| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20201214113041.2789043-2-idosch@idosch.org>
Date: Mon, 14 Dec 2020 13:30:27 +0200
From: Ido Schimmel <idosch@...sch.org>
To: netdev@...r.kernel.org
Cc: davem@...emloft.net, kuba@...nel.org, jiri@...dia.com,
mlxsw@...dia.com, Ido Schimmel <idosch@...dia.com>
Subject: [PATCH net-next v2 01/15] mlxsw: reg: Add XM Direct Register
From: Jiri Pirko <jiri@...dia.com>
The XMDR allows direct access to the XM device via the switch.
Signed-off-by: Jiri Pirko <jiri@...dia.com>
Signed-off-by: Ido Schimmel <idosch@...dia.com>
---
drivers/net/ethernet/mellanox/mlxsw/reg.h | 274 +++++++++++++++++++++-
1 file changed, 271 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/mellanox/mlxsw/reg.h b/drivers/net/ethernet/mellanox/mlxsw/reg.h
index 2a89b3261f00..e7979edadf4c 100644
--- a/drivers/net/ethernet/mellanox/mlxsw/reg.h
+++ b/drivers/net/ethernet/mellanox/mlxsw/reg.h
@@ -8469,11 +8469,278 @@ mlxsw_reg_rmft2_ipv6_pack(char *payload, bool v, u16 offset, u16 virtual_router,
mlxsw_reg_rmft2_sip6_mask_memcpy_to(payload, (void *)&sip6_mask);
}
-/* Note that XRALXX register position violates the rule of ordering register
- * definition by the ID. However, XRALXX pack helpers are using RALXX pack
- * helpers, RALXX registers have higher IDs.
+/* Note that XMDR and XRALXX register positions violate the rule of ordering
+ * register definitions by the ID. However, XRALXX pack helpers are
+ * using RALXX pack helpers, RALXX registers have higher IDs.
+ * Also XMDR is using RALUE enums.
*/
+/* XMDR - XM Direct Register
+ * -------------------------
+ * The XMDR allows direct access to the XM device via the switch.
+ * Working in synchronous mode. FW waits for response from the XLT
+ * for each command. FW acks the XMDR accordingly.
+ */
+#define MLXSW_REG_XMDR_ID 0x7803
+#define MLXSW_REG_XMDR_BASE_LEN 0x20
+#define MLXSW_REG_XMDR_TRANS_LEN 0x80
+#define MLXSW_REG_XMDR_LEN (MLXSW_REG_XMDR_BASE_LEN + \
+ MLXSW_REG_XMDR_TRANS_LEN)
+
+MLXSW_REG_DEFINE(xmdr, MLXSW_REG_XMDR_ID, MLXSW_REG_XMDR_LEN);
+
+/* reg_xmdr_bulk_entry
+ * Bulk_entry
+ * 0: Last entry - immediate flush of XRT-cache
+ * 1: Bulk entry - do not flush the XRT-cache
+ * Access: OP
+ */
+MLXSW_ITEM32(reg, xmdr, bulk_entry, 0x04, 8, 1);
+
+/* reg_xmdr_num_rec
+ * Number of records for Direct access to XM
+ * Supported: 0..4 commands (except NOP which is a filler)
+ * 0 commands is reserved when bulk_entry = 1.
+ * 0 commands is allowed when bulk_entry = 0 for immediate XRT-cache flush.
