| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20201021135140.51300-2-alexandru.ardelean@analog.com>
Date: Wed, 21 Oct 2020 16:51:40 +0300
From: Alexandru Ardelean <alexandru.ardelean@...log.com>
To: <netdev@...r.kernel.org>, <linux-kernel@...r.kernel.org>
CC: <alexaundru.ardelean@...log.com>, <andrew@...n.ch>,
<hkallweit1@...il.com>, <linux@...linux.org.uk>,
<davem@...emloft.net>, <ardeleanalex@...il.com>, <kuba@...nel.org>,
Alexandru Ardelean <alexandru.ardelean@...log.com>
Subject: [PATCH 2/2] net: phy: adin: implement cable-test support
The ADIN1300/ADIN1200 support cable diagnostics using TDR.
The cable fault detection is automatically run on all four pairs looking at
all combinations of pair faults by first putting the PHY in standby (clear
the LINK_EN bit, PHY_CTRL_3 register, Address 0x0017) and then enabling the
diagnostic clock (set the DIAG_CLK_EN bit, PHY_CTRL_1 register, Address
0x0012).
Cable diagnostics can then be run (set the CDIAG_RUN bit in the
CDIAG_RUN register, Address 0xBA1B). The results are reported for each pair
in the cable diagnostics results registers, CDIAG_DTLD_RSLTS_0,
CDIAG_DTLD_RSLTS_1, CDIAG_DTLD_RSLTS_2, and CDIAG_DTLD_RSLTS_3, Address
0xBA1D to Address 0xBA20).
The distance to the first fault for each pair is reported in the cable
fault distance registers, CDIAG_FLT_DIST_0, CDIAG_FLT_DIST_1,
CDIAG_FLT_DIST_2, and CDIAG_FLT_DIST_3, Address 0xBA21 to Address 0xBA24).
This change implements support for this using phylib's cable-test support.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@...log.com>
---
drivers/net/phy/adin.c | 138 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 138 insertions(+)
diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
index 619d36685b5d..3e66f97c7611 100644
--- a/drivers/net/phy/adin.c
+++ b/drivers/net/phy/adin.c
@@ -8,6 +8,7 @@
#include <linux/bitfield.h>
#include <linux/delay.h>
#include <linux/errno.h>
+#include <linux/ethtool_netlink.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/mii.h>
@@ -70,6 +71,31 @@
#define ADIN1300_CLOCK_STOP_REG 0x9400
#define ADIN1300_LPI_WAKE_ERR_CNT_REG 0xa000
+#define ADIN1300_CDIAG_RUN 0xba1b
+#define ADIN1300_CDIAG_RUN_EN BIT(0)
+
+/*
+ * The XSIM3/2/1 and XSHRT3/2/1 are actually relative.
+ * For CDIAG_DTLD_RSLTS(0) it's ADIN1300_CDIAG_RSLT_XSIM3/2/1
+ * For CDIAG_DTLD_RSLTS(1) it's ADIN1300_CDIAG_RSLT_XSIM3/2/0
+ * For CDIAG_DTLD_RSLTS(2) it's ADIN1300_CDIAG_RSLT_XSIM3/1/0
+ * For CDIAG_DTLD_RSLTS(3) it's ADIN1300_CDIAG_RSLT_XSIM2/1/0
+ */
+#define ADIN1300_CDIAG_DTLD_RSLTS(x) (0xba1d + (x))
+#define ADIN1300_CDIAG_RSLT_BUSY BIT(10)
+#define ADIN1300_CDIAG_RSLT_XSIM3 BIT(9)
+#define ADIN1300_CDIAG_RSLT_XSIM2 BIT(8)
+#define ADIN1300_CDIAG_RSLT_XSIM1 BIT(7)
+#define ADIN1300_CDIAG_RSLT_SIM BIT(6)
+#define ADIN1300_CDIAG_RSLT_XSHRT3 BIT(5)
+#define ADIN1300_CDIAG_RSLT_XSHRT2 BIT(4)
+#define ADIN1300_CDIAG_RSLT_XSHRT1 BIT(3)
+#define ADIN1300_CDIAG_RSLT_SHRT BIT(2)
+#define ADIN1300_CDIAG_RSLT_OPEN BIT(1)
+#define ADIN1300_CDIAG_RSLT_GOOD BIT(0)
+
+#define ADIN1300_CDIAG_FLT_DIST(x) (0xba21 + (x))
+
#define ADIN1300_GE_SOFT_RESET_REG 0xff0c
#define ADIN1300_GE_SOFT_RESET BIT(0)
@@ -741,10 +767,117 @@ static int adin_probe(struct phy_device *phydev)
return 0;
}
+static int adin_cable_test_start(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_clear_bits(phydev, ADIN1300_PHY_CTRL3, ADIN1300_LINKING_EN);
