led_modes_get(struct phy_device *phydev,
@@ -1508,6 +1524,37 @@ static int vsc85xx_config_init(struct phy_device *phydev)
return 0;
}
+static int vsc8531_config_init(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531 = phydev->priv;
+ u16 val;
+ int rc;
+
+ rc = vsc85xx_config_init(phydev);
+ if (rc)
+ return rc;
+
+ switch (vsc8531->clkout_rate) {
+ case 0:
+ val = 0;
+ break;
+ case 25000000:
+ val = CLKOUT_FREQ_25M | CLKOUT_ENABLE;
+ break;
+ case 50000000:
+ val = CLKOUT_FREQ_50M | CLKOUT_ENABLE;
+ break;
+ case 125000000:
+ val = CLKOUT_FREQ_125M | CLKOUT_ENABLE;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return phy_write_paged(phydev, MSCC_PHY_PAGE_EXTENDED_GPIO,
+ MSCC_CLKOUT_CNTL, val);
+}
+
static int vsc8584_did_interrupt(struct phy_device *phydev)
{
int rc = 0;
@@ -1981,6 +2028,32 @@ static int vsc8514_probe(struct phy_device *phydev)
vsc8531->base_addr, 0);
}
+static int vsc8531_probe(struct phy_device *phydev)
+{
+ struct vsc8531_private *vsc8531;
+ int rate_magic, rc;
+ u32 default_mode[2] = {VSC8531_LINK_1000_ACTIVITY,
+ VSC8531_LINK_100_ACTIVITY};
+
+ rate_magic = vsc85xx_edge_rate_magic_get(phydev);
+ if (rate_magic < 0)
+ return rate_magic;
+
+ rc = vsc85xx_probe_helper(phydev, default_mode,
+ ARRAY_SIZE(default_mode),
+ VSC85XX_SUPP_LED_MODES,
+ vsc85xx_hw_stats,
+ ARRAY_SIZE(vsc85xx_hw_stats));
+ if (rc < 0)
+ return rc;
+
+ vsc8531 = phydev->priv;
+ vsc8531->rate_magic = rate_magic;
+ vsc8531_dt_clkout_rate_get(phydev);
+
+ return 0;
+}
+
static int vsc8574_probe(struct phy_device *phydev)
{
struct vsc8531_private *vsc8531;
@@ -2136,14 +2209,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_BASIC_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2160,14 +2233,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2184,14 +2257,14 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_BASIC_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
.config_intr = &vsc85xx_config_intr,
.suspend = &genphy_suspend,
.resume = &genphy_resume,
- .probe = &vsc85xx_probe,
+ .probe = &vsc8531_probe,
.set_wol = &vsc85xx_wol_set,
.get_wol = &vsc85xx_wol_get,
.get_tunable = &vsc85xx_get_tunable,
@@ -2208,7 +2281,7 @@ static struct phy_driver vsc85xx_driver[] = {
.phy_id_mask = 0xfffffff0,
/* PHY_GBIT_FEATURES */
.soft_reset = &genphy_soft_reset,
- .config_init = &vsc85xx_config_init,
+ .config_init = &vsc8531_config_init,
.config_aneg = &vsc85xx_config_aneg,
.read_status = &vsc85xx_read_status,
.ack_interrupt = &vsc85xx_ack_interrupt,
--
2.26.2
Powered by blists - more mailing lists