+ * Access: OP
+ */
+MLXSW_ITEM32(reg, xmdr, num_rec, 0x04, 0, 4);
+
+/* reg_xmdr_reply_vect
+ * Reply Vector
+ * Bit i for command index i+1
+ * values per bit:
+ * 0: failed
+ * 1: succeeded
+ * e.g. if commands 1, 2, 4 succeeded and command 3 failed then binary
+ * value will be 0b1011
+ * Access: RO
+ */
+MLXSW_ITEM_BIT_ARRAY(reg, xmdr, reply_vect, 0x08, 4, 1);
+
+static inline void mlxsw_reg_xmdr_pack(char *payload, bool bulk_entry)
+{
+ MLXSW_REG_ZERO(xmdr, payload);
+ mlxsw_reg_xmdr_bulk_entry_set(payload, bulk_entry);
+}
+
+enum mlxsw_reg_xmdr_c_cmd_id {
+ MLXSW_REG_XMDR_C_CMD_ID_LT_ROUTE_V4 = 0x30,
+ MLXSW_REG_XMDR_C_CMD_ID_LT_ROUTE_V6 = 0x31,
+};
+
+#define MLXSW_REG_XMDR_C_LT_ROUTE_V4_LEN 32
+#define MLXSW_REG_XMDR_C_LT_ROUTE_V6_LEN 48
+
+/* reg_xmdr_c_cmd_id
+ */
+MLXSW_ITEM32(reg, xmdr_c, cmd_id, 0x00, 24, 8);
+
+/* reg_xmdr_c_seq_number
+ */
+MLXSW_ITEM32(reg, xmdr_c, seq_number, 0x00, 12, 12);
+
+enum mlxsw_reg_xmdr_c_ltr_op {
+ /* Activity is set */
+ MLXSW_REG_XMDR_C_LTR_OP_WRITE = 0,
+ /* There is no update mask. All fields are updated. */
+ MLXSW_REG_XMDR_C_LTR_OP_UPDATE = 1,
+ MLXSW_REG_XMDR_C_LTR_OP_DELETE = 2,
+};
+
+/* reg_xmdr_c_ltr_op
+ * Operation.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_op, 0x04, 24, 8);
+
+/* reg_xmdr_c_ltr_trap_action
+ * Trap action.
+ * Values are defined in enum mlxsw_reg_ralue_trap_action.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_trap_action, 0x04, 20, 4);
+
+enum mlxsw_reg_xmdr_c_ltr_trap_id_num {
+ MLXSW_REG_XMDR_C_LTR_TRAP_ID_NUM_RTR_INGRESS0,
+ MLXSW_REG_XMDR_C_LTR_TRAP_ID_NUM_RTR_INGRESS1,
+ MLXSW_REG_XMDR_C_LTR_TRAP_ID_NUM_RTR_INGRESS2,
+ MLXSW_REG_XMDR_C_LTR_TRAP_ID_NUM_RTR_INGRESS3,
+};
+
+/* reg_xmdr_c_ltr_trap_id_num
+ * Trap-ID number.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_trap_id_num, 0x04, 16, 4);
+
+/* reg_xmdr_c_ltr_virtual_router
+ * Virtual Router ID.
+ * Range is 0..cap_max_virtual_routers-1
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_virtual_router, 0x04, 0, 16);
+
+/* reg_xmdr_c_ltr_prefix_len
+ * Number of bits in the prefix of the LPM route.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_prefix_len, 0x08, 24, 8);
+
+/* reg_xmdr_c_ltr_bmp_len
+ * The best match prefix length in the case that there is no match for
+ * longer prefixes.
+ * If (entry_type != MARKER_ENTRY), bmp_len must be equal to prefix_len
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_bmp_len, 0x08, 16, 8);
+
+/* reg_xmdr_c_ltr_entry_type
+ * Entry type.
+ * Values are defined in enum mlxsw_reg_ralue_entry_type.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_entry_type, 0x08, 4, 4);
+
+enum mlxsw_reg_xmdr_c_ltr_action_type {
+ MLXSW_REG_XMDR_C_LTR_ACTION_TYPE_LOCAL,
+ MLXSW_REG_XMDR_C_LTR_ACTION_TYPE_REMOTE,
+ MLXSW_REG_XMDR_C_LTR_ACTION_TYPE_IP2ME,
+};
+
+/* reg_xmdr_c_ltr_action_type
+ * Action Type.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_action_type, 0x08, 0, 4);
+
+/* reg_xmdr_c_ltr_erif
+ * Egress Router Interface.
+ * Only relevant in case of LOCAL action.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_erif, 0x10, 0, 16);
+
+/* reg_xmdr_c_ltr_adjacency_index
+ * Points to the first entry of the group-based ECMP.
+ * Only relevant in case of REMOTE action.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_adjacency_index, 0x10, 0, 24);
+
+#define MLXSW_REG_XMDR_C_LTR_POINTER_TO_TUNNEL_DISABLED_MAGIC 0xFFFFFF
+
+/* reg_xmdr_c_ltr_pointer_to_tunnel
+ * Only relevant in case of IP2ME action.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_pointer_to_tunnel, 0x10, 0, 24);
+
+/* reg_xmdr_c_ltr_ecmp_size
+ * Amount of sequential entries starting
+ * from the adjacency_index (the number of ECMPs).
+ * The valid range is 1-64, 512, 1024, 2048 and 4096.
+ * Only relevant in case of REMOTE action.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_ecmp_size, 0x14, 0, 32);
+
+/* reg_xmdr_c_ltr_dip*
+ * The prefix of the route or of the marker that the object of the LPM
+ * is compared with. The most significant bits of the dip are the prefix.
+ * The least significant bits must be '0' if the prefix_len is smaller
+ * than 128 for IPv6 or smaller than 32 for IPv4.
+ */
+MLXSW_ITEM32(reg, xmdr_c, ltr_dip4, 0x1C, 0, 32);
+MLXSW_ITEM_BUF(reg, xmdr_c, ltr_dip6, 0x1C, 16);
+
+static inline void
+mlxsw_reg_xmdr_c_ltr_pack(char *xmdr_payload, unsigned int trans_offset,
+ enum mlxsw_reg_xmdr_c_cmd_id cmd_id, u16 seq_number,
+ enum mlxsw_reg_xmdr_c_ltr_op op, u16 virtual_router,
+ u8 prefix_len)
+{
+ char *payload = xmdr_payload + MLXSW_REG_XMDR_BASE_LEN + trans_offset;
+ u8 num_rec = mlxsw_reg_xmdr_num_rec_get(xmdr_payload);
+
+ mlxsw_reg_xmdr_num_rec_set(xmdr_payload, num_rec + 1);
+
+ mlxsw_reg_xmdr_c_cmd_id_set(payload, cmd_id);
+ mlxsw_reg_xmdr_c_seq_number_set(payload, seq_number);
+ mlxsw_reg_xmdr_c_ltr_op_set(payload, op);
+ mlxsw_reg_xmdr_c_ltr_virtual_router_set(payload, virtual_router);
+ mlxsw_reg_xmdr_c_ltr_prefix_len_set(payload, prefix_len);
+ mlxsw_reg_xmdr_c_ltr_entry_type_set(payload,
+ MLXSW_REG_RALUE_ENTRY_TYPE_ROUTE_ENTRY);
+ mlxsw_reg_xmdr_c_ltr_bmp_len_set(payload, prefix_len);
+}
+
+static inline unsigned int
+mlxsw_reg_xmdr_c_ltr_pack4(char *xmdr_payload, unsigned int trans_offset,
+ u16 seq_number, enum mlxsw_reg_xmdr_c_ltr_op op,
+ u16 virtual_router, u8 prefix_len, u32 *dip)
+{
+ char *payload = xmdr_payload + MLXSW_REG_XMDR_BASE_LEN + trans_offset;
+
+ mlxsw_reg_xmdr_c_ltr_pack(xmdr_payload, trans_offset,
+ MLXSW_REG_XMDR_C_CMD_ID_LT_ROUTE_V4,
+ seq_number, op, virtual_router, prefix_len);
+ if (dip)
+ mlxsw_reg_xmdr_c_ltr_dip4_set(payload, *dip);
+ return MLXSW_REG_XMDR_C_LT_ROUTE_V4_LEN;
+}
+
+static inline unsigned int
+mlxsw_reg_xmdr_c_ltr_pack6(char *xmdr_payload, unsigned int trans_offset,
+ u16 seq_number, enum mlxsw_reg_xmdr_c_ltr_op op,
+ u16 virtual_router, u8 prefix_len, const void *dip)
+{
+ char *payload = xmdr_payload + MLXSW_REG_XMDR_BASE_LEN + trans_offset;
+
+ mlxsw_reg_xmdr_c_ltr_pack(xmdr_payload, trans_offset,
+ MLXSW_REG_XMDR_C_CMD_ID_LT_ROUTE_V6,
+ seq_number, op, virtual_router, prefix_len);
+ if (dip)
+ mlxsw_reg_xmdr_c_ltr_dip6_memcpy_to(payload, dip);
+ return MLXSW_REG_XMDR_C_LT_ROUTE_V6_LEN;
+}
+
+static inline void
+mlxsw_reg_xmdr_c_ltr_act_remote_pack(char *xmdr_payload, unsigned int trans_offset,
+ enum mlxsw_reg_ralue_trap_action trap_action,
+ enum mlxsw_reg_xmdr_c_ltr_trap_id_num trap_id_num,
+ u32 adjacency_index, u16 ecmp_size)
+{
+ char *payload = xmdr_payload + MLXSW_REG_XMDR_BASE_LEN + trans_offset;
+
+ mlxsw_reg_xmdr_c_ltr_action_type_set(payload, MLXSW_REG_XMDR_C_LTR_ACTION_TYPE_REMOTE);
+ mlxsw_reg_xmdr_c_ltr_trap_action_set(payload, trap_action);
+ mlxsw_reg_xmdr_c_ltr_trap_id_num_set(payload, trap_id_num);
+ mlxsw_reg_xmdr_c_ltr_adjacency_index_set(payload, adjacency_index);
+ mlxsw_reg_xmdr_c_ltr_ecmp_size_set(payload, ecmp_size);
+}
+
+static inline void
+mlxsw_reg_xmdr_c_ltr_act_local_pack(char *xmdr_payload, unsigned int trans_offset,
+ enum mlxsw_reg_ralue_trap_action trap_action,
+ enum mlxsw_reg_xmdr_c_ltr_trap_id_num trap_id_num, u16 erif)
+{
+ char *payload = xmdr_payload + MLXSW_REG_XMDR_BASE_LEN + trans_offset;
+
+ mlxsw_reg_xmdr_c_ltr_action_type_set(payload, MLXSW_REG_XMDR_C_LTR_ACTION_TYPE_LOCAL);
+ mlxsw_reg_xmdr_c_ltr_trap_action_set(payload, trap_action);
+ mlxsw_reg_xmdr_c_ltr_trap_id_num_set(payload, trap_id_num);
+ mlxsw_reg_xmdr_c_ltr_erif_set(payload, erif);
+}
+
+static inline void mlxsw_reg_xmdr_c_ltr_act_ip2me_pack(char *xmdr_payload,
+ unsigned int trans_offset)
+{
+ char *payload = xmdr_payload + MLXSW_REG_XMDR_BASE_LEN + trans_offset;
+
+ mlxsw_reg_xmdr_c_ltr_action_type_set(payload, MLXSW_REG_XMDR_C_LTR_ACTION_TYPE_IP2ME);
+ mlxsw_reg_xmdr_c_ltr_pointer_to_tunnel_set(payload,
+ MLXSW_REG_XMDR_C_LTR_POINTER_TO_TUNNEL_DISABLED_MAGIC);
+}
+
+static inline void mlxsw_reg_xmdr_c_ltr_act_ip2me_tun_pack(char *xmdr_payload,
+ unsigned int trans_offset,
+ u32 pointer_to_tunnel)
+{
+ char *payload = xmdr_payload + MLXSW_REG_XMDR_BASE_LEN + trans_offset;
+
+ mlxsw_reg_xmdr_c_ltr_action_type_set(payload, MLXSW_REG_XMDR_C_LTR_ACTION_TYPE_IP2ME);
+ mlxsw_reg_xmdr_c_ltr_pointer_to_tunnel_set(payload, pointer_to_tunnel);
+}
+
/* XRALTA - XM Router Algorithmic LPM Tree Allocation Register
* -----------------------------------------------------------
* The XRALTA is used to allocate the XLT LPM trees.
@@ -11487,6 +11754,7 @@ static const struct mlxsw_reg_info *mlxsw_reg_infos[] = {
MLXSW_REG(rigr2),
MLXSW_REG(recr2),
MLXSW_REG(rmft2),
+ MLXSW_REG(xmdr),
MLXSW_REG(xralta),
MLXSW_REG(xralst),
MLXSW_REG(xraltb),
--
2.29.2
Powered by blists - more mailing lists