| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <72671f94d25e91903f68fa8f00678eb678855b35.1603907878.git.gnault@redhat.com>
Date: Wed, 28 Oct 2020 19:05:14 +0100
From: Guillaume Nault <gnault@...hat.com>
To: David Miller <davem@...emloft.net>,
Jakub Kicinski <kuba@...nel.org>
Cc: netdev@...r.kernel.org, Martin Varghese <martin.varghese@...ia.com>
Subject: [PATCH net] selftests: add test script for bareudp tunnels
Test different encapsulation modes of the bareudp module:
* Unicast MPLS,
* IPv4 only,
* IPv4 in multiproto mode (that is, IPv4 and IPv6),
* IPv6.
Each mode is tested with both an IPv4 and an IPv6 underlay.
Signed-off-by: Guillaume Nault <gnault@...hat.com>
---
tools/testing/selftests/net/Makefile | 1 +
tools/testing/selftests/net/bareudp.sh | 523 +++++++++++++++++++++++++
2 files changed, 524 insertions(+)
create mode 100755 tools/testing/selftests/net/bareudp.sh
diff --git a/tools/testing/selftests/net/Makefile b/tools/testing/selftests/net/Makefile
index ef352477cac6..fa5fa425d148 100644
--- a/tools/testing/selftests/net/Makefile
+++ b/tools/testing/selftests/net/Makefile
@@ -21,6 +21,7 @@ TEST_PROGS += rxtimestamp.sh
TEST_PROGS += devlink_port_split.py
TEST_PROGS += drop_monitor_tests.sh
TEST_PROGS += vrf_route_leaking.sh
+TEST_PROGS += bareudp.sh
TEST_PROGS_EXTENDED := in_netns.sh
TEST_GEN_FILES = socket nettest
TEST_GEN_FILES += psock_fanout psock_tpacket msg_zerocopy reuseport_addr_any
diff --git a/tools/testing/selftests/net/bareudp.sh b/tools/testing/selftests/net/bareudp.sh
new file mode 100755
index 000000000000..e565900789c0
--- /dev/null
+++ b/tools/testing/selftests/net/bareudp.sh
@@ -0,0 +1,523 @@
+#!/bin/sh
+# SPDX-License-Identifier: GPL-2.0
+
+# Test various bareudp tunnel configurations.
+#
+# The bareudp module allows to tunnel network protocols like IP or MPLS over
+# UDP, without adding any intermediate header. This scripts tests several
+# configurations of bareudp (using IPv4 or IPv6 as underlay and transporting
+# IPv4, IPv6 or MPLS packets on the overlay).
+#
+# Network topology:
+#
+# * A chain of 4 network namespaces, connected with veth pairs. Each veth
+# is assigned an IPv4 and an IPv6 address. A host-route allows a veth to
+# join its peer.
+#
+# * NS0 and NS3 are at the extremities of the chain. They have an additional
+# IPv4 and IPv6 address on their loopback device. A route is added to NS0
+# and NS3, so that they can communicate using these "overlay" IP addresses.
+# For IPv4 and IPv6 reachability tests, the route simply sets the peer's
+# veth address as gateway. For MPLS reachability tests, an MPLS header is
+# also pushed before the IP header.
+#
+# * NS1 and NS2 are the intermediate namespaces. They use a bareudp device to
+# encapsulate the traffic between NS0 and NS3 into UDP.
+#
+# +-----------------------------------------------------------------------+
+# | NS0 |
+# | |
+# | lo: |
+# | * IPv4 address: 192.0.2.100/32 |
+# | * IPv6 address: 2001:db8::100/128 |
+# | * IPv4 route: 192.0.2.103/32 reachable via 192.0.2.11 |
+# | * IPv6 route: 2001:db8::103/128 reachable via 2001:db8::11 |
+# | (optionally MPLS encapsulated, depending on test) |
+# | |
+# | veth01: |
+# | ^ * IPv4 address: 192.0.2.10, peer 192.0.2.11/32 |
+# | | * IPv6 address: 2001:db8::10, peer 2001:db8::11/128 |
+# | | |
+# +---+-------------------------------------------------------------------+
+# |
+# | Traffic type: IP or MPLS (depending on test)
+# |
+# +---+-------------------------------------------------------------------+
+# | | NS1 |
+# | | |
+# | v |
+# | veth10: |
+# | * IPv4 address: 192.0.2.11, peer 192.0.2.10/32 |
+# | * IPv6 address: 2001:db8::11, peer 2001:db8::10/128 |
+# | |
+# | bareudp_ns1: |
+# | * Encapsulate IP or MPLS packets received on veth10 into UDP |
+# | and send the resulting packets through veth12. |
+# | * Decapsulate bareudp packets (either IP or MPLS, over UDP) |
+# | received on veth12 and send the inner packets through veth10. |
+# | |
+# | veth12: |
+# | ^ * IPv4 address: 192.0.2.21, peer 192.0.2.22/32 |
+# | | * IPv6 address: 2001:db8::21, peer 2001:db8::22/128 |
+# | | |
+# +---+-------------------------------------------------------------------+
+# |
+# | Traffic type: IP or MPLS (depending on test), over UDP
+# |
+# +---+-------------------------------------------------------------------+
+# | | NS2 |
+# | | |
+# | v |
+# | veth21: |
+# | * IPv4 address: 192.0.2.22, peer 192.0.2.21/32 |
+# | * IPv6 address: 2001:db8::22, peer 2001:db8::21/128 |
+# | |
+# | bareudp_ns2: |
+# | * Decapsulate bareudp packets (either IP or MPLS, over UDP) |
+# | received on veth21 and send the inner packets through veth23. |
+# | * Encapsulate IP or MPLS packets received on veth23 into UDP |
+# | and send the resulting packets through veth21. |
+# | |
+# | veth23: |
+# | ^ * IPv4 address: 192.0.2.32, peer 192.0.2.33/32 |
+# | | * IPv6 address: 2001:db8::32, peer 2001:db8::33/128 |
+# | | |
+# +---+-------------------------------------------------------------------+
+# |
+# | Traffic type: IP or MPLS (depending on test)
+# |
+# +---+-------------------------------------------------------------------+
+# | | NS3 |
+# | v |
+# | veth32: |
+# | * IPv4 address: 192.0.2.33, peer 192.0.2.32/32 |
+# | * IPv6 address: 2001:db8::33, peer 2001:db8::32/128 |
+# | |
+# | lo: |
+# | * IPv4 address: 192.0.2.103/32 |
+# | * IPv6 address: 2001:db8::103/128 |
+# | * IPv4 route: 192.0.2.100/32 reachable via 192.0.2.32 |
+# | * IPv6 route: 2001:db8::100/128 reachable via 2001:db8::32 |
+# | (optionally MPLS encapsulated, depending on test) |
+# | |
+# +-----------------------------------------------------------------------+
+
+ERR=4 # Return 4 by default, which is the SKIP code for kselftest
+PAUSE_ON_FAIL="no"
+
+readonly NS0=$(mktemp -u ns0-XXXXXXXX)
+readonly NS1=$(mktemp -u ns1-XXXXXXXX)
+readonly NS2=$(mktemp -u ns2-XXXXXXXX)
+readonly NS3=$(mktemp -u ns3-XXXXXXXX)
+
+# Check if ping is usable for IPv6. Use ping6 if it isn't.
+ping -w 1 -c 1 ::1 > /dev/null 2>&1 && PING6="ping" || PING6="ping6"
+
+# Exit the script after having removed the network namespaces it created
+#
+# Parameters:
+#
+# * The list of network namespaces to delete before exiting.
+#
+exit_cleanup()
+{
+ for ns in "$@"; do
+ ip netns delete "${ns}" 2>/dev/null || true
+ done
+
+ if [ "${ERR}" -eq 4 ]; then
+ printf "Error: Setting up the testing environment failed.\n" >&2
+ fi
+
+ exit "${ERR}"
+}
+
+# Create the four network namespaces used by the script (NS0, NS1, NS2 and NS3)
+#
+# New namespaces are cleaned up manually in case of error, to ensure that we're
+# not going to delete pre-existing namespaces.
+create_namespaces()
+{
+ ip netns add "${NS0}" || exit_cleanup
+ ip netns add "${NS1}" || exit_cleanup "${NS0}"
+ ip netns add "${NS2}" || exit_cleanup "${NS0}" "${NS1}"
+ ip netns add "${NS3}" || exit_cleanup "${NS0}" "${NS1}" "${NS2}"
+}
+
+# The trap function handler
+#
+exit_cleanup_all()
+{
+ exit_cleanup "${NS0}" "${NS1}" "${NS2}" "${NS3}"
+}
+
+# Configure a network interface using a host route
+#
+# Parameters
+#
+# * $1: the netns the network interface resides in,
+# * $2: the network interface name,
+# * $3: the local IPv4 address to assign to this interface,
+# * $4: the IPv4 address of the remote network interface,
+# * $5: the local IPv6 address to assign to this interface,
+# * $6: the IPv6 address of the remote network interface.
+#
+iface_config()
+{
+ local NS="${1}"; readonly NS
+ local DEV="${2}"; readonly DEV
+ local LOCAL_IP4="${3}"; readonly LOCAL_IP4
+ local PEER_IP4="${4}"; readonly PEER_IP4
+ local LOCAL_IP6="${5}"; readonly LOCAL_IP6
+ local PEER_IP6="${6}"; readonly PEER_IP6
+
+ ip -netns "${NS}" link set dev "${DEV}" up
+ ip -netns "${NS}" address add dev "${DEV}" "${LOCAL_IP4}" peer "${PEER_IP4}"
+ ip -netns "${NS}" address add dev "${DEV}" "${LOCAL_IP6}" peer "${PEER_IP6}" nodad
+}
+
+# Create base networking topology:
+#
+# * set up the loopback device in all network namespaces (NS0..NS3),
+# * set up a veth pair to connect each netns in sequence (NS0 with NS1,
+# NS1 with NS2, etc.),
+# * add and IPv4 and an IPv6 address on each veth interface.
+#
+setup_underlay()
+{
+ for ns in "${NS0}" "${NS1}" "${NS2}" "${NS3}"; do
+ ip -netns "${ns}" link set dev lo up
+ done;
+
+ ip link add name veth01 netns "${NS0}" type veth peer name veth10 netns "${NS1}"
+ ip link add name veth12 netns "${NS1}" type veth peer name veth21 netns "${NS2}"
+ ip link add name veth23 netns "${NS2}" type veth peer name veth32 netns "${NS3}"
+ iface_config "${NS0}" veth01 192.0.2.10 192.0.2.11/32 2001:db8::10 2001:db8::11/128
+ iface_config "${NS1}" veth10 192.0.2.11 192.0.2.10/32 2001:db8::11 2001:db8::10/128
+ iface_config "${NS1}" veth12 192.0.2.21 192.0.2.22/32 2001:db8::21 2001:db8::22/128
+ iface_config "${NS2}" veth21 192.0.2.22 192.0.2.21/32 2001:db8::22 2001:db8::21/128
+ iface_config "${NS2}" veth23 192.0.2.32 192.0.2.33/32 2001:db8::32 2001:db8::33/128
+ iface_config "${NS3}" veth32 192.0.2.33 192.0.2.32/32 2001:db8::33 2001:db8::32/128
+}
+
+# Set up the parts of the overlay network that are common to all tests:
+#
+# * add an IPv4 and an IPv6 overlay network address on the loopback device of
+# the edge namespaces,
+# * enable IP forwarding in the intermediate namespaces.
+#
+# We can't configure the MPLS syctls yet as the mpls_router module may not be
+# loaded at this point.
+#
+setup_overlay_common()
+{
+ ip -netns "${NS0}" address add 192.0.2.100/32 dev lo
+ ip -netns "${NS3}" address add 192.0.2.103/32 dev lo
+ ip -netns "${NS0}" address add 2001:db8::100/128 dev lo
+ ip -netns "${NS3}" address add 2001:db8::103/128 dev lo
+
+ ip netns exec "${NS1}" sysctl -qw net.ipv6.conf.all.forwarding=1
+ ip netns exec "${NS2}" sysctl -qw net.ipv6.conf.all.forwarding=1
+ ip netns exec "${NS1}" sysctl -qw net.ipv4.ip_forward=1
+ ip netns exec "${NS2}" sysctl -qw net.ipv4.ip_forward=1
+}
+
+# Run "ping" from NS0 and print the result
+#
+# Parameters:
+#
+# * $1: the variant of ping to use (normally either "ping" or "ping6"),
+# * $2: the IP address to ping,
+# * $3: a human readable description of the purpose of the test.
+#
+# If the test fails and PAUSE_ON_FAIL is active, the user is given the
+# possibility to continue with the next test or to quit immediately.
+#
+ping_test_one()
+{
+ local PING="$1"; readonly PING
+ local IP="$2"; readonly IP
+ local MSG="$3"; readonly MSG
+ local RET
+
+ printf "TEST: %-60s " "${MSG}"
+
+ set +e
+ ip netns exec "${NS0}" "${PING}" -w 5 -c 1 "${IP}" > /dev/null 2>&1
+ RET=$?
+ set -e
+
+ if [ "${RET}" -eq 0 ]; then
+ printf "[ OK ]\n"
+ else
+ ERR=1
+ printf "[FAIL]\n"
+ if [ "${PAUSE_ON_FAIL}" = "yes" ]; then
+ printf "\nHit enter to continue, 'q' to quit\n"
+ read a
+ if [ "$a" = "q" ]; then
+ exit 1
+ fi
+ fi
+ fi
+}
+
+# Run reachability tests
+#
+# Parameters:
+#
+# * $1: human readable string describing the underlay protocol.
+#
+# $IPV4, $IPV6, $MPLS_UC and $MULTIPROTO are inherited from the calling
+# function.
+#
+ping_test()
+{
+ local UNDERLAY="$1"; readonly UNDERLAY
+ local MODE
+ local MSG
+
+ if [ "${MULTIPROTO}" = "multiproto" ]; then
+ MODE=" (multiproto mode)"
+ else
+ MODE=""
+ fi
+
+ if [ $IPV4 ]; then
+ ping_test_one "ping" "192.0.2.103" "IPv4 packets over ${UNDERLAY}${MODE}"
+ fi
+ if [ $IPV6 ]; then
+ ping_test_one "${PING6}" "2001:db8::103" "IPv6 packets over ${UNDERLAY}${MODE}"
+ fi
+ if [ $MPLS_UC ]; then
+ ping_test_one "${PING6}" "2001:db8::103" "Unicast MPLS packets over ${UNDERLAY}${MODE}"
+ fi
+}
+
+# Set up a bareudp overlay and run reachability tests over IPv4 and IPv6
+#
+# Parameters:
+#
+# * $1: the packet type (protocol) to be handled by bareudp,
+# * $2: a flag to activate or deactivate bareudp's "multiproto" mode.
+#
+test_overlay()
+{
+ local ETHERTYPE="$1"; readonly ETHERTYPE
+ local MULTIPROTO="$2"; readonly MULTIPROTO
+ local IPV4
+ local IPV6
+ local MPLS_UC
+
+ case "${ETHERTYPE}" in
+ "ipv4")
+ IPV4="ipv4"
+ if [ "${MULTIPROTO}" = "multiproto" ]; then
+ IPV6="ipv6"
+ else
+ IPV6=""
+ fi
+ MPLS_UC=""
+ ;;
+ "ipv6")
+ IPV6="ipv6"
+ IPV4=""
+ MPLS_UC=""
+ ;;
+ "mpls_uc")
+ MPLS_UC="mpls_uc"
+ IPV4=""
+ IPV6=""
+ ;;
+ *)
+ exit 1
+ ;;
+ esac
+ readonly IPV4
+ readonly IPV6
+ readonly MPLS_UC
+
+ # Create the bareudp devices in the intermediate namespaces
+ ip -netns "${NS1}" link add name bareudp_ns1 up type bareudp dstport 6635 ethertype "${ETHERTYPE}" "${MULTIPROTO}"
+ ip -netns "${NS2}" link add name bareudp_ns2 up type bareudp dstport 6635 ethertype "${ETHERTYPE}" "${MULTIPROTO}"
+
+ # Prepare the ingress qdisc in the intermediate namespaces
+ tc -netns "${NS1}" qdisc add dev veth10 ingress
+ tc -netns "${NS2}" qdisc add dev veth23 ingress
+
+ # IPv4 over UDPv4
+ if [ $IPV4 ]; then
+ # Route the overlay addresses in the edge namespaces
+ ip -netns "${NS0}" route add 192.0.2.103/32 src 192.0.2.100 via 192.0.2.11
+ ip -netns "${NS3}" route add 192.0.2.100/32 src 192.0.2.103 via 192.0.2.32
+
+ # Route the overlay addresses in the intermediate namespaces
+ # (used after bareudp decapsulation)
+ ip -netns "${NS1}" route add 192.0.2.100/32 via 192.0.2.10
+ ip -netns "${NS2}" route add 192.0.2.103/32 via 192.0.2.33
+
+ # Encapsulation instructions for bareudp over IPv4
+ tc -netns "${NS1}" filter add dev veth10 ingress protocol ipv4 \
+ flower dst_ip 192.0.2.103/32 \
+ action tunnel_key set src_ip 192.0.2.21 dst_ip 192.0.2.22 id 0 \
+ action mirred egress redirect dev bareudp_ns1
+ tc -netns "${NS2}" filter add dev veth23 ingress protocol ipv4 \
+ flower dst_ip 192.0.2.100/32 \
+ action tunnel_key set src_ip 192.0.2.22 dst_ip 192.0.2.21 id 0 \
+ action mirred egress redirect dev bareudp_ns2
+ fi
+
+ # IPv6 over UDPv4
+ if [ $IPV6 ]; then
+ # Route the overlay addresses in the edge namespaces
+ ip -netns "${NS0}" route add 2001:db8::103/128 src 2001:db8::100 via 2001:db8::11
+ ip -netns "${NS3}" route add 2001:db8::100/128 src 2001:db8::103 via 2001:db8::32
+
+ # Route the overlay addresses in the intermediate namespaces
+ # (used after bareudp decapsulation)
+ ip -netns "${NS1}" route add 2001:db8::100/128 via 2001:db8::10
+ ip -netns "${NS2}" route add 2001:db8::103/128 via 2001:db8::33
+
+ # Encapsulation instructions for bareudp over IPv4
+ tc -netns "${NS1}" filter add dev veth10 ingress protocol ipv6 \
+ flower dst_ip 2001:db8::103/128 \
+ action tunnel_key set src_ip 192.0.2.21 dst_ip 192.0.2.22 id 0 \
+ action mirred egress redirect dev bareudp_ns1
+ tc -netns "${NS2}" filter add dev veth23 ingress protocol ipv6 \
+ flower dst_ip 2001:db8::100/128 \
+ action tunnel_key set src_ip 192.0.2.22 dst_ip 192.0.2.21 id 0 \
+ action mirred egress redirect dev bareudp_ns2
+ fi
+
+ # MPLS (unicast) over UDPv4
+ if [ $MPLS_UC ]; then
+ # Route the overlay addresses in the edge namespaces
+ ip -netns "${NS0}" route add 2001:db8::103/128 src 2001:db8::100 encap mpls 103 via 2001:db8::11
+ ip -netns "${NS3}" route add 2001:db8::100/128 src 2001:db8::103 encap mpls 100 via 2001:db8::32
+
+ # Accept incoming MPLS packets in the intermediate namespaces
+ ip netns exec "${NS1}" sysctl -qw net.mpls.platform_labels=1000
+ ip netns exec "${NS2}" sysctl -qw net.mpls.platform_labels=1000
+ ip netns exec "${NS1}" sysctl -qw net.mpls.conf.bareudp_ns1.input=1
+ ip netns exec "${NS2}" sysctl -qw net.mpls.conf.bareudp_ns2.input=1
+
+ # Route the MPLS packets in the intermediate namespaces
+ # (used after bareudp decapsulation)
+ ip -netns "${NS1}" -family mpls route add 100 via inet6 2001:db8::10
+ ip -netns "${NS2}" -family mpls route add 103 via inet6 2001:db8::33
+
+ # Encapsulation instructions for bareudp over IPv4
+ tc -netns "${NS1}" filter add dev veth10 ingress protocol mpls_uc \
+ flower mpls_label 103 \
+ action tunnel_key set src_ip 192.0.2.21 dst_ip 192.0.2.22 id 0 \
+ action mirred egress redirect dev bareudp_ns1
+ tc -netns "${NS2}" filter add dev veth23 ingress protocol mpls_uc \
+ flower mpls_label 100 \
+ action tunnel_key set src_ip 192.0.2.22 dst_ip 192.0.2.21 id 0 \
+ action mirred egress redirect dev bareudp_ns2
+ fi
+
+ # Test IPv4 underlay
+ ping_test "UDPv4"
+
+ # Cleanup bareudp encapsulation instructions, as they were specific to
+ # the IPv4 underlay, before setting up and testing the IPv6 underlay
+ tc -netns "${NS1}" filter delete dev veth10 ingress
+ tc -netns "${NS2}" filter delete dev veth23 ingress
+
+ # IPv4 over UDPv6
+ if [ $IPV4 ]; then
+ # New encapsulation instructions for bareudp over IPv6
+ tc -netns "${NS1}" filter add dev veth10 ingress protocol ipv4 \
+ flower dst_ip 192.0.2.103/32 \
+ action tunnel_key set src_ip 2001:db8::21 dst_ip 2001:db8::22 id 0 \
+ action mirred egress redirect dev bareudp_ns1
+ tc -netns "${NS2}" filter add dev veth23 ingress protocol ipv4 \
+ flower dst_ip 192.0.2.100/32 \
+ action tunnel_key set src_ip 2001:db8::22 dst_ip 2001:db8::21 id 0 \
+ action mirred egress redirect dev bareudp_ns2
+ fi
+
+ # IPv6 over UDPv6
+ if [ $IPV6 ]; then
+ # New encapsulation instructions for bareudp over IPv6
+ tc -netns "${NS1}" filter add dev veth10 ingress protocol ipv6 \
+ flower dst_ip 2001:db8::103/128 \
+ action tunnel_key set src_ip 2001:db8::21 dst_ip 2001:db8::22 id 0 \
+ action mirred egress redirect dev bareudp_ns1
+ tc -netns "${NS2}" filter add dev veth23 ingress protocol ipv6 \
+ flower dst_ip 2001:db8::100/128 \
+ action tunnel_key set src_ip 2001:db8::22 dst_ip 2001:db8::21 id 0 \
+ action mirred egress redirect dev bareudp_ns2
+ fi
+
+ # MPLS (unicast) over UDPv6
+ if [ $MPLS_UC ]; then
+ # New encapsulation instructions for bareudp over IPv6
+ tc -netns "${NS1}" filter add dev veth10 ingress protocol mpls_uc \
+ flower mpls_label 103 \
+ action tunnel_key set src_ip 2001:db8::21 dst_ip 2001:db8::22 id 0 \
+ action mirred egress redirect dev bareudp_ns1
+ tc -netns "${NS2}" filter add dev veth23 ingress protocol mpls_uc \
+ flower mpls_label 100 \
+ action tunnel_key set src_ip 2001:db8::22 dst_ip 2001:db8::21 id 0 \
+ action mirred egress redirect dev bareudp_ns2
+ fi
+
+ # Test IPv6 underlay
+ ping_test "UDPv6"
+
+ # Cleanup
+ if [ $IPV4 ]; then
+ ip -netns "${NS0}" route delete 192.0.2.103/32
+ ip -netns "${NS1}" route delete 192.0.2.100/32
+ ip -netns "${NS2}" route delete 192.0.2.103/32
+ ip -netns "${NS3}" route delete 192.0.2.100/32
+ fi
+ if [ $IPV6 ]; then
+ ip -netns "${NS0}" route delete 2001:db8::103/128
+ ip -netns "${NS1}" route delete 2001:db8::100/128
+ ip -netns "${NS2}" route delete 2001:db8::103/128
+ ip -netns "${NS3}" route delete 2001:db8::100/128
+ fi
+ if [ $MPLS_UC ]; then
+ ip -netns "${NS0}" route delete 2001:db8::103/128
+ ip -netns "${NS1}" -family mpls route delete 100
+ ip -netns "${NS2}" -family mpls route delete 103
+ ip -netns "${NS3}" route delete 2001:db8::100/128
+ fi
+ tc -netns "${NS1}" qdisc delete dev veth10 ingress
+ tc -netns "${NS2}" qdisc delete dev veth23 ingress
+ ip -netns "${NS1}" link delete bareudp_ns1
+ ip -netns "${NS2}" link delete bareudp_ns2
+}
+
+while getopts :p o
+do
+ case $o in
+ p) PAUSE_ON_FAIL="yes";;
+ *) exit 1;;
+ esac
+done
+
+# Create namespaces before setting up the exit trap.
+# Otherwise, exit_cleanup_all() could delete namespaces that were not created
+# by this script.
+create_namespaces
+
+set -e
+trap exit_cleanup_all EXIT
+
+setup_underlay
+setup_overlay_common
+
+test_overlay mpls_uc nomultiproto
+test_overlay ipv4 nomultiproto
+test_overlay ipv6 nomultiproto
+test_overlay ipv4 multiproto
+
+if [ "${ERR}" -eq 1 ]; then
+ echo "Some tests failed." >&2
+else
+ ERR=0
+fi
--
2.21.3
Powered by blists - more mailing lists