| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAKgT0UdDjabvShwDv0qiume=Q2RKGkm3JhPMZ+f8v5yO37ZLxA@mail.gmail.com>
Date: Thu, 16 Jul 2020 08:18:25 -0700
From: Alexander Duyck <alexander.duyck@...il.com>
To: Ian Kumlien <ian.kumlien@...il.com>
Cc: Jakub Kicinski <kuba@...nel.org>,
Linux Kernel Network Developers <netdev@...r.kernel.org>,
intel-wired-lan <intel-wired-lan@...ts.osuosl.org>
Subject: Re: [Intel-wired-lan] NAT performance issue 944mbit -> ~40mbit
On Wed, Jul 15, 2020 at 5:00 PM Ian Kumlien <ian.kumlien@...il.com> wrote:
>
> On Thu, Jul 16, 2020 at 1:42 AM Alexander Duyck
> <alexander.duyck@...il.com> wrote:
> > On Wed, Jul 15, 2020 at 3:51 PM Ian Kumlien <ian.kumlien@...il.com> wrote:
> > > On Thu, Jul 16, 2020 at 12:32 AM Alexander Duyck
> > > <alexander.duyck@...il.com> wrote:
> > > > On Wed, Jul 15, 2020 at 3:00 PM Ian Kumlien <ian.kumlien@...il.com> wrote:
> > > > > On Wed, Jul 15, 2020 at 11:40 PM Jakub Kicinski <kuba@...nel.org> wrote:
> > > > > > On Wed, 15 Jul 2020 23:12:23 +0200 Ian Kumlien wrote:
> > > > > > > On Wed, Jul 15, 2020 at 11:02 PM Ian Kumlien <ian.kumlien@...il.com> wrote:
> > > > > > > > On Wed, Jul 15, 2020 at 10:31 PM Jakub Kicinski <kuba@...nel.org> wrote:
> > > > > > > > > On Wed, 15 Jul 2020 22:05:58 +0200 Ian Kumlien wrote:
> > > > > > > > > > After a lot of debugging it turns out that the bug is in igb...
> > > > > > > > > >
> > > > > > > > > > driver: igb
> > > > > > > > > > version: 5.6.0-k
> > > > > > > > > > firmware-version: 0. 6-1
> > > > > > > > > >
> > > > > > > > > > 03:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network
> > > > > > > > > > Connection (rev 03)
> > > > > > > > >
> > > > > > > > > Unclear to me what you're actually reporting. Is this a regression
> > > > > > > > > after a kernel upgrade? Compared to no NAT?
> > > > > > > >
> > > > > > > > It only happens on "internet links"
> > > > > > > >
> > > > > > > > Lets say that A is client with ibg driver, B is a firewall running NAT
> > > > > > > > with ixgbe drivers, C is another local node with igb and
> > > > > > > > D is a remote node with a bridge backed by a bnx2 interface.
> > > > > > > >
> > > > > > > > A -> B -> C is ok (B and C is on the same switch)
> > > > > > > >
> > > > > > > > A -> B -> D -- 32-40mbit
> > > > > > > >
> > > > > > > > B -> D 944 mbit
> > > > > > > > C -> D 944 mbit
> > > > > > > >
> > > > > > > > A' -> D ~933 mbit (A with realtek nic -- also link is not idle atm)
> > > > > > >
> > > > > > > This should of course be A' -> B -> D
> > > > > > >
> > > > > > > Sorry, I've been scratching my head for about a week...
> > > > > >
> > > > > > Hm, only thing that comes to mind if A' works reliably and A doesn't is
> > > > > > that A has somehow broken TCP offloads. Could you try disabling things
> > > > > > via ethtool -K and see if those settings make a difference?
> > > > >
> > > > > It's a bit hard since it works like this, turned tso off:
> > > > > [ ID] Interval Transfer Bitrate Retr Cwnd
> > > > > [ 5] 0.00-1.00 sec 108 MBytes 902 Mbits/sec 0 783 KBytes
> > > > > [ 5] 1.00-2.00 sec 110 MBytes 923 Mbits/sec 31 812 KBytes
> > > > > [ 5] 2.00-3.00 sec 111 MBytes 933 Mbits/sec 92 772 KBytes
> > > > > [ 5] 3.00-4.00 sec 110 MBytes 923 Mbits/sec 0 834 KBytes
> > > > > [ 5] 4.00-5.00 sec 111 MBytes 933 Mbits/sec 60 823 KBytes
> > > > > [ 5] 5.00-6.00 sec 110 MBytes 923 Mbits/sec 31 789 KBytes
> > > > > [ 5] 6.00-7.00 sec 111 MBytes 933 Mbits/sec 0 786 KBytes
> > > > > [ 5] 7.00-8.00 sec 110 MBytes 923 Mbits/sec 0 761 KBytes
> > > > > [ 5] 8.00-9.00 sec 110 MBytes 923 Mbits/sec 0 772 KBytes
> > > > > [ 5] 9.00-10.00 sec 109 MBytes 912 Mbits/sec 0 868 KBytes
> > > > > - - - - - - - - - - - - - - - - - - - - - - - - -
> > > > > [ ID] Interval Transfer Bitrate Retr
> > > > > [ 5] 0.00-10.00 sec 1.07 GBytes 923 Mbits/sec 214 sender
> > > > > [ 5] 0.00-10.00 sec 1.07 GBytes 920 Mbits/sec receiver
> > > > >
> > > > > Continued running tests:
> > > > > [ ID] Interval Transfer Bitrate Retr Cwnd
> > > > > [ 5] 0.00-1.00 sec 5.82 MBytes 48.8 Mbits/sec 0 82.0 KBytes
> > > > > [ 5] 1.00-2.00 sec 4.97 MBytes 41.7 Mbits/sec 0 130 KBytes
> > > > > [ 5] 2.00-3.00 sec 5.28 MBytes 44.3 Mbits/sec 0 99.0 KBytes
> > > > > [ 5] 3.00-4.00 sec 5.28 MBytes 44.3 Mbits/sec 0 105 KBytes
> > > > > [ 5] 4.00-5.00 sec 5.28 MBytes 44.3 Mbits/sec 0 122 KBytes
> > > > > [ 5] 5.00-6.00 sec 5.28 MBytes 44.3 Mbits/sec 0 82.0 KBytes
> > > > > [ 5] 6.00-7.00 sec 5.28 MBytes 44.3 Mbits/sec 0 79.2 KBytes
> > > > > [ 5] 7.00-8.00 sec 5.28 MBytes 44.3 Mbits/sec 0 110 KBytes
> > > > > [ 5] 8.00-9.00 sec 5.28 MBytes 44.3 Mbits/sec 0 156 KBytes
> > > > > [ 5] 9.00-10.00 sec 5.28 MBytes 44.3 Mbits/sec 0 87.7 KBytes
> > > > > - - - - - - - - - - - - - - - - - - - - - - - - -
> > > > > [ ID] Interval Transfer Bitrate Retr
> > > > > [ 5] 0.00-10.00 sec 53.0 MBytes 44.5 Mbits/sec 0 sender
> > > > > [ 5] 0.00-10.00 sec 52.5 MBytes 44.1 Mbits/sec receiver
> > > > >
> > > > > [ ID] Interval Transfer Bitrate Retr Cwnd
> > > > > [ 5] 0.00-1.00 sec 7.08 MBytes 59.4 Mbits/sec 0 156 KBytes
> > > > > [ 5] 1.00-2.00 sec 5.97 MBytes 50.0 Mbits/sec 0 110 KBytes
> > > > > [ 5] 2.00-3.00 sec 4.97 MBytes 41.7 Mbits/sec 0 124 KBytes
> > > > > [ 5] 3.00-4.00 sec 5.47 MBytes 45.9 Mbits/sec 0 96.2 KBytes
> > > > > [ 5] 4.00-5.00 sec 5.47 MBytes 45.9 Mbits/sec 0 158 KBytes
> > > > > [ 5] 5.00-6.00 sec 4.97 MBytes 41.7 Mbits/sec 0 70.7 KBytes
> > > > > [ 5] 6.00-7.00 sec 5.47 MBytes 45.9 Mbits/sec 0 113 KBytes
> > > > > [ 5] 7.00-8.00 sec 5.47 MBytes 45.9 Mbits/sec 0 96.2 KBytes
> > > > > [ 5] 8.00-9.00 sec 4.97 MBytes 41.7 Mbits/sec 0 84.8 KBytes
> > > > > [ 5] 9.00-10.00 sec 5.47 MBytes 45.9 Mbits/sec 0 116 KBytes
> > > > > - - - - - - - - - - - - - - - - - - - - - - - - -
> > > > > [ ID] Interval Transfer Bitrate Retr
> > > > > [ 5] 0.00-10.00 sec 55.3 MBytes 46.4 Mbits/sec 0 sender
> > > > > [ 5] 0.00-10.00 sec 53.9 MBytes 45.2 Mbits/sec receiver
> > > > >
> > > > > And the low bandwidth continues with:
> > > > > ethtool -k enp3s0 |grep ": on"
> > > > > rx-vlan-offload: on
> > > > > tx-vlan-offload: on [requested off]
> > > > > highdma: on [fixed]
> > > > > rx-vlan-filter: on [fixed]
> > > > > tx-gre-segmentation: on
> > > > > tx-gre-csum-segmentation: on
> > > > > tx-ipxip4-segmentation: on
> > > > > tx-ipxip6-segmentation: on
> > > > > tx-udp_tnl-segmentation: on
> > > > > tx-udp_tnl-csum-segmentation: on
> > > > > tx-gso-partial: on
> > > > > tx-udp-segmentation: on
> > > > > hw-tc-offload: on
> > > > >
> > > > > Can't quite find how to turn those off since they aren't listed in
> > > > > ethtool (since the text is not what you use to enable/disable)
> > > >
> > > > To disable them you would just repeat the same string in the display
> > > > string. So it should just be "ethtool -K enp3s0 tx-gso-partial off"
> > > > and that would turn off a large chunk of them as all the encapsulated
> > > > support requires gso partial support.
> > >
> > > ethtool -k enp3s0 |grep ": on"
> > > highdma: on [fixed]
> > > rx-vlan-filter: on [fixed]
> > > ---
> > > And then back to back:
> > > [ ID] Interval Transfer Bitrate Retr Cwnd
> > > [ 5] 0.00-1.00 sec 4.91 MBytes 41.2 Mbits/sec 0 45.2 KBytes
> > > [ 5] 1.00-2.00 sec 4.47 MBytes 37.5 Mbits/sec 0 52.3 KBytes
> > > [ 5] 2.00-3.00 sec 4.47 MBytes 37.5 Mbits/sec 0 42.4 KBytes
> > > [ 5] 3.00-4.00 sec 4.47 MBytes 37.5 Mbits/sec 0 141 KBytes
> > > [ 5] 4.00-5.00 sec 111 MBytes 928 Mbits/sec 63 764 KBytes
> > > [ 5] 5.00-6.00 sec 86.2 MBytes 724 Mbits/sec 0 744 KBytes
> > > [ 5] 6.00-7.00 sec 98.8 MBytes 828 Mbits/sec 61 769 KBytes
> > > [ 5] 7.00-8.00 sec 110 MBytes 923 Mbits/sec 0 749 KBytes
> > > [ 5] 8.00-9.00 sec 110 MBytes 923 Mbits/sec 0 741 KBytes
> > > [ 5] 9.00-10.00 sec 110 MBytes 923 Mbits/sec 31 761 KBytes
> > > - - - - - - - - - - - - - - - - - - - - - - - - -
> > > [ ID] Interval Transfer Bitrate Retr
> > > [ 5] 0.00-10.00 sec 644 MBytes 540 Mbits/sec 155 sender
> > > [ 5] 0.00-10.01 sec 641 MBytes 537 Mbits/sec receiver
> > >
> > > and we're back at the not working bit:
> > > [ ID] Interval Transfer Bitrate Retr Cwnd
> > > [ 5] 0.00-1.00 sec 4.84 MBytes 40.6 Mbits/sec 0 42.4 KBytes
> > > [ 5] 1.00-2.00 sec 4.60 MBytes 38.6 Mbits/sec 0 42.4 KBytes
> > > [ 5] 2.00-3.00 sec 4.23 MBytes 35.4 Mbits/sec 0 42.4 KBytes
> > > [ 5] 3.00-4.00 sec 4.47 MBytes 37.5 Mbits/sec 0 67.9 KBytes
> > > [ 5] 4.00-5.00 sec 4.47 MBytes 37.5 Mbits/sec 0 42.4 KBytes
> > > [ 5] 5.00-6.00 sec 4.23 MBytes 35.4 Mbits/sec 0 42.4 KBytes
> > > [ 5] 6.00-7.00 sec 4.23 MBytes 35.4 Mbits/sec 0 42.4 KBytes
> > > [ 5] 7.00-8.00 sec 4.47 MBytes 37.5 Mbits/sec 0 67.9 KBytes
> > > [ 5] 8.00-9.00 sec 4.47 MBytes 37.5 Mbits/sec 0 53.7 KBytes
> > > [ 5] 9.00-10.00 sec 4.47 MBytes 37.5 Mbits/sec 0 79.2 KBytes
> > > - - - - - - - - - - - - - - - - - - - - - - - - -
> > > [ ID] Interval Transfer Bitrate Retr
> > > [ 5] 0.00-10.00 sec 44.5 MBytes 37.3 Mbits/sec 0 sender
> > > [ 5] 0.00-10.00 sec 43.9 MBytes 36.8 Mbits/sec receiver
> > >
> > > > > I was hoping that you'd have a clue of something that might introduce
> > > > > a regression - ie specific patches to try to revert
> > > > >
> > > > > Btw, the same issue applies to udp as werll
> > > > >
> > > > > [ ID] Interval Transfer Bitrate Total Datagrams
> > > > > [ 5] 0.00-1.00 sec 6.77 MBytes 56.8 Mbits/sec 4900
> > > > > [ 5] 1.00-2.00 sec 4.27 MBytes 35.8 Mbits/sec 3089
> > > > > [ 5] 2.00-3.00 sec 4.20 MBytes 35.2 Mbits/sec 3041
> > > > > [ 5] 3.00-4.00 sec 4.30 MBytes 36.1 Mbits/sec 3116
> > > > > [ 5] 4.00-5.00 sec 4.24 MBytes 35.6 Mbits/sec 3070
> > > > > [ 5] 5.00-6.00 sec 4.21 MBytes 35.3 Mbits/sec 3047
> > > > > [ 5] 6.00-7.00 sec 4.29 MBytes 36.0 Mbits/sec 3110
> > > > > [ 5] 7.00-8.00 sec 4.28 MBytes 35.9 Mbits/sec 3097
> > > > > [ 5] 8.00-9.00 sec 4.25 MBytes 35.6 Mbits/sec 3075
> > > > > [ 5] 9.00-10.00 sec 4.20 MBytes 35.2 Mbits/sec 3039
> > > > > - - - - - - - - - - - - - - - - - - - - - - - - -
> > > > > [ ID] Interval Transfer Bitrate Jitter
> > > > > Lost/Total Datagrams
> > > > > [ 5] 0.00-10.00 sec 45.0 MBytes 37.7 Mbits/sec 0.000 ms
> > > > > 0/32584 (0%) sender
> > > > > [ 5] 0.00-10.00 sec 45.0 MBytes 37.7 Mbits/sec 0.037 ms
> > > > > 0/32573 (0%) receiver
> > > > >
> > > > > vs:
> > > > >
> > > > > [ ID] Interval Transfer Bitrate Total Datagrams
> > > > > [ 5] 0.00-1.00 sec 114 MBytes 954 Mbits/sec 82342
> > > > > [ 5] 1.00-2.00 sec 114 MBytes 955 Mbits/sec 82439
> > > > > [ 5] 2.00-3.00 sec 114 MBytes 956 Mbits/sec 82507
> > > > > [ 5] 3.00-4.00 sec 114 MBytes 955 Mbits/sec 82432
> > > > > [ 5] 4.00-5.00 sec 114 MBytes 956 Mbits/sec 82535
> > > > > [ 5] 5.00-6.00 sec 114 MBytes 953 Mbits/sec 82240
> > > > > [ 5] 6.00-7.00 sec 114 MBytes 956 Mbits/sec 82512
> > > > > [ 5] 7.00-8.00 sec 114 MBytes 956 Mbits/sec 82503
> > > > > [ 5] 8.00-9.00 sec 114 MBytes 956 Mbits/sec 82532
> > > > > [ 5] 9.00-10.00 sec 114 MBytes 956 Mbits/sec 82488
> > > > > - - - - - - - - - - - - - - - - - - - - - - - - -
> > > > > [ ID] Interval Transfer Bitrate Jitter
> > > > > Lost/Total Datagrams
> > > > > [ 5] 0.00-10.00 sec 1.11 GBytes 955 Mbits/sec 0.000 ms
> > > > > 0/824530 (0%) sender
> > > > > [ 5] 0.00-10.01 sec 1.11 GBytes 949 Mbits/sec 0.014 ms
> > > > > 4756/824530 (0.58%) receiver
> > > >
> > > > The fact that it is impacting UDP seems odd. I wonder if we don't have
> > > > a qdisc somewhere that is misbehaving and throttling the Tx. Either
> > > > that or I wonder if we are getting spammed with flow control frames.
> > >
> > > it sometimes works, it looks like the cwindow just isn't increased -
> > > that's where i started...
> > >
> > > Example:
> > > [ ID] Interval Transfer Bitrate Retr Cwnd
> > > [ 5] 0.00-1.00 sec 4.86 MBytes 40.8 Mbits/sec 0 50.9 KBytes
> > > [ 5] 1.00-2.00 sec 4.66 MBytes 39.1 Mbits/sec 0 65.0 KBytes
> > > [ 5] 2.00-3.00 sec 4.29 MBytes 36.0 Mbits/sec 0 42.4 KBytes
> > > [ 5] 3.00-4.00 sec 4.66 MBytes 39.1 Mbits/sec 0 42.4 KBytes
> > > [ 5] 4.00-5.00 sec 23.1 MBytes 194 Mbits/sec 0 1.07 MBytes
> > > [ 5] 5.00-6.00 sec 110 MBytes 923 Mbits/sec 0 761 KBytes
> > > [ 5] 6.00-7.00 sec 98.8 MBytes 828 Mbits/sec 60 806 KBytes
> > > [ 5] 7.00-8.00 sec 82.5 MBytes 692 Mbits/sec 0 812 KBytes
> > > [ 5] 8.00-9.00 sec 110 MBytes 923 Mbits/sec 92 761 KBytes
> > > [ 5] 9.00-10.00 sec 111 MBytes 933 Mbits/sec 0 755 KBytes
> > > - - - - - - - - - - - - - - - - - - - - - - - - -
> > > [ ID] Interval Transfer Bitrate Retr
> > > [ 5] 0.00-10.00 sec 554 MBytes 465 Mbits/sec 152 sender
> > > [ 5] 0.00-10.00 sec 550 MBytes 461 Mbits/sec receiver
> > >
> > > > It would be useful to include the output of just calling "ethtool
> > > > enp3s0" on the interface to verify the speed, "ethtool -a enp3s0" to
> > > > verify flow control settings, and "ethtool -S enp3s0 | grep -v :\ 0"
> > > > to output the statistics and dump anything that isn't zero.
> > >
> > > ethtool enp3s0
> > > Settings for enp3s0:
> > > Supported ports: [ TP ]
> > > Supported link modes: 10baseT/Half 10baseT/Full
> > > 100baseT/Half 100baseT/Full
> > > 1000baseT/Full
> > > Supported pause frame use: Symmetric
> > > Supports auto-negotiation: Yes
> > > Supported FEC modes: Not reported
> > > Advertised link modes: 10baseT/Half 10baseT/Full
> > > 100baseT/Half 100baseT/Full
> > > 1000baseT/Full
> > > Advertised pause frame use: Symmetric
> > > Advertised auto-negotiation: Yes
> > > Advertised FEC modes: Not reported
> > > Speed: 1000Mb/s
> > > Duplex: Full
> > > Auto-negotiation: on
> > > Port: Twisted Pair
> > > PHYAD: 1
> > > Transceiver: internal
> > > MDI-X: off (auto)
> > > Supports Wake-on: pumbg
> > > Wake-on: g
> > > Current message level: 0x00000007 (7)
> > > drv probe link
> > > Link detected: yes
> > > ---
> > > ethtool -a enp3s0
> > > Pause parameters for enp3s0:
> > > Autonegotiate: on
> > > RX: on
> > > TX: off
> > > ---
> > > ethtool -S enp3s0 |grep -v :\ 0
> > > NIC statistics:
> > > rx_packets: 15920618
> > > tx_packets: 17846725
> > > rx_bytes: 15676264423
> > > tx_bytes: 19925010639
> > > rx_broadcast: 119553
> > > tx_broadcast: 497
> > > rx_multicast: 330193
> > > tx_multicast: 18190
> > > multicast: 330193
> > > rx_missed_errors: 270102
> > > rx_long_length_errors: 6
> > > tx_tcp_seg_good: 1342561
> > > rx_long_byte_count: 15676264423
> > > rx_errors: 6
> > > rx_length_errors: 6
> > > rx_fifo_errors: 270102
> > > tx_queue_0_packets: 7651168
> > > tx_queue_0_bytes: 7823281566
> > > tx_queue_0_restart: 4920
> > > tx_queue_1_packets: 10195557
> > > tx_queue_1_bytes: 12027522118
> > > tx_queue_1_restart: 12718
> > > rx_queue_0_packets: 15920618
> > > rx_queue_0_bytes: 15612581951
> > > rx_queue_0_csum_err: 76
> > > (I've only run two runs since i reenabled the interface)
> >
> > So I am seeing three things here.
> >
> > The rx_long_length_errors are usually due to an MTU mismatch. Do you
> > have something on the network that is using jumbo frames, or is the
> > MTU on the NIC set to something smaller than what is supported on the
> > network?
>
> I'm using jumbo frames on the local network, internet side is the
> normal 1500 bytes mtu though
>
> > You are getting rx_missed_errors, that would seem to imply that the
> > DMA is not able to keep up. We may want to try disabling the L1 to see
> > if we get any boost from doing that.
>
> It used to work, I don't do benchmarks all the time and sometimes the first
> benchmarks turn out fine... so it's hard to say when this started happening...
>
> It could also be related to a bios upgrade, but I'm pretty sure I did
> successful benchmarks after that...
>
> How do I disable the l1? just echo 0 >
> /sys/bus/pci/drivers/igb/0000\:03\:00.0/link/l1_aspm ?
>
> > The last bit is that queue 0 is seeing packets with bad checksums. You
> > might want to run some tests and see where the bad checksums are
> > coming from. If they are being detected from a specific NIC such as
> > the ixgbe in your example it might point to some sort of checksum
> > error being created as a result of the NAT translation.
>
> But that should also affect A' and the A -> B -> C case, which it doesn't...
>
> It only seems to happen with higher rtt (6 hops, sub 3 ms in this case
> but still high enough somehow)
>
> > > ---
> > >
> > > > > lspci -s 03:00.0 -vvv
> > > > > 03:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network
> > > > > Connection (rev 03)
> > > > > Subsystem: ASUSTeK Computer Inc. I211 Gigabit Network Connection
> > > > > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > > > > Stepping- SERR- FastB2B- DisINTx+
> > > > > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> > > > > <TAbort- <MAbort- >SERR- <PERR- INTx-
> > > > > Latency: 0
> > > > > Interrupt: pin A routed to IRQ 57
> > > > > IOMMU group: 20
> > > > > Region 0: Memory at fc900000 (32-bit, non-prefetchable) [size=128K]
> > > > > Region 2: I/O ports at e000 [size=32]
> > > > > Region 3: Memory at fc920000 (32-bit, non-prefetchable) [size=16K]
> > > > > Capabilities: [40] Power Management version 3
> > > > > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> > > > > Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
> > > > > Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
> > > > > Address: 0000000000000000 Data: 0000
> > > > > Masking: 00000000 Pending: 00000000
> > > > > Capabilities: [70] MSI-X: Enable+ Count=5 Masked-
> > > > > Vector table: BAR=3 offset=00000000
> > > > > PBA: BAR=3 offset=00002000
> > > > > Capabilities: [a0] Express (v2) Endpoint, MSI 00
> > > > > DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
> > > > > ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
> > > > > DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
> > > > > RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
> > > > > MaxPayload 128 bytes, MaxReadReq 512 bytes
> > > > > DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
> > > > > LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency
> > > > > L0s <2us, L1 <16us
> > > > > ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
> > > > > LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
> > > > > ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> > > > > LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
> > > > > TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> > > >
> > > > PCIe wise the connection is going to be pretty tight in terms of
> > > > bandwidth. It looks like we have 2.5GT/s with only a single lane of
> > > > PCIe. In addition we are running with ASPM enabled so that means that
> > > > if we don't have enough traffic we are shutting off the one PCIe lane
> > > > we have so if we are getting bursty traffic that can get ugly.
> > >
> > > Humm... is there a way to force disable ASPM in sysfs?
> >
> > Actually the easiest way to do this is to just use setpci.
> >
> > You should be able to dump the word containing the setting via:
> > # setpci -s 3:00.0 0xB0.w
> > 0042
> > # setpci -s 3:00.0 0xB0.w=0040
> >
> > Basically what you do is clear the lower 3 bits of the value so in
> > this case that means replacing the 2 with a 0 based on the output of
> > the first command.
>
> Well... I'll be damned... I used to force enable ASPM... this must be
> related to the change in PCIe bus ASPM
> Perhaps disable ASPM if there is only one link?
Is there any specific reason why you are enabling ASPM? Is this system
a laptop where you are trying to conserve power when on battery? If
not disabling it probably won't hurt things too much since the power
consumption for a 2.5GT/s link operating in a width of one shouldn't
bee too high. Otherwise you are likely going to end up paying the
price for getting the interface out of L1 when the traffic goes idle
so you are going to see flows that get bursty paying a heavy penalty
when they start dropping packets.
It is also possible this could be something that changed with the
physical PCIe link. Basically L1 works by powering down the link when
idle, and then powering it back up when there is activity. The problem
is bringing it back up can sometimes be a challenge when the physical
link starts to go faulty. I know I have seen that in some cases it can
even result in the device falling off of the PCIe bus if the link
training fails.
> [ ID] Interval Transfer Bitrate Retr Cwnd
> [ 5] 0.00-1.00 sec 113 MBytes 950 Mbits/sec 31 710 KBytes
> [ 5] 1.00-2.00 sec 110 MBytes 923 Mbits/sec 135 626 KBytes
> [ 5] 2.00-3.00 sec 112 MBytes 944 Mbits/sec 18 713 KBytes
> [ 5] 3.00-4.00 sec 111 MBytes 933 Mbits/sec 0 798 KBytes
> [ 5] 4.00-5.00 sec 111 MBytes 933 Mbits/sec 0 721 KBytes
> [ 5] 5.00-6.00 sec 112 MBytes 944 Mbits/sec 31 800 KBytes
> [ 5] 6.00-7.00 sec 111 MBytes 933 Mbits/sec 0 730 KBytes
> [ 5] 7.00-8.00 sec 111 MBytes 933 Mbits/sec 19 730 KBytes
> [ 5] 8.00-9.00 sec 111 MBytes 933 Mbits/sec 0 701 KBytes
> [ 5] 9.00-10.00 sec 112 MBytes 944 Mbits/sec 12 701 KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bitrate Retr
> [ 5] 0.00-10.00 sec 1.09 GBytes 937 Mbits/sec 246 sender
> [ 5] 0.00-10.01 sec 1.09 GBytes 933 Mbits/sec receiver
>
> [ ID] Interval Transfer Bitrate Retr Cwnd
> [ 5] 0.00-1.00 sec 114 MBytes 956 Mbits/sec 0 749 KBytes
> [ 5] 1.00-2.00 sec 111 MBytes 933 Mbits/sec 30 766 KBytes
> [ 5] 2.00-3.00 sec 112 MBytes 944 Mbits/sec 7 749 KBytes
> [ 5] 3.00-4.00 sec 111 MBytes 933 Mbits/sec 11 707 KBytes
> [ 5] 4.00-5.00 sec 111 MBytes 933 Mbits/sec 2 699 KBytes
> [ 5] 5.00-6.00 sec 111 MBytes 933 Mbits/sec 8 699 KBytes
> [ 5] 6.00-7.00 sec 112 MBytes 944 Mbits/sec 1 953 KBytes
> [ 5] 7.00-8.00 sec 111 MBytes 933 Mbits/sec 0 701 KBytes
> [ 5] 8.00-9.00 sec 111 MBytes 933 Mbits/sec 26 707 KBytes
> [ 5] 9.00-10.00 sec 112 MBytes 944 Mbits/sec 2 1.07 MBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bitrate Retr
> [ 5] 0.00-10.00 sec 1.09 GBytes 939 Mbits/sec 87 sender
> [ 5] 0.00-10.00 sec 1.09 GBytes 934 Mbits/sec receiver
>
> [ ID] Interval Transfer Bitrate Retr Cwnd
> [ 5] 0.00-1.00 sec 114 MBytes 953 Mbits/sec 16 908 KBytes
> [ 5] 1.00-2.00 sec 112 MBytes 944 Mbits/sec 0 693 KBytes
> [ 5] 2.00-3.00 sec 111 MBytes 933 Mbits/sec 0 713 KBytes
> [ 5] 3.00-4.00 sec 111 MBytes 933 Mbits/sec 0 687 KBytes
> [ 5] 4.00-5.00 sec 112 MBytes 944 Mbits/sec 15 687 KBytes
> [ 5] 5.00-6.00 sec 111 MBytes 933 Mbits/sec 2 888 KBytes
> [ 5] 6.00-7.00 sec 111 MBytes 933 Mbits/sec 17 696 KBytes
> [ 5] 7.00-8.00 sec 111 MBytes 933 Mbits/sec 0 758 KBytes
> [ 5] 8.00-9.00 sec 111 MBytes 933 Mbits/sec 31 749 KBytes
> [ 5] 9.00-10.00 sec 112 MBytes 944 Mbits/sec 0 792 KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bitrate Retr
> [ 5] 0.00-10.00 sec 1.09 GBytes 938 Mbits/sec 81 sender
> [ 5] 0.00-10.00 sec 1.09 GBytes 934 Mbits/sec receiver
>
> [ ID] Interval Transfer Bitrate Retr Cwnd
> [ 5] 0.00-1.00 sec 114 MBytes 956 Mbits/sec 0 747 KBytes
> [ 5] 1.00-2.00 sec 111 MBytes 933 Mbits/sec 0 744 KBytes
> [ 5] 2.00-3.00 sec 112 MBytes 944 Mbits/sec 12 1.18 MBytes
> [ 5] 3.00-4.00 sec 111 MBytes 933 Mbits/sec 2 699 KBytes
> [ 5] 4.00-5.00 sec 111 MBytes 933 Mbits/sec 28 699 KBytes
> [ 5] 5.00-6.00 sec 112 MBytes 944 Mbits/sec 0 684 KBytes
> [ 5] 6.00-7.00 sec 111 MBytes 933 Mbits/sec 0 741 KBytes
> [ 5] 7.00-8.00 sec 111 MBytes 933 Mbits/sec 3 687 KBytes
> [ 5] 8.00-9.00 sec 111 MBytes 933 Mbits/sec 22 699 KBytes
> [ 5] 9.00-10.00 sec 111 MBytes 933 Mbits/sec 11 707 KBytes
> - - - - - - - - - - - - - - - - - - - - - - - - -
> [ ID] Interval Transfer Bitrate Retr
> [ 5] 0.00-10.00 sec 1.09 GBytes 938 Mbits/sec 78 sender
> [ 5] 0.00-10.01 sec 1.09 GBytes 934 Mbits/sec receiver
> ---
>
> ethtool -S enp3s0 |grep -v ": 0"
> NIC statistics:
> rx_packets: 16303520
> tx_packets: 21602840
> rx_bytes: 15711958157
> tx_bytes: 25599009212
> rx_broadcast: 122212
> tx_broadcast: 530
> rx_multicast: 333489
> tx_multicast: 18446
> multicast: 333489
> rx_missed_errors: 270143
> rx_long_length_errors: 6
> tx_tcp_seg_good: 1342561
> rx_long_byte_count: 15711958157
> rx_errors: 6
> rx_length_errors: 6
> rx_fifo_errors: 270143
> tx_queue_0_packets: 8963830
> tx_queue_0_bytes: 9803196683
> tx_queue_0_restart: 4920
> tx_queue_1_packets: 12639010
> tx_queue_1_bytes: 15706576814
> tx_queue_1_restart: 12718
> rx_queue_0_packets: 16303520
> rx_queue_0_bytes: 15646744077
> rx_queue_0_csum_err: 76
Okay, so this result still has the same length and checksum errors,
were you resetting the system/statistics between runs?
Powered by blists - more mailing lists