+ if (ret < 0)
+ return ret;
+
+ ret = phy_clear_bits(phydev, ADIN1300_PHY_CTRL1, ADIN1300_DIAG_CLK_EN);
+ if (ret < 0)
+ return ret;
+
+ /* wait a bit for the clock to stabilize */
+ msleep(50);
+
+ return phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_CDIAG_RUN,
+ ADIN1300_CDIAG_RUN_EN);
+}
+
+static int adin_cable_test_report_trans(int result)
+{
+ int mask;
+
+ if (result & ADIN1300_CDIAG_RSLT_GOOD)
+ return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+ if (result & ADIN1300_CDIAG_RSLT_OPEN)
+ return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+
+ /* short with other pairs */
+ mask = ADIN1300_CDIAG_RSLT_XSHRT3 |
+ ADIN1300_CDIAG_RSLT_XSHRT2 |
+ ADIN1300_CDIAG_RSLT_XSHRT1;
+ if (result & mask)
+ return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
+
+ if (result & ADIN1300_CDIAG_RSLT_SHRT)
+ return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+
+ return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+}
+
+static int adin_cable_test_report_pair(struct phy_device *phydev,
+ unsigned int pair)
+{
+ int fault_rslt;
+ int ret;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND1,
+ ADIN1300_CDIAG_DTLD_RSLTS(pair));
+ if (ret < 0)
+ return ret;
+
+ fault_rslt = adin_cable_test_report_trans(ret);
+
+ ret = ethnl_cable_test_result(phydev, pair, fault_rslt);
+ if (ret < 0)
+ return ret;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND1,
+ ADIN1300_CDIAG_FLT_DIST(pair));
+ if (ret < 0)
+ return ret;
+
+ switch (fault_rslt) {
+ case ETHTOOL_A_CABLE_RESULT_CODE_OPEN:
+ case ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT:
+ case ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT:
+ return ethnl_cable_test_fault_length(phydev, pair, ret * 100);
+ default:
+ return 0;
+ }
+}
+
+static int adin_cable_test_report(struct phy_device *phydev)
+{
+ unsigned int pair;
+ int ret;
+
+ for (pair = ETHTOOL_A_CABLE_PAIR_A; pair <= ETHTOOL_A_CABLE_PAIR_D; pair++) {
+ ret = adin_cable_test_report_pair(phydev, pair);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int adin_cable_test_get_status(struct phy_device *phydev,
+ bool *finished)
+{
+ int ret;
+
+ *finished = false;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_CDIAG_RUN);
+ if (ret < 0)
+ return ret;
+
+ if (ret & ADIN1300_CDIAG_RUN_EN)
+ return 0;
+
+ *finished = true;
+
+ return adin_cable_test_report(phydev);
+}
+
static struct phy_driver adin_driver[] = {
{
PHY_ID_MATCH_MODEL(PHY_ID_ADIN1200),
.name = "ADIN1200",
+ .flags = PHY_POLL_CABLE_TEST,
.probe = adin_probe,
.config_init = adin_config_init,
.soft_reset = adin_soft_reset,
@@ -761,10 +894,13 @@ static struct phy_driver adin_driver[] = {
.suspend = genphy_suspend,
.read_mmd = adin_read_mmd,
.write_mmd = adin_write_mmd,
+ .cable_test_start = adin_cable_test_start,
+ .cable_test_get_status = adin_cable_test_get_status,
},
{
PHY_ID_MATCH_MODEL(PHY_ID_ADIN1300),
.name = "ADIN1300",
+ .flags = PHY_POLL_CABLE_TEST,
.probe = adin_probe,
.config_init = adin_config_init,
.soft_reset = adin_soft_reset,
@@ -781,6 +917,8 @@ static struct phy_driver adin_driver[] = {
.suspend = genphy_suspend,
.read_mmd = adin_read_mmd,
.write_mmd = adin_write_mmd,
+ .cable_test_start = adin_cable_test_start,
+ .cable_test_get_status = adin_cable_test_get_status,
},
};
--
2.17.1
Powered by blists - more mailing